Radio Shack ET-551 Bedienungsanleitung

Cat. No. 43-1051

OWNER’S MANUAL

Please read before using this equipment.

ET-551

25-Channel

Cordless Phone

with 10-Number Memor

43-1051.fm Page 1 Tuesday, August 17, 1999 1:08 PM

FEATURES

Your RadioShack ET-551 25-Channel

Cordless Phone with 10-Number

Memory is designed to exacting stan-

dards that ensure reliability, long life,

and outstanding performance.

Its features include:

25 Channels — automatically scans

to find the first clear channel available

and lets you change to a clearer chan-

nel during a call to reduce static inter-

ference.

10-Number Memor

Dialin

— lets

you store up to 16 digits in each of ten

memory locations for easy dialing.

Super CCT Noise-Reduction Cir-

cuitr

— gives you sound clarity com-

parable to that of a corded phone.

Securit

Access-Protection Code —

automatically prevents other cordless

phone users from using your phone

line while the handset is off the base.

COM-LOK®— ensures that other

cordless phone users cannot use your

phone line when the handset is on the

base.

Redial — lets you quickly redial the

last number dialed.

e — lets you send a paging signal

from the base to the handset to page

someone or locate the handset if you

misplace it.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Tone/Pulse Dialin

— lets you use

your phone with either type of service.

Hearin

-Aid Compatibilit

— lets

you use your phone with hearing aids

that have a T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

COM-LOK and RadioShack are registered trademarks used by Tandy Corporation.

43-1051.fm Page 2 Tuesday, August 17, 1999 1:08 PM

Important Note: Cordless phones

such as this one require AC power to

operate. When the AC power is off,

you cannot dial out or receive incoming

calls using your ET-551. To be safe,

you should also have a phone that

does not need AC power to operate

(not a cordless phone) so you can still

make and receive calls if there is an

AC power failure.

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

READ THIS BEFORE

INSTALLATION

Each device that you connect to the

phone line draws power from the

phone line. We refer to this power draw

as the device’s

ringer equivalence

number

, or REN. The REN is shown

on the bottom of the base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phones might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are shown

on the bottom of the base.

Note: You must not connect your

phone to any of the following:

• coin-operated systems

• party-line systems

• most electronic key phone sys-

tems

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

WARNING: To reduce the risk of

fire or shock hazard, do not ex-

pose this product to rain or mois-

ture.

CAUTION !

43-1051.fm Page 3 Tuesday, August 17, 1999 1:08 PM

CONTENTS

Installation ............................................................................................................ 5

Installing the Handset’s Antenna ..................................................................... 5

Selecting a Location ........................................................................................ 5

Placing the Base on a Desk Top ............................................................... 6

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 8

Connecting and Charging the Battery Pack .................................................... 9

Setting the Dialing Mode ............................................................................... 11

Turning the Ringer On or Off ......................................................................... 11

Setting the Volume ........................................................................................ 11

Operation ............................................................................................................ 12

Making and Receiving Calls .......................................................................... 12

Changing the Channel ................................................................................... 12

Using Redial .................................................................................................. 12

Using Flash .................................................................................................... 13

Using Tone Services on a Pulse Line ............................................................ 13

Paging ........................................................................................................... 14

Memory Dialing .............................................................................................. 14

Storing a Number in Memory .................................................................. 14

Entering a Pause .................................................................................... 15

Dialing a Memory Number ...................................................................... 15

Chain-Dialing Service Numbers .............................................................. 15

Testing Stored Emergency Numbers ...................................................... 15

Troubleshootin

................................................................................................. 16

Care and Maintenance ....................................................................................... 18

Replacing the Battery Pack ........................................................................... 19

The FCC Wants You to Know ........................................................................ 20

Lightning ........................................................................................................ 21

43-1051.fm Page 4 Tuesday, August 17, 1999 1:08 PM

INSTALLATION

INSTALLING THE

HANDSET’S ANTENNA

Insert the antenna into the hole at the

top of the handset, then rotate the an-

tenna clockwise until it is secure.

TALK

FLASH

REDIAL MEMORY CHANNEL

ABC DEF

123

456

789

LOW BATT

CHANNEL

RadioShack

GHI JKL MNO

PQRS TUV WXYZ

OPER

SELECTING A

LOCATION

You can place the phone on a desk top

or table, or mount it on a wall. Select a

location that is:

• Near an AC outlet

• Near a telephone line jack

• Out of the way of normal activities

• Away from electrical machinery,

electrical appliances, metal walls

or filing cabinets, wireless inter-

coms, alarms, and room monitors

• Away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of

several locations, try each to see

which provides the best performance.

Caution: The supplied RadioShack

adapter was designed specifically for

your ET-551. Use only the supplied

adapter.

Notes:

• Your telephone connects directly

to a modular telephone line jack. If

your phone line jack is not a mod-

ular jack, you can update the wir-

ing yourself, using jacks and

adapters available at your local

RadioShack store. Or, you can let

the phone company update the

wiring for you.

• The USOC number of the jack to

be installed is RJ11C (RJ11W if

you want to mount it on a wall

plate).

43-1051.fm Page 5 Tuesday, August 17, 1999 1:08 PM

Placing the Base

on a Desk Top

Follow these steps when you place

the base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the LINE jack on

the back of the base.

2. Insert the supplied power

adapter’s barrel plug into the DC

12V jack on the back of the base.

3. Route the adapter’s cord through

the strain relief slot on top of the

base.

T P DC 12V LINE

Strain Relief Slot

4. Plug the adapter into a standard

AC outlet.

5. Plug the modular cord’s other end

into a modular phone line jack.

6. Fully extend the base’s antenna

and place it in a vertical position.

Mounting the Base

on a Wall Plate

1. Plug one end of the supplied short

modular cord into the LINE jack on

the back of the base.

T P DC 12V LINE

43-1051.fm Page 6 Tuesday, August 17, 1999 1:08 PM

2. Insert the supplied power

adapter’s barrel plug into the DC

12V jack on the back of the base.

3. Route the modular cord through

the groove on the bottom of the

base and the adapter cord

through the strain relief slot on top

of the base.

4. Plug the adapter into a standard

AC outlet.

5. Plug the short modular cord’s

other end into the wall plate jack,

then align the base’s keyhole slots

with the wall plate studs and slide

the base downward to secure it.

6. Fully extend the base’s antenna

and place it in a vertical position.

T P DC 12V LINE

Groove

Strain Relief Slot

LINE

RINGER

OFF ON

43-1051.fm Page 7 Tuesday, August 17, 1999 1:08 PM

Mounting the Base

Directly on the Wall

For this mounting method, you need

two wood screws (not supplied) with

heads that fit into the keyhole slots on

the bottom of the base.

1. Drill two holes 315/16

inches apart. Then

thread a screw into

each hole, letting

the heads extend

about

5/16 inch from

the wall.

2. Plug one end of the supplied short

modular cord into the LINE jack on

the back of the base.

3. Insert the supplied power

adapter’s barrel plug into the DC

12V jack on the back of the base.

5/16

315/16

T P DC 12V LINE

4. Route the adapter’s cord through

the strain relief slot on top of the

base.

5. Align the keyhole slots with the

mounting screws and slide the

base downward to secure it.

6. Plug the adapter into a standard

AC outlet.

Strain Relief Slot

RINGER

OFF ON

LINE

43-1051.fm Page 8 Tuesday, August 17, 1999 1:08 PM

7. Plug the cord’s other end into a

modular phone line jack.

8. Fully extend the base’s antenna

and place it in a vertical position.

CONNECTING AND

CHARGING THE

BATTERY PACK

The ET-551 comes with a recharge-

able nickel-cadmium battery pack. Be-

fore using your phone, you must

connect the battery pack then charge

it for about 24 hours.

Follow these steps to charge the bat-

tery pack.

1. Press down and slide off the

handset’s battery compartment

cover as shown.

2. Insert the battery pack’s connec-

tor into the phone’s socket. The

plug fits only one way.

3. Replace the cover.

43-1051.fm Page 9 Tuesday, August 17, 1999 1:08 PM

4. To charge the battery pack, simply

place the handset on the base.

The CHARGE indicator on the

base lights.

Recharge the battery pack when the

LOW BATT indicator on the handset

flashes.

Notes:

• If the CHARGE indicator does not

light when you place the handset

on the base, be sure the battery

pack and AC adapter are correctly

and securely connected.

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work

and you might hear an error tone.

If this happens, return the handset

to the base for a few seconds.

• If the LOW BATT indicator does

not light, but the phone does not

work, recharge the battery pack.

The battery voltage might be too

low to light the indicator.

• If the battery pack gets weak dur-

ing a call, the handset sounds

three beeps every 30 seconds,

and the LOW BATT indicator flash-

es for 2 minutes. After 2 minutes,

the phone automatically discon-

nects. If this happens, you cannot

make another call on the phone

until you recharge the battery

pack.

• About every 30 days, fully dis-

charge the battery pack by keep-

ing the handset off the base until

the LOW BATT indicator lights.

Otherwise, the battery pack loses

its ability to fully recharge.

• Using a pencil eraser, clean the

charging contacts on the handset

and the base about once a month

to make sure they are not dirty or

tarnished.

RINGER

OFF ON

Charge

Indicator

789

LOW BATT

OPER

43-1051.fm Page 10 Tuesday, August 17, 1999 1:08 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack Sprint SP-514 Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Radio Shack

Radio Shack 43-3580 Bedienungsanleitung

Radio Shack

Radio Shack 43-3577 Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack 43-3871 Bedienungsanleitung

Radio Shack

Radio Shack ET-543 Bedienungsanleitung

Radio Shack

Radio Shack ET-919 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack 43-3857 Bedienungsanleitung

Radio Shack

Radio Shack 43-3823 Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack ET-546 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-5862 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call... Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack ET-1106 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1015 Bedienungsanleitung

Radio Shack

Radio Shack 43-3570 Bedienungsanleitung

Radio Shack

Radio Shack ET-521 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack ET-537 Bedienungsanleitung

Radio Shack

Radio Shack 43-3815 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung