Radio Shack PRO-99 Bedienungsanleitung

RadioShack LOGO

PRO-99 500 Channel VHF/Air/UHF/800MHz Handheld Race Scanner

OWNER’S MANUAL –Please read before using this equipment.

20-515

Two-Second Scan/Search Delay –Delays scanning for 2 seconds before moving to another channel, so you

can hear more replies.

Ten Channel-Storage Banks –Store up to 20 channels in each of 10 different banks, to group channels so

you can more easily identify calls.

20 Monitor Memories –Temporarily save up to 20 frequencies located during a search, so you can move

selected frequencies to channel storage later.

Preprogrammed Frequency Ranges –Lets you search for transmissions within preset frequency ranges or

within ranges you set, to reduce search time and select interesting frequencies.

Memory Backup –Keeps the channel frequencies stored in memory for about 1 hour during a power loss.

Triple Conversion Superheterodyne Receiver –Eliminates interference from intermediate frequency (IF)

images, so you hear only the frequency you select.

HyperSearchTM and HyperScanTM –Set the scanner to search at up to 50 steps per second and scan at up

to 25 channels per second, to quickly find interesting transmissions.

Duplicate Frequency Check –Automatically notifies you if you are about to store a frequency you have

already stored, to help avoid waiting storage space.

Tune –Tunes for new and unlisted frequencies starting from a specified frequency.

Priority Channel –Designate a channel to scan every two seconds so you do not miss important calls.

Weather Band Key –Scans seven preprogrammed weather frequencies to keep you informed about current

weather conditions.

Weather Alert –Automatically sounds the alarm tone to advise of hazardous weather conditions when it

detects the alert signal on the local NOAA weather channel.

Lock-Out Function –Set the scanner to skip over specified channels or frequencies when scanning or

searching.

Key Lock –Lock the scanner’s keys to prevent accidentally changing the scanner’s programming.

Two Supplied Antennal with BNC Connector –Select the antenna that best meets your needs. The supplied

stub antenna helps your scanner receive strong local signals and makes the scanner easy to carry and use at

events. The supplied flexible antenna provides excellent reception of weaker signals and is designed to help

prevent antenna breakage.

Liquid Crystal Display –Makes it easy to view and change programming information.

Display Backlight –Makes the scanner easy to read in low light situations.

Three Power Options –Power the scanner from internal batteries (non-rechargeable batteries, rechargeable

Ni-MH (nickel-metal hydride) or regular or high capacity Ni-Cd (nickel-cadmium) batteries), external AC power

(using optional adapters), or vehicle battery power (using optional adapters).

! IMPORTANT !

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for

pertinent information.

! –Warning ! –Important thundervolt –Caution

light –hint notebook –Note

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

CONTENTS

Will add

Thank you for purchasing the RadioShack 500-Channel VHF/Air/UHF/800 MHz handheld Race Scanner. It

lets you in on all the action in the pits or on the track at the big race. This scanner gives you direct access to

over 33,500 frequencies, including those used by participants and staff at auto races, police and fire

departments, ambulance services, and amateur radio services. You can select up to 500 channels to scan,

and you can change your selection at any time.

Your scanner can receive all of these frequencies:

. 29-54 MHz

. 108-136.9875 MHz

. 137-174 MHz

. 406-512 MHz

. 806-823.9875 MHz

. 849-868.9875 MHz

. 894-960 MHz

This Owner’s Manual also includes the section :A General Guide to Scanning” on Page XX to help you target

frequency ranges in your service area so you can search for a wide variety of transmissions.

FCC NOTICE

Your scanner might cause TV or radio interference even when it is operating properly. To determine whether

your scanner is causing the interference, turn off your scanner. If the interference goes away, your scanner is

causing it. Try to eliminate the interference by:

. moving your scanner away from the receiver

. connecting your scanner to an outlet that is on different electrical circuit from the receiver

. contacting your local RadioShack store for help

If you cannot eliminate the interference, the FCC requires that you stop using your scanner.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This

device must not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: Mobile use of this scanner is unlawful or requires a permit in some areas. Check the laws in your area.

SCANNING LEGALLY

Your scanner covers frequencies used by many different groups including police and fire departments,

ambulance services, government agencies, private companies, amateur radio services, military operations,

pager services, and wireline (telephone and telegraph) services. It is legal to listen to almost every

transmission your scanner can receive. However, there are some transmissions you should never

intentionally listen to. These include:

. telephone conversations (cellular, cordless, or other private means of telephone signal transmission)

. pager transmissions

. any scrambled or encrypted transmissions

According to the Electronic Communications Privacy Act (ECPA), you are subject to fines and possible

imprisonment for intentionally listening to, using, or divulging the contents of such a transmission unless you

have the consent of a party to the communication (unless such activity is otherwise illegal).

This scanner has been designed to prevent reception of illegal transmissions. This is done to comply with the

legal requirement that scanners be manufactured so as to not be easily modifiable to pick up those

transmissions. Do not open your scanner’s case to make any modifications that could allow it to pick up

transmissions that it is not legal to listen to. Doing so could subject you to legal penalties.

We encourage responsible, legal scanner use.

PREPARATION

INSTALLING BATTERIES

You can power your scanner with threeAA batteries (not supplied).

Notes

. Dispose of old batteries promptly and properly.

. Do not burn or bury batteries.

. Use only fresh batteries of the required size and recommended type.

. Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or

rechargeable batteries of different capacities.

. If you do not plan to use the scanner for a month or more, remove the batteries. Batteries can leak

chemicals that can destroy electronic parts.

You can use either the black non-rechargeable battery holder or the yellow rechargeable battery holder (both

supplied) to hold the batteries. If you use the yellow battery holder, we recommend nickel-cadmium or

nickel-metal hydride batteries (not supplied).

Warning: Never install non-rechargeable batteries in the yellow rechargeable battery holder.

Non-rechargeable batteries can get hot or explode if you try to recharge them.

1. Press down on the battery compartment cover then slide the cover in the direction of the arrow to remove

it.

2. If you are using non-rechargeable batteries, place them into the black holder, as indicated by the polarity

symbols (+ and -) marked on the holder. Or, if you are using rechargeable batteries, place them into the

yellow holder as indicated by the polarity symbols (+ and -) marked on the holder.

3. Place the battery holder into the battery compartment.

Caution: The battery holder fits only one way inside the battery compartment. Do not force it.

4. Replace the cover.

When Low Battery! flashes on the display and the scanner beeps, or if the scanner stops operating properly,

replace the batteries.

USINGAC POWER

You can power the scanner using a 6V, 300-mA AC adapter and a size C Adaptaplug™ adapter (neither

supplied). Both are available at your local RadioShack store.

Cautions:

! You must use a Class 2 power source that supplies 6VDC and delivers at least 300 mA. Its center tip must

be set to positive and its plug must fit the scanner’s PWR DC 9V jack. Using an adapter that does not meet

these specifications could damage the scanner or the adapter.

. Always connect the AC adapter to the scanner before you connect it to AC power. When you finish,

disconnect the adapter fromAC power before you disconnect it from the scanner.

To power the scanner using an AC adapter, attach the Adaptaplug to the AC adapter so the tip reads positive

(+), then insert the Adaptaplug into the scanner’s PWR DC 9V jack. Connect the other end of the adapter to a

standardAC outlet.

USING VEHICLE BATTERY POWER

You can power the scanner from a vehicle’s 12V power source (such as a cigarette-lighter socket) using a 6V,

300-mA DC adapter and a size C Adaptaplug (neither supplied.) Both are available at your local RadioShack

store.

Cautions:

! You must use a Class 2 power source that supplies regulated 6V DC and delivers at least 300 mA. Its center

tip must be set to positive and its plug must fit the scanner’s PWR DC 6V jack. Using an adapter that does not

meet these specifications could damage the scanner or the adapter.

. Always connect the AC adapter to the scanner before you connect it to the power source. When you finish,

disconnect the adapter from the power source before you disconnect it from the scanner.

To power the scanner using a DC adapter, attach the Adaptaplug to the DC adapter so the tip reads positive

(+), set the adapter’s voltage switch to 9V, then insert the Adaptaplug into the scanner’s PWR DC 6V jack.

Plug the other end of the DC adapter into your vehicle’s cigarette-lighter socket.

Note: If you use a cigarette-lighter power cable and your vehicle’s engine is running, you might hear electrical

noise from the engine while scanning. This is normal.

CHARGING RECHARGEABLE BATTERIES

Your scanner has a built-in charging circuit that lets you charge rechargeable batteries while they are in the

scanner. To charge rechargeable batteries, you need to use an AC adapter which supplies 6V (RadioShack

Cat. No. 273-1758) or a DC adapter which supplies 10V (RadioShack Cat. No. 273-1859). Connect a size C

Adaptaplug to the adapter’s cable with the tip set to positive then insert the Adaptaplug into the scanner’s

PWR DC 6V jack

Notes

. Do not overcharge Ni-Cd batteries. Overcharging causes them to get hot and shortens their life.

. Ni-Cd batteries last longer and deliver more power if you occasionally let them fully discharge. To do this,

simply use the scanner until B flashes on the display and the scanner beeps. Then fully charge the batteries.

It takes between 14 and 16 hours to recharge Ni-MH or 7 and 8 hours to recharge Ni-Cd batteries that are

fully discharged. You can operate the scanner while recharging the batteries, but charging takes longer.

IMPORTANT!

The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates

RadioShack is voluntarily participating in an industry program to collect and recycle these batteries at the end

of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a

convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which

may be illegal in your area. Please call 1-800-THE-SHACK (1-800-843-7422) for information on Ni-Cd battery

recycling and disposal bans/restrictions in your area. RadioShack’s involvement in this program is part of the

company’s commitment to preserving our environment and conserving our natural resources.

CONNECTINGANANTENNA

Connecting a SuppliedAntenna

You must install an antenna before you can operate the scanner.

The supplied stub antenna helps your scanner receive most strong transmissions at events and makes the

scanner easier to carry and use. The supplied flexible antenna provides slightly better reception and helps

your scanner receive strong local signals.

1.Align the slots around the antenna’s connector with the tabs on the antenna jack.

2. Press the antenna down over the jack and turn the antenna’s base clockwise until it locks into place.

Add illust

Connecting an OutdoorAntenna

Instead of a supplied antenna, you can connect an outdoor base-station or mobile antenna (not supplied) to

your scanner using a BNC connector. Your local RadioShack stores sells a variety of antennas. Choose the

one that best meets your needs.

When deciding on a mobile or base-station antenna and its location, consider these points.

. The antenna should be as high as possible on the vehicle or building.

. The antenna and its cable should be as far as possible from sources of electrical noise, such as appliances

or other radios.

. The antenna should be vertical for the best performance.

Always use 50 Ohm coaxial cable, such as RG-58 or RG-8, to connect the base-station or mobile antenna.

For lengths over 50 feet, use RG-8 low-loss dielectric coaxial cable. If the antenna cable’s connector does not

fit in the scanner’s antenna jack, you might also need a PL-259-to-BNC antenna plug adapter. Your local

RadioShack store carries a wide variety of coaxial antenna cable and connectors.

Caution

. Do not run the cable over sharp edges or moving parts that might damage it.

. Do not run the cable next to power cables or other antenna cables.

Once you choose an antenna, follow the mounting instructions supplied with the antenna, after removing a

supplied antenna. Then route the antenna’s cable to the scanner and connect the cable to the scanner’s

antenna jack.

WARNING

Use extreme caution when you install or remove an outdoor antenna. If the antenna starts to fall, let it go! It

could contact overhead power lines. If the antenna touches a power line, contact with the antenna, mast,

cable, or guy wires can cause electrocution and death. Call the power company to remove the antenna. DO

NOT attempt to do so yourself.

CONNECTINGAN EARPHONE /HEADPHONES

For private listening, you can connect an earphone or headphones with a 1/8-inch (3.5 mm) plug to the

(headphone symbol) jack on the top of the scanner. (Your local RadioShack store carries a wide selection of

earphones and headphones). Connecting an earphone or headphones automatically disconnects the internal

speaker.

Add illust

LISTENING SAFELY

Toprotect your hearing, follow these guidelines when you use an earphone or headphones.

. Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume

to a comfortable level.

. Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent

hearing loss.

. Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume

level that does not cause discomfort might still damage your hearing.

TRAFFIC SAFETY

. Do not use an earphone or headphones with your scanner when operating a motor vehicle or riding a

bicycle in or near traffic. Doing so can create a traffic hazard and could be illegal in some areas.

. If you use an earphone or headphones with your scanner while riding a bicycle, be very careful. Do not listen

to a continuous transmission. Even though some earphones or headphones let you hear some outside

sounds when listening at normal volume levels, they still can present a traffic hazard.

CONNECTINGAN EXTENTION SPEAKER

In a noisy area, an amplified extension speaker (available at your local RadioShack store) might provide more

comfortable listening. Plug the speaker cable’s 1/8-inch (3.5 mm) plug into your scanner’s (headphone

symbol) jack

Add illust

Note: Connecting an external speaker disconnects the scanner’s internal speaker.

UNDERSTANDING THE SCANNER

Once you understand a few simple terms used in this manual and familiarize yourself with your scanner’s

features, you can put the scanner to work for you. You simply determine the type of communications you want

to receive, then set the scanner to scan them.

A frequency is the tuning location of a station (expressed in kHz or MHz). To find active frequencies, you can

use the search function.

You can also search the service-search banks, which are preset groups of frequencies categorized by type of

service.

When you find a frequency, you can store it into a programmable memory location called a channel, which is

grouped with your other channels in a channel-storage bank. You can then scan the channel-storage banks

to see if there is activity on the frequencies stored there. Each time the scanner finds an active frequency, it

stays on that channel until the transmission ends.

A LOOK AT THE KEYPAD

If your scanner’s keys seem confusing at first, the following illustration and information should help you

understand each key’s function.

Add illust

Note: Some of the scanner’s keys perform more than one function and are marked with more than one label.

The steps in this Owner’s Manual show only the label on the key appropriate to the action being performed.

FUNC –Lets you use various functions by pressing this key in combination with other keys. When using the

FUNC key, press the FUNC key first, then release it, then quickly press the next key in the function key

sequence.

Hold down for about 2 second, the scanner enters function menu mode.

LIGHT/(KEY SYMBOL) –Locks and unlocks the keypad to prevent accidental entries; turns the backlight on

and off.

(UP)/(DN) –Searches up or down for active frequencies or selects the direction when scanning channels.

< / > -- moves right or left the cursor while text input.

SCAN –Scans any programmed channels. Or, store car numbers and frequencies in the scanner’s channels,

add and delete frequencies from car numbers, display car numbers, and listen to the channel where a car

number is stored.

MAN –Stops scanning and lets you directly enter a channel number. Or, pauses search or tune operation.

SRCH –Lets you search the seven search banks.

WX –Scans the scanner’s preprogrammed weather channels. Or turns the WX alert mode on and off.

1/PRI –Enter a 1, or inputs characters 0 through 9 in text mode. Or, sets and turns the priority function on or

off.

2/DLY –Enter a 2, or inputs characters A through C in text mode. Or, programs a 2-second delay for the

selected channel.

3/L/OUT –Enter a 3, or inputs characters D through F in text mode. Or, lets you lock out selected channels or

frequencies.

4/PAUSE –Enter a 4, or inputs characters G through I in text mode. Or, pauses search or tune operation.

5 –Enter a 5, or inputs characters J through L in text mode.

6 –Enter a 6, or inputs characters M through O in text mode.

7 –Enter a 7,or inputs characters P through S in text mode.

8 –Enter a 8, or inputs characters T through V in text mode.

9 –Enter a 9, or inputs characters W through Z in text mode.

./CLEAR –Enters a decimal point (necessary when programming frequencies) or spaces in text mode. Or,

clears an incorrect entry or returns previous menu.

0 –Enter a 0, or inputs characters . -# _ @ + * & / , $ % ! ^ ( ) ? -> ‘ <-.

ENT (enter) –Enters frequencies into channels.

UNDERSTANDING BANKS

CHANNEL STORAGE BANKS

To make it easier to identify and select the channels you want to listen to, channels are divided into 10 banks

of 20 channels each. Use each channel-storage bank to group frequencies, such as those used by the police

department, fire department, ambulance services, or aircraft (see “Guide to theAction Bands” on Page XX).

For example, the police department might use four frequencies, one for each side of town. You could program

the police frequencies starting with Channel 1 (the first channel in bank 1) and program the fire department

frequencies starting with Channel 21 (the first channels in bank 2).

Andere Handbücher für PRO-99

Inhaltsverzeichnis

Andere Radio Shack Scanner Handbücher

Radio Shack

Radio Shack PRO-94 Bedienungsanleitung

Radio Shack

Radio Shack PRO-26 Bedienungsanleitung

Radio Shack

Radio Shack PRO-2040 Bedienungsanleitung

Radio Shack

Radio Shack PRO-72 Bedienungsanleitung

Radio Shack

Radio Shack PRO-97 Bedienungsanleitung

Radio Shack

Radio Shack PRO-89 Bedienungsanleitung

Radio Shack

Radio Shack PRO-83 Bedienungsanleitung

Radio Shack

Radio Shack PRO-94 Bedienungsanleitung

Radio Shack

Radio Shack PRO-650 Bedienungsanleitung

Radio Shack

Radio Shack 20-427 PRO-2054 Bedienungsanleitung

Radio Shack

Radio Shack PRO-90 Bedienungsanleitung

Radio Shack

Radio Shack Pro-2032 Bedienungsanleitung

Radio Shack

Radio Shack PRO-2050 Bedienungsanleitung

Radio Shack

Radio Shack 200 Ch VHF/Air/UHF Home Scanner Bedienungsanleitung

Radio Shack

Radio Shack PRO-160 Bedienungsanleitung

Radio Shack

Radio Shack ADV0801 Bedienungsanleitung

Radio Shack

Radio Shack Pro 2055 Bedienungsanleitung

Radio Shack

Radio Shack PRO-96 Bedienungsanleitung

Radio Shack

Radio Shack 20-163 Bedienungsanleitung

Radio Shack

Radio Shack PRO-433 Bedienungsanleitung

Radio Shack

Radio Shack PRO-29 Bedienungsanleitung

Radio Shack

Radio Shack PRO-137 Bedienungsanleitung

Radio Shack

Radio Shack PRO-66 Bedienungsanleitung

Radio Shack

Radio Shack Realistic PRO-34 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung