Radio Shack ET-652 Bedienungsanleitung

Cat. No. 43-652

OWNER’S MANUAL

Please read before using this equipment.

ET-652

Two-Line Speakerphone

43-652.fm Page 1 Friday, August 13, 1999 11:00 AM

FEATURES

Your RadioShack ET-652 Two-Line

Speakerphone lets you make or receive

calls on two separate telephone lines

using either the handset or the built in

speakerphone. You can connect up to

five ET-652s to the same telephone line

(depending on the phone line’s power;

see “Read This Before Installation” on

Page 3).

Your ET-652 has these features:

Line Status Indicators — let you see at

a glance if a line is available, in use, or

on hold.

20-Number Memor

Dialin

— lets you

store up to 20 numbers in memory for

easy dialing.

Distinctive Rin

— tells you which line

is ringing.

Redial — lets you quickly redial the last

number dialed.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Hold — lets you put one or both lines on

hold with a separate indicator for each

line.

Volume Control — lets you adjust the

volume you hear through the handset.

Speakerphone — lets you make or an-

swer calls without using the handset.

Tone or Pulse Dialin

— lets you use

your phone with tone or pulse (rotary) di-

aling and lets you switch from pulse to

tone dialing for long-distance, bank-by-

phone, or other special services.

Hearin

-Aid Compatibilit

— lets you

use your phone with hearing aids that

have a T (telephone) switch.

Your ET-652 has been tested and found

to comply with all applicable standards.

This symbol is intended to alert you to

the presence of uninsulated danger-

ous voltage within the product’s enclo-

sure that might be of sufficient

magnitude to constitute a risk of elec-

tric shock. Do not open the product’s

case.

This symbol is intended to inform you

that important operating and mainte-

nance instructions are included in the

literature accompanying this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warnin

: To prevent fire or shock

hazard, do not expose this product

to rain or moisture.

CAUTION

RadioShack is a registered trademark used by Tandy Corporation.

43-652.fm Page 2 Friday, August 13, 1999 11:00 AM

READ THIS BEFORE

INSTALLATION

Your ET-652 conforms to federal regula-

tions, and you can connect it to most

telephone lines. However, each device

that you connect to the telephone line

draws power from the line. We refer to

this power draw as the device’s

ringer

equivalence number

, or REN. The REN

is on the bottom of the base.

If you are using more than one phone or

other device on the line, add up all the

RENs. If the total is more than five, your

phones might not ring. In rural areas, a

total REN of three might impair ringer

operation. If ringer operation is impaired,

remove a device from the line.

FCC STATEMENT

This telephone complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC registration number

and the REN to your telephone compa-

ny. Both numbers are on the bottom of

the telephone.

Note: You must not connect your phone

to any of the following:

• coin-operated systems

• party line systems

• most electronic key phone systems

We recommend you record your

phone’s serial number here. The num-

ber is on the bottom of the base.

Serial Number __________________

43-652.fm Page 3 Friday, August 13, 1999 11:00 AM

CONTENTS

Installation ............................................................................................................... 5

Mounting the Phone ........................................................................................... 5

Connecting the AC Adapter ......................................................................... 5

Connecting to the Phone Lines .................................................................... 5

Connecting the Handset .............................................................................. 6

Mounting on a Wall or Wall Plate ................................................................. 7

Setting the Dialing Mode .................................................................................... 8

Setting the Ringer Volume .................................................................................. 8

Setting the NORM/STORE Switch ........................................................................ 8

Confirming the Line Numbers ............................................................................. 9

Checking/Adjusting the Line-Status Indicators ................................................... 9

Operation ............................................................................................................... 11

Making and Answering Calls ............................................................................ 11

Setting the Volume ........................................................................................... 11

Switching Between the Handset and the Speakerphone ................................. 11

Using HOLD ...................................................................................................... 12

Using REDIAL ................................................................................................... 12

Using FLASH .................................................................................................... 12

Using Tone Services on a Pulse Line ............................................................... 13

Memory Dialing ................................................................................................ 13

Entering a Pause ....................................................................................... 14

Dialing a Memory Number ......................................................................... 14

Chain-Dialing Service Numbers ................................................................. 14

Troubleshootin

.................................................................................................... 15

Care and Maintenance .......................................................................................... 16

The FCC Wants You to Know ........................................................................... 17

Lightning ........................................................................................................... 17

43-652.fm Page 4 Friday, August 13, 1999 11:00 AM

INSTALLATION

MOUNTING THE PHONE

You can place the ET-652 on a desk or

table, mount it on a standard wall plate,

or mount it directly on a wall. Choose a

location that is:

• near an AC outlet

• near a modular telephone line jack

• out of the way of normal activities

Caution: You must use a Class 2

power source that supplies 9

volts DC and delivers at least 300 mA.

Its center tip must be set to negative,

and its plug must fit the ET-652's 9V DC

jack. The supplied AC adapter meets

these specifications. Using an adapter

that does not meet the specifications

could damage the ET-652 or the adapt-

er.

Connecting the AC Adapter

1. Insert the supplied AC adapter's

barrel plug into the 9V DC jack on

the back of the phone.

TEL LINE

ADJUST

LINE 1 LINE 2 DEFEAT

LINE 2 OFF - ON

DC 9V

2. Plug the adapter into a standard AC

outlet.

3. Route the adapter’s cord through

the strain relief slot on the bottom of

the phone.

Connecting to the Phone Lines

To take full advantage of the ET-652’s

capabilities, you must have two phone

lines with separate phone numbers. If

you have only one line, you can order a

second from your phone company.

Notes:

• The line that connects the phone

jack to the phone company wiring

must be twisted-pair cable. Other-

wise, you might hear interference

(crosstalk) between the two lines.

• Your phone connects directly to a

modular phone line jack. If your

phone wiring does not have a modu-

lar jack, you can update it using

jacks and adapters available at your

local RadioShack store, or have the

phone company update it for you.

DESK

Strain

Relief

Slot

43-652.fm Page 5 Friday, August 13, 1999 11:00 AM

• The USOC number of the two-line

jack to be installed is RJ14C

(RJ14W for a wall plate). The USOC

number of a single-line jack is

RJ11C.

Plug one end of the supplied two-line

telephone cord into the jack on the back

of the phone. Then plug the cord’s other

end into a modular telephone line jack.

If you use two single-line jacks, you

must connect the lines with an optional

two-line coupler (such as RadioShack

Cat. No. 279-401).

Note: If you use the ET-652 with only

one line, set LINE 2 DEFEAT on the back

of the phone to OFF. This turns off Line

2’s status indicator.

Connecting the Handset

Plug the supplied coiled handset cord

into the jacks on the handset and the left

side of the phone.

Note: Your local RadioShack store sells

a variety of longer coiled handset cords,

which are especially useful when you

mount the phone on the wall.

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM- STORE

Two-line

Coupler

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM - STORE

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

TEL LINE

ADJUST

LINE 1 LINE 2 DEFEAT

LINE 2 OFF - ON

DC 9V

43-652.fm Page 6 Friday, August 13, 1999 11:00 AM

Mounting on a Wall or Wall

Plate

Notes:

• When mounting the ET-652 on a

wall plate, use the supplied short

modular cord to connect the phone

to the wall plate jack. Your local

RadioShack store carries a variety

of phone line cords.

• To mount the ET-652 directly on a

wall, you need two screws (not sup-

plied) with heads that fit the keyhole

slots on the bottom of the phone.

Drill two holes 315/16

inches (100 mm)

apart. Then thread a

screw into each hole,

letting the heads

extend about 1/8 inch

(3 mm) from the wall.

1. Remove the mounting bracket from

the DESK socket by pressing in the

tabs on both sides and lifting. (You

might need to use a small screw-

driver to press in the tabs.)

2. Put the bracket into the WALL

socket with the arrow on the bracket

aligned to the arrow by the socket,

then push upward until the bracket

snaps into place.

3. Lift the handset holder and turn it

one half turn.

4. Place the phone's two keyhole slots

over the wall plate studs (or the

screws, if you are mounting the

phone on a wall). Press downward

on the phone to secure it.

1/8"

315/16"

DESK

CustomManufactured in China for RadioShack,

A Division of TandyCorporation, Fort Worth, TX 76102

Serial No.

COMPLIES WITH PART68, FCC RULES

USEJACKUSOC RJ14C

CAT.NO. 43-652

HAC

FCC REGISTRATIONNO. AAOCHN-XXXXX-XX-X

RINGER EQUIVALENCE: 0.9B

ET-652

CLASS 2 POWER SUPPLY

TWO-LINESPEAKERPHON E

TELEPHONE

EQUIPMENT

POWER : DC 9V 300mA

TO190GDP00C

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM- STORE

DESK

CustomManufacturedin China for RadioShack,

ivisionofTandy Corporation,Fort Worth, TX 76102

SerialNo.

COMPLIESWITH PART68, FCC RULES

USEJACKUSOCRJ14C

CAT.NO.43-652

HAC

FCCREGISTRATION NO. AAOCHN-XXXXX-XX-X

RINGEREQUIVALENCE: 0.9B

ET-652

CLASS2POWERSUPPLY

TWO-LINESPEAKERPHONE

TELEPHONE

EQUIPMENT

POWER:D

C9V300mA

TO190GDP00C

43-652.fm Page 7 Friday, August 13, 1999 11:00 AM

SETTING THE DIALING

MODE

Set MODE on the side of the phone for

the type of service you have. If you are

not sure which type you have, do this

test.

1. Set MODE to TONE.

2. Press Line 1.

3. Lift the handset and listen for a dial

tone.

4. Press any number other than 0.

Note: If your phone system requires

that you dial an access code (9, for

example) before you dial an outside

number, do not press the access

code number either.

If the dial tone stops, you have

touch-tone service on Line 1. If the

dial tone continues, you have pulse

service.

5. Hang up, then repeat the test for

Line 2.

6. If you have pulse service on either

line, set MODE to PULSE. If you

have tone service on both lines,

leave the switch to TONE.

SETTING THE RINGER

VOLUME

Each line on the ET-652 has a distinc-

tive ring tone and a separate volume

control.

To change the ringer volume, set RING-

ER for the desired line to OFF, LO, or HI.

With the ringer off, you can still answer

calls if you hear an extension phone ring

or see one of the ET-652’s line indica-

tors flash.

SETTING THE NORM/

STORE SWITCH

The NORM/STORE switch is used to

store memory numbers (see “Memory

Dialing” on Page 13). Set it to NORM for

normal operation.

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM - STORE

Line 1

MODE

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM - STORE

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM - STORE

43-652.fm Page 8 Friday, August 13, 1999 11:00 AM

CONFIRMING THE LINE

NUMBERS

Follow these steps to determine which

phone number is connected to which

line.

1. Press

LINE 1, then lift the handset.

2. Dial one of your phone numbers. If

the LINE 2 indicator flashes, the

number is connected to Line 2. If

you hear a busy signal, the number

is connected to Line 1.

After you confirm the phone number for

each line, write the number on the num-

ber card above the line-status indicator.

(Use a paper clip to lift off the card’s

cover.)

CHECKING/ADJUSTING

THE LINE-STATUS

INDICATORS

You can check the status of each line by

glancing at the line-status indicators.

Each line-status indicator is preset to

work correctly with most telephone lines.

However, in some cases you may need

to adjust the indicators to ensure correct

operation.

Follow these steps to test and adjust the

line-status indicators.

1. Press LINE 1, then lift the handset.

The LINE 1 indicator should light

steadily.

2. Press HOLD. The indicator should

flash slowly.

3. If the indicator worked correctly, it

does not need adjustment. Other-

wise, proceed to Step 4.

VOLUME

MIN MAX

LINE 1- RINGER - LINE 2

OFF LO HI OFF LO HI

MODE

PULSE - TONE NORM - STORE

Indicator is: Line is:

Not li

hted Not in use

hted In use

Flashin

rapidly Rin

Flashin

slowly On hold

43-652.fm Page 9 Friday, August 13, 1999 11:00 AM

4. Remove the adjustment tool from its

bracket on the bottom of the phone.

5. Use the adjustment tool to turn the

corresponding LINE 1ADJUST con-

trol on the back of the phone until

the indicator flashes slowly.

6. Press LINE 1. If the indicator still

flashes slowly, turn ADJUST until it

lights steadily.

7. Press HOLD again and repeat Steps

5 and 6 until the indicator works cor-

rectly with the line on and off hold.

Repeat this procedure for Line 2, then

replace the adjustment tool in its brack-

et.

DESK

TEL LINE

ADJUST

LINE 1 LINE 2 DEFEAT

LINE 2 OFF - ON

DC 9V

43-652.fm Page 10 Friday, August 13, 1999 11:00 AM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Telefon Handbücher

Radio Shack

Radio Shack TAD-705 Bedienungsanleitung

Radio Shack

Radio Shack 43-3905 Bedienungsanleitung

Radio Shack

Radio Shack 43-811 Bedienungsanleitung

Radio Shack

Radio Shack ET-893 Bedienungsanleitung

Radio Shack

Radio Shack ET-2105 Bedienungsanleitung

Radio Shack

Radio Shack 43-1107A Handbuch

Radio Shack

Radio Shack ET-296 Bedienungsanleitung

Radio Shack

Radio Shack 43-861 Bedienungsanleitung

Radio Shack

Radio Shack Big Button Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3905 Bedienungsanleitung

Radio Shack

Radio Shack ET-688 Bedienungsanleitung

Radio Shack

Radio Shack HandsfreePhone withCallerID/CallWaiting Bedienungsanleitung

Radio Shack

Radio Shack 13-Memory Big-Button Telephone Bedienungsanleitung

Radio Shack

Radio Shack ET-208 Bedienungsanleitung

Radio Shack

Radio Shack 43-3206 Bedienungsanleitung

Radio Shack

Radio Shack 17-918 Bedienungsanleitung

Radio Shack

Radio Shack 43-855 Bedienungsanleitung

Radio Shack

Radio Shack 43-3910 Bedienungsanleitung

Radio Shack

Radio Shack 4-Line System Speakerphone with Caller ID and Headset... Bedienungsanleitung

Radio Shack

Radio Shack 43-3201 Bedienungsanleitung

Radio Shack

Radio Shack 20-Number Memory Speaker Phone Bedienungsanleitung

Radio Shack

Radio Shack 17-919 Bedienungsanleitung

Radio Shack

Radio Shack Desktop Phone Bedienungsanleitung

Radio Shack

Radio Shack ET-182 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung