Raven Apache AS840 Bedienungsanleitung

VSN® Installation Manual

for ET Apache AS840/850,

AS1040/1050, AS1240/

1250

016-2025-003 Rev. B 11/2021 E40056

016-0171-686 Rev. A 8/18 E31924

We Solve Great Challenges.

DISCLAIMER

While every effort has been made to ensure the accuracy of this document, Raven Industries assumes no

responsibility for omissions and errors. Nor is any liability assumed for damages resulting from the use of

information contained herein.

Raven Industries shall not be responsible or liable for incidental or consequential damages or a loss of anticipated

benefits or profits, work stoppage or loss, or impairment of data arising out of the use, or inability to use, this

system or any of its components. Raven Industries shall not be held responsible for any modifications or repairs

made outside our facilities, nor damages resulting from inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability and accuracy of wireless and

satellite navigation and correction services (e.g. GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot

guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to

use Raven systems, or products used as components of systems, which rely upon the reception of these signals or

availability of these services. Raven Industries accepts no responsibility for the use of any of these signals or

services for other than the stated purpose.

Table of Contents

016-2025-003 Rev. B i

Chapter 1 Important Safety Information............................................................................. 1

General ............................................................................................................................................................................2

Instructions for Wire Routing .................................................................................................................................2

Chapter 2 Introduction............................................................................................................. 5

Preparing for Installation ..........................................................................................................................................5

Prerequisites .............................................................................................................................................................................5

Recommendations .................................................................................................................................................................5

Point of Reference ..................................................................................................................................................................5

Updates ...........................................................................................................................................................................6

Kit Contents ...................................................................................................................................................................7

Chapter 3 Installation ............................................................................................................... 9

Tank Fill Bracket Kit (50 Series Machines) ..........................................................................................................9

Install the Tank Fill Bracket ..................................................................................................................................................9

Install the VSN® Bracket Assembly (50 Series Machines) .......................................................................10

Mount the VSN® Bracket .................................................................................................................................................10

Mount the VSN® Guidance Camera ............................................................................................................................11

Install the VSN® Bracket Assembly (40 Series Machines) .......................................................................12

Mount the VSN® Bracket .................................................................................................................................................12

Mount the VSN® Guidance Camera ............................................................................................................................14

System Diagram ........................................................................................................................................................16

Cable Installation ......................................................................................................................................................17

Inside of Cab ..........................................................................................................................................................................17

Outside of Cab ......................................................................................................................................................................19

Table of Contents

ii VSN® Installation Manual for ET Apache AS840/850, AS1040/1050, AS1240/1250

CHAPTER

Important Safety Information: 1

CHAPTER 1

IMPORTANT SAFETY

INFORMATION

Read this manual and the operation and safety instructions included with your implement and/or controller

carefully before installing the VSN system.

• Follow all safety information presented within this manual.

• If you require assistance with any portion of the installation or service of your Raven equipment, contact your

local Raven dealer for support.

• Follow all safety labels affixed to the VSN system components. Be sure to keep safety labels in good condition

and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels,

contact your local Raven dealer.

When operating the machine after installing VSN, observe the following safety measures:

• Be alert and aware of surroundings.

• Do not operate VSN or any agricultural equipment while under the influence of alcohol or an illegal substance.

• Remain in the operator’s position or a safe working distance away from the booms at all times when VSN is

engaged.

• Disable VSN when exiting from the operator’s seat and machine.

• Do not drive the machine with VSN enabled on any public road.

• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling

VSN when the safe working distance has diminished.

• Ensure VSN is disabled prior to starting any maintenance work on VSN or the machine.

• The machine must remain stationary and switched off, with the booms unfolded and supported, during

installation or maintenance.

NOTICE

WARNING

CHAPTER 1

2 VSN® Installation Manual for ET Apache AS840/850, AS1040/1050, AS1240/1250

GENERAL

• Always verify that the power leads are connected to the correct polarity as marked. Reversing the power leads

could cause severe damage to the equipment.

• Ensure that the power cable is the last cable to be connected.

• A minimum of 12 VDC is required for system operation with a maximum of 15 VDC.

INSTRUCTIONS FOR WIRE ROUTING

The word “harness” is used to mean all electrical leads and cables, bundled and unbundled. When installing

harness, secure it at least every 30 cm (12in) to the frame. Follow existing harness as much as possible and use

these guidelines:

Harness should not contact or be attached to:

• Lines and hoses with high vibration forces or pressure spikes

• Lines and hoses carrying hot fluids beyond harness component specifications

Avoid contact with any sharp edge or abrading surfaces such as, but not limited to:

• Sheared or flame cut edges

• Edges of machined surfaces

• Fastener threads or cap screw heads

• Ends of adjustable hose clamps

• Wire exiting conduit without protection, either ends or side of conduit

• Hose and tube fittings

Routing should not allow harnesses to:

• Hang below the unit

• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris,

attachments)

• Be placed in areas of or in contact with machine components which develop temperatures higher than the

temperature rating of harness components

• Wiring should be protected or shielded if it needs to route near hot temperatures beyond harness component

specifications

Harnessing should not have sharp bends

Allow sufficient clearance from machine component operational zones such as:

• Drive shafts, universal joints and hitches (i.e. 3-point hitch)

• Pulleys, gears, sprockets

• Deflection and backlash of belts and chains

• Adjustment zones of adjustable brackets

CAUTION

Important Safety Information: Instructions for Wire Routing 3

IMPORTANT SAFETY INFORMATION

• Changes of position in RS1 HD and suspension systems

• Moving linkages, cylinders, articulation joints, attachments

• Ground engaging components

For harness sections that move during machine operation:

• Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or

rubbing, especially in articulation and pivot points

• Clamp harnesses securely to force controlled movement to occur in the desired harness section

• Avoid sharp twisting or flexing of harnesses in short distances

• Connectors and splices should not be located in harness sections that move

Protect harnesses from:

• Foreign objects such as rocks that may fall or be thrown by the unit

• Buildup of dirt, mud, snow, ice, submersion in water and oil

• Tree limbs, brush and debris

• Damage where service personnel or operators might step or use as a grab bar

• Damage when passing through metal structures

IMPORTANT:

•Avoid directly spraying electrical components and connections with high pressure water. High

pressure water sprays can penetrate seals and cause electrical components to corrode or

otherwise become damaged. When performing maintenance:

•Inspect all electrical components and connections for damage or corrosion. Repair or replace

components, connections, or cable as necessary.

•Ensure connections are clean, dry, and not damaged. Repair or replace components,

connections, or cable as necessary.

•Clean components or connections using low pressure water, pressurized air, or an aerosol

electrical component cleaning agent.

•Remove visible surface water from components, connections, or seals using pressurized air or an

aerosol electrical component cleaning agent. allow components to dry completely before

reconnecting cables.

CHAPTER 1

4 VSN® Installation Manual for ET Apache AS840/850, AS1040/1050, AS1240/1250

CHAPTER

Introduction: Preparing for Installation 5

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the VSN system!

The following instructions are designed to assist with the proper installation of the VSN system. Refer to the VSN

Calibration & Operation Manual (P/N 016-2020-001) for assistance with calibrating and using the VSN system.

PREPARING FOR INSTALLATION

Before installing the VSN system, park the machine where the ground is level, clean, and dry. Turn off the machine

and leave it turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this

manual to complete the installation process.

PREREQUISITES

The following components must be installed with the VSN system.

•RS1™

• Viper® 4 with ROS version 3.4 or newer

Follow the installation instructions provided with these components before installing VSN.

RECOMMENDATIONS

Raven Industries recommends the following best practices when installing or operating the VSN system for the

first time or at the start of the season:

• Install the VSN unit in the recommended location.

• Use part numbers to help identify parts.

• Do not remove the plastic wrap from a part until it is necessary for installation.

POINT OF REFERENCE

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

CHAPTER 2

6 VSN® Installation Manual for ET Apache AS840/850, AS1040/1050, AS1240/1250

UPDATES

Software and manual updates are available on the Raven Applied Technology website:

http://www.ravenprecision.com

At Raven Industries, we strive to make your experience with our products as rewarding as

possible. One way to improve this experience is to provide us with feedback on this manual.

Your feedback will help shape the future of our product documentation and the overall service we

provide. We appreciate the opportunity to see ourselves as our customers see us and are eager

to gather ideas on how we have been helping or how we can do better.

To serve you best, please send an email with the following information to

techwriting@ravenind.com

-VSN® Installation Manual for ET Apache AS840/850, AS1040/1050, AS1240/1250

-016-2025-003 Rev. B

-Any comments or feedback (include chapter or page numbers if applicable).

-Let us know how long have you been using this or other Raven products.

We will not share your email or any information you provide with anyone else. Your feedback is

valued and extremely important to us.

Thank you for your time.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raven Landwirtschaftliche Geräte Handbücher

Raven

Raven AutoBoom XRT Bedienungsanleitung

Raven

Raven SmarTrax MD Bedienungsanleitung

Raven

Raven SC1 Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven Case IH Patriot 3XX0 Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

Raven

Raven Spray Air 2010 Predator Bedienungsanleitung

Raven

Raven SC1 Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven CRX Gebrauchs- und Pflegehandbuch

Raven

Raven OmniSeed Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven SmarTrax Bedienungsanleitung

Raven

Raven FLOWMAX 220 Bedienungsanleitung

Raven

Raven Hagie Hawkeye STS Bedienungsanleitung

Raven

Raven CaseIH 2100 Series Bedienungsanleitung

Raven

Raven AutoBoom Bedienungsanleitung

Raven

Raven Sidekick Pro Bedienungsanleitung

Raven

Raven SC1 Bedienungsanleitung

Raven

Raven SmarTrax Gebrauchs- und Pflegehandbuch

Raven

Raven AutoBoom Bedienungsanleitung

Raven

Raven AutoBoom Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung

TURF TANK

TURF TANK One+ Bedienungsanleitung