Raynor SENTINEL III 84505RRGD Bedienungsanleitung

CONTENTS

Preparation . . . . . . . . . . . . . . . .2-5

Assembly . . . . . . . . . . . . . . . . .6-7

Installation . . . . . . . . . . . . . . . 8-15

Install the Door Control. . . . . . 16-17

Install the Protector System®. . 18-21

Power. . . . . . . . . . . . . . . . . . 22-23

Adjustments . . . . . . . . . . . . . 24-26

Operation . . . . . . . . . . . . . . . 27-34

Maintenance . . . . . . . . . . . . . . . 35

Troubleshooting. . . . . . . . . . . 36-37

Accessories. . . . . . . . . . . . . . . . 38

Warranty. . . . . . . . . . . . . . . . . . 39

Repair Parts . . . . . . . . . . . . . 42-43

Raynor Garage Doors

1101 E. River Road

Dixon, Illinois 61021

www.raynor.com

Wi-Fi®Garage Door

Opener

Model 84505RRGD

DC Belt Drive

FOR RESIDENTIAL USE ONLY

■Please read this manual and the enclosed safety materials carefully!

■Fasten the manual near the garage door after installation.

■The door WILL NOT CLOSE unless the Protector System®is connected and properly

aligned.

■Periodic checks of the garage door opener are required to ensure safe operation.

■This garage door opener is ONLY compatible with myQ®and Security+ 2.0®

accessories.

■DO NOT enable the Timer-to-Close feature if you are installing the garage

door opener on a one-piece door. The Timer-to-Close is to be used ONLY with

sectional doors.

Download the free myQ®App

Monitor and control your garage from anywhere and

get real-time alerts with peace of mind.

Available on most iOS and Android Devices

myQ®Serial Number

Write down the following information for future reference:

/ /

myQ®Serial Number:

Product Serial Number:

Date of Purchase:

myQ®Serial Number

Product Serial Number

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the

possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard

may come from something mechanical or from electric shock. Read the warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your

garage door and/or the garage door opener if you do not comply with the cautionary statements that

accompany it. Read them carefully.

WARNING: This product can expose you to chemicals including lead, which are known to the State of

California to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

Unattended Operation

The Timer-to-Close (TTC) feature, the myQ® App, and myQ® Garage Door and Gate Monitor are examples of

unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to

close without being in the line of sight of the door is considered unattended close. The Timer-to-Close (TTC)

feature, the myQ® App, and any other myQ® devices are to be used ONLY with sectional doors.

Preparation

Before You Connect with Your Smartphone

Monitor and control your garage door from anywhere using the myQ® App.

You will need:

•Wi-Fi® enabled smartphone, tablet or laptop

•Broadband Internet Connection

•Wi-Fi® signal in the garage (2.4 GHz, 802.11b/g/n required)

•Password for your home network (router's main account, not guest network)

TEST THE WI-FI®SIGNAL STRENGTH

Make sure your mobile device is connected to your Wi-Fi® network. Hold your mobile device in the place where

your garage door opener will be installed and check the Wi-Fi® signal strength.

Check Signal Strength. If you see:

Wi-Fi signal is strong.

The garage door opener will

connect to your Wi-Fi network.

Wi-Fi signal is weak.

The garage door opener may connect to your

Wi-Fi network. If not, try one of the options

below to improve the Wi-Fi signal:

No Wi-Fi signal.

The garage door opener will not be able to

connect to your Wi-Fi network. Try one of the

options below to improve the Wi-Fi signal:

• Move your router closer to the garage door opener to minimize

interference from walls and other objects

• Buy a Wi-Fi range extender

See page 29 to connect the garage door opener to a mobile device.

Check the Door

To prevent possible SERIOUSINJURYor DEATH:

•ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An

unbalanced garage door may NOT reverse when required.

•NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their

hardware, ALLof which are under EXTREME tension.

•Disable ALLlocks and remove ALLropes connected to garage door BEFORE installation and operating

garage door opener to avoid entanglement.

•DO NOT install on a one-piece door if using devices or features providing unattended close.

Unattended devices and features are to be used ONLY with sectional doors.

To prevent damage to garage door and opener:

•ALWAYS disable locks BEFORE installing and operating the opener.

•ONLY operate garage door opener at 120V, 60Hz to avoid malfunction and damage.

Before you begin:

1. Disable locks and remove any ropes connected to the garage door.

2. Lift the door halfway up. Release the door. If balanced, it should stay in place,

supported entirely by its springs.

3. Raise and lower the door to check for binding or sticking. If your door binds,

sticks, or is out of balance, call a trained door systems technician.

4. Check the seal on the bottom of the door. Any gap between the floor and the

bottom of the door must not exceed 1/4" (6 mm). Otherwise, the safety reversal

system may not work properly.

5. The opener should be installed above the center of the door. If there is a torsion

spring or center bearing plate in the way of the header bracket, it may be

installed within 4feet (1.2 m) to the left or right of the door center. See page 10.

Torsion

Spring

Extension

Spring

Preparation

Tools Needed

3/16

5/32

5/16

7/16

1/2

5/8

9/16

1/4

7/16

Preparation

Carton Inventory

Accessories will vary depending on the garage door opener model purchased. Depending on your specific

model, other accessories may be included with your garage door opener. The instructions for these accessories

will be attached to the accessory and are not included in this manual. The images throughout this manual are

for reference and your product may look different.

A. Header bracket

B. Pulley and bracket

C. Door bracket

D. Curved door arm

E. Straight door arm

F. Trolley

G. Emergency release rope and handle

H. Rail

I. Garage door opener

J. Sprocket cover with hex screws

K. Belt

L. Multi-function control panel

M. White and red/white wire

N. The Protector System®

Safety reversing sensors with white and white/black wire attached: Sending senor (1), receiving

sensor (1), and safety sensor brackets (2)

O. Safety labels and literature

P. Rail grease

Q. Remote control

Go to page 38 for replacement or additional accessories.

ASSEMBLY HARDWARE

Washered Bolt 5/16"-18 x 1/2" (2) [mounted in the top of the garage door opener]

INSTALLATION HARDWARE

Hex Bolt 5/16"-18 x 7/8" (4) Lock Washer 5/16"-16 (4)

Lag Screw 5/16"-9 x 1-5/8" (2) Self-Threading Screw 1/4"-14 x 5/8" (2)

Clevis Pin 5/16" x 2-3/4" (1) Ring Fastener (3)

Clevis Pin 5/16" x 1-1/4" (1) Hex Screw 10-24 (2)

Clevis Pin 5/16" x 1" (1) Wing Nut (2)

Nut 5/16"-18 (4)

DOOR CONTROL HARDWARE

Screw 6AB x 1-1/4" (2) Drywall Anchors (2)

Screw 6-32 x 1" (2)

Not

Provided Not

Provided

Preparation

Assembly

1 Attach the Rail to the Garage Door Opener

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

•ALWAYS keep hand clear of sprocket while operating opener.

•Securely attach sprocket cover BEFORE operating.

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of

the opener.

NOTE: ONLY use the bolts removed from the garage door opener. Place the garage door opener on the packing

material to prevent scratching.

1. Remove the two bolts from the top of the garage door opener.

2. Align the rail and the Styrofoam over the sprocket. Cut the tape from the rail, belt, and styrofoam.

3. Fasten the rail with the previously removed bolts.

4. Position the belt around the garage door opener sprocket.

5. Attach the sprocket cover over the garage door opener sprocket and attach with hex screws.

Washered Bolt 5/16"-18x1/2"

(Mounted in the garage door opener) (2)

Hex Screw #8x3/8"

(Packed with the sprocket cover)

HARDWARE

Washered Bolt

5/16"-18x1/2"

Hex Screw

#8x3/8"

Assembly

2 Tighten the Belt

1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not

use any tools.

2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley.

3. Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter turn

until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt

tension.

Spring Trolley Nut

(To motor unit)

Nut ring

slot

Nut Ring Nut Ring

AFTER RELEASE

1-1/4"

(3.18 cm)

BEFORE

(2.5 cm)

Installation

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly

balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems

technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid

entanglement.

5. Where possible, install the door opener 7 feet (2.13 m) or more above the floor.

6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding

contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught

in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

•within sight of the garage door.

•out of reach of small children at a minimum height of 5feet (1.5m) above floors, landings, steps

or any other adjacent walking surface.

•away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control in a prominent location.

11. Place emergency release/safety reverse test label in plain view on inside of garage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a 1-

1/2" (3.8cm) high object (or a 2x4 laid flat) on the floor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric power

BEFORE performing ANY service or maintenance.

14. DO NOT install on a one-piece door if using devices or features providing unattended close.

Unattended devices and features are to be used ONLY with sectional doors.

15. SAVE THESE INSTRUCTIONS.

Installation

1 Determine the Header Bracket Location

To prevent possible SERIOUS INJURY or DEATH:

•Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise

garage door might NOT reverse when required. DO NOT install header bracket over drywall.

•Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.

•NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware,

ALL of which are under EXTREME tension.

•ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An

unbalanced garage door might NOT reverse when required.

•DO NOT enable the Timer-to-Close functionality if operating either one-piece or swinging garage

doors. To be enabled ONLY when operating a sectional door.

Close the door and mark the inside vertical centerline of the garage door.

Extend the line onto the header wall above the door. You can fasten the header bracket within 4 feet (1.22 m) of

the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach

it to the ceiling when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain

approximately 1/2" (1 cm). If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws

(not provided) to securely fasten the 2x4 to structural supports.

Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall

2" (5 cm) above the high point. This height will provide travel clearance for the top edge of the door.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height

possible, or refer to page 10 for ceiling installation.

Header Wall

Unﬁnished

Ceiling

Vertical Centerline

of Garage Door

2x4

Structural

Supports

Level

(Optional)

OPTIONAL

CEILING

MOUNT FOR

HEADER

BRACKET

Sectional door with curved track

Header Wall

Track

2" (5 cm)

Highest Point

of Travel

Door

Installation

2 Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the

instructions which will work best for your particular requirements. Do not install the header bracket over

drywall. If installing into masonry, use concrete anchors (not provided).

HARDWARE

Lag Screw 5/16"-9x1-5/8"

OPTION A - WALL INSTALLATION

1. Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as

shown (with the arrow pointing toward the ceiling).

2. Mark the vertical set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot

holes and fasten the bracket securely to a structural support with lag screws.

Wall Mount

Optional

Mounting

Holes

Vertical

Centerline of

Garage Door

(Header Wall)

Header

Bracket

2x4 Structural

Support

Door Spring

(Garage Door)

Highest Point of

Garage Door

Travel

Horizontal

Line

Lag Screw

5/16"-9 x 1-5/8"

OPTION B - CEILING INSTALLATION

1. Extend the vertical centerline onto the ceiling as shown.

2. Center the bracket on the vertical mark, no more than 6" (15cm) from the wall. Make sure the arrow is

pointing toward the wall. The bracket can be mounted flush against the ceiling when clearance is minimal.

3. Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the

hardware provided.

(Header Wall)

Ceiling Mounting Holes

(Finished Ceiling)

Vertical

Centerline of

Garage Door

Header

Bracket

6" (15 cm)

Maximum

Door Spring

(Garage Door)

Lag Screw

5/16"-9 x 1-5/8"

Inhaltsverzeichnis

Andere Raynor Garagentoröffner Handbücher

Raynor

Raynor ULTRA 3595RGDS 3/4 HP Bedienungsanleitung

Raynor

Raynor 2220RGD 1/2 HP Bedienungsanleitung

Raynor

Raynor 3245RGD 1/3 HP Bedienungsanleitung

Raynor

Raynor PILOT 2265RGD Bedienungsanleitung

Raynor

Raynor 8165RGD CONTRACTOR Series Corporal II Bedienungsanleitung

Raynor

Raynor ULTRA SAFETY SIGNAL 2595RGD Bedienungsanleitung

Raynor

Raynor 3255RGD Bedienungsanleitung

Raynor

Raynor Commander II Safety Signal 3240RGD Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

Raynor

Raynor 3280RGDM Bedienungsanleitung

Raynor

Raynor 8500WRGD Bedienungsanleitung

Raynor

Raynor Ultra II 8587RGD Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor 3265RGDM 1/2 HP Bedienungsanleitung

Raynor

Raynor MJ5011UCHB Bedienungsanleitung

Raynor

Raynor 87504RGD-267 Bedienungsanleitung

Raynor

Raynor Premium series 8500RGD Prodigy II Bedienungsanleitung

Raynor

Raynor 3265RGDM 1/2 HP Bedienungsanleitung

Raynor

Raynor 8550WRGD Admiral II Bedienungsanleitung

Raynor

Raynor FliteStar-7 Bedienungsanleitung

Raynor

Raynor MT5011UCHB Bedienungsanleitung

Raynor

Raynor 3595RGD 3/4 HP Bedienungsanleitung

Raynor

Raynor Navigator 1245RGD Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung