Red Arrow PC10A Bedienungsanleitung

PAGE 2 (TWO - INSIDE DPS)

Photocells

Product Codes: PC10A, PC10AH

Box Contents -

1 x PC10A - Photocell Kit

1 x PC10AH - Photocell Head

Dimensions: PC10A: L: 130 x Ø: 80mm

PC10AH: L: 64 x Ø: 80mm

Material: Polycarbonate

IP Rating: IP65

Guarantee: 1 year

Safety Warning

• The installation should be carried out

by a qualied electrician in compliance

with the current edition of the IEE

Wiring Regulations.

• Prior to installation, carry out the

necessary risk assessment considering

the people who could be at risk,

the level of risk and the precautions

required to control the risk

• Ensure that the circuit supply is

isolated either by the circuit supply

fuse being removed or the applicable

circuit breaker being turned o before

installation or any maintenance.

• Check the total load on the circuit

ensuring the luminaire does not exceed

the rating of the circuit cable, fuse or

circuit breaker.

• Long-term use and voltage uctuations

can reduce the life span of the tting.

• If the tting incorporates control gear,

ensure careful sizing to avoid instances

of nuisance tripping of the protective

device used in the installation.

• Follow the provided installation

instructions, using the xings supplied

or recommended.

• Keep out of reach of children.

IP65

GUARANTEE

INSTALLATION INSTRUCTIONS

PAGE 1 (FRONT PAGE)

Specication

1. Carefully choose the correct position to install the photocell kit considering the following guide lines:

• Where possible there should be a clear view of the sky, allowing sucient distance when mounting under eves.

• For optimum performance the position chosen should have a clear view of north.

• Be away from view of any articial light source.

• Be away from view of the light source the unit is to control.

2. Securely x the base holder to a vertical wall so that the head will be facing up when tted.

3. Fit the gasket into the base holder foam side up.

4. Enter the supply & load cable into the base through the hole in the bottom of the base ensuring that a cable gland grommet or sealing compound is used

to maintain the IP rating of the unit.

5. Terminate the cable into the Nema socket observing the correct connections;

“li” = live (supply in)

“lo”= load (supply out)

“n” = neutral (the neutral to the load does not need to pass through the unit and can be taken directly).

6. Place the Nema socket into the base holder with the arrow printed on the socket pointing towards north. If north is located behind the unit towards the

mounting surface then the arrow should be aligned pointing in the direction of best natural light.

7. The base holder has 2 locating pins for the Nema socket to t onto, the Nema socket should then be secured using the 2 counter sunk self tapping screws

provided.

8. Align the largest of the 3 brass feet marked ‘neutral’ on the photocell head with the largest slot in the nema socket, push the photocell head into the Nema

socket and gently turn clockwise to lock into place.

Installation Instructions

Ø80mm

W64mm

W130mm

INS/ACCESSORIES/0001/PC10/V4

T: 0800 195 0006

sales@redarrowelectrical.co.uk

Red Arrow Electrical Distribution

Cortonwood Drive, Brampton,

Barnsley, S73 0UF

redarrowelectrical.co.uk

PAGE 2 (TWO - INSIDE DPS)

This product is guaranteed for a period of 1 year from the date of purchase. The guarantee is invalid in the case of improper use, tampering, removal of the Q.C.

date label, installation in an improper working environment or installation not according to the current edition of the I.E.E. Wiring Regulations (BS7671). The

guarantee is also invalidated if the luminaire has been insulation tested. Should this product fail during the guarantee period it will be replaced free of charge,

subject to correct installation and return of the faulty unit. We do not accept responsibility for any installation costs associated with the replacement of this

product. Your statutory rights are not aected. We reserve the right to alter specications without prior notice.

• This tting will require routine cleaning if used in adverse (dust, paint, welding, oils etc) environments. Do not use solvents, aggressive detergents or

abrasives.

• When this tting comes to the end of it’s life or you choose to replace it, please do not dispose of it with your normal waste. Please recycle where the

facilities exist, check with your local authority for suitable options.

PAGE 1 (FRONT PAGE)

Guarantee

Maintenance

• The photocell always powers up in the“on”position, if in bright daylight it will switch o within 2 minutes.

• To test for correct operation cover the photocell with the packing box, after a short delay, 15-120 seconds, The photocell will operate and power will be

applied to the load. If tested in bright daylight after a similar delay the photocell will turn o the power to the load when the packaging box is removed.

Operation & Testing

• The load stays on:

The photocell is in a shady or dark position.

The neutral is not connected.