RedWing RC Sbach Bedienungsanleitung
Our airplane model:
1 All our plane have the matching carbon fiber servo arms, carbon
fiber main and tail landing gear, carbon fiber spinner and wood
propeller available.
2
3
4Removable wings and stabs
Pre-glued cowling ring with
blind nuts mounted.
Canister installation position
in Fuselage
5Pre drilled servo control horns
6
7Pre installed firewall
8Pre install pull pull wire with
ball links on rudder
9Carbon Fiber wing tube include
10 Floor and dashboard for cockpit
Laser cut engine mounting
templates
Caution!
1 You should not regard this plane as a toy!
2 To ensure safety, please read this instruction manual thoroughly
before assembly.
3 Building and operating a model plane requires diligent practice and
correct guidance. An inexperienced flyer can cause serious injury
and property damage.
4 Seek the assistance of an experienced RC pilot or model airplane
club for help with assembly, operation and maintenance to ensure
your flying experience is both enjoyable and safe.
5 Fly only in AMA (Academy of Model Aeronautics) approved areas.
Approved areas or areas approved by the Model Association of
your country.
Main Landing Gear and Tail Wheel Unit
Tail Wheel Unit
1
2
3
Drill a hole and make it fit
the steering tube.
Do not glue it into position untill the tail
wheel installation step is completed.
Assembly photo for the tail
wheel parts.
Use the tail wheel bracket as
a template and drill holes for
the mounting bolts.
4
5
6
7
Insert the steering arm into
the rudder steering tube and
position the tube ready for
gluing. Tighten the set nuts.
Epoxy the steering tube in
place as shown.
Install the blind nuts through
the openning in the rear of
the fuselage.
Attach the tail wheel bracket
and secure the bolts with
Blue Loctite.
Install the hatch with 4 self-
tapping screws
Main Landing Gear Istallation
1
2
Install the landing gear in the
pre-drilled holes with the
supplied bolts and locking
nuts.
Secure the bolts with Blue
Loctite
Install the landing gear axles
with lock nuts but do not
tighten yet.
All parts for the main landing
gear
3
4
5
6Mount the wheel pants and
secure the bolts with a drop
of Blue Loctite.
Install the wheel and tighten
the collar set screw using a
drop of Blue Loctite. Make
sure the wheel rotates freely.
Slipping the wheel pant over
the axles and mark the
position for the two attached
bolts.
Drill the holes for the
attached bolts and install the
blind nuts as shown.
Main Wing Assembly
1
2
Parts for Main wing
installation
Remove the covering from
the servo position. Find out
the slot pre-opened for
rudder control horn, remove
the film. as shown.
Fit the control horn into the
slot, glue the horns into the
aileron of each side.
3
4
5Put the servo into the servo
hole, and mark the position
for the screw to fixup the
servo. Pull the extension lead
through to the root of the
wing.
Drill holes for the servo
mounting screws and harden
the wood around the holes
with a drop of thin CA.
Use the safety clips (buy
separately) to secure the
servo and servo extension
connected.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere RedWing RC Spielzeug Handbücher
RedWing RC
RedWing RC Wilga 100cc Bedienungsanleitung
RedWing RC
RedWing RC Yak55 Bedienungsanleitung
RedWing RC
RedWing RC EXTRA 330 50CC Bedienungsanleitung
RedWing RC
RedWing RC 30cc MXS-Bach - Red - FUSION CONCEPT Bedienungsanleitung
RedWing RC
RedWing RC Edge 540 v3 Bedienungsanleitung
RedWing RC
RedWing RC Slick Bedienungsanleitung
