Remaco PRO-1515 Bedienungsanleitung
Brown (to Live)
Blue (to Neutral)
Green (to Earth)
STOP UP
DOWN
Remaco
4-Cores
AC
Cable
3-Cores AC Cable
A/V Control System
(Crestron, Panja)
5cm
5cm
Screen Frame = ScreenSize+ 5cm+ 5cm
c e
SreenSiz
Electronics
Screen
Control
(ESC)
M6
Countersunk
Screws
M5 Stopper
Screws
M6 Anchors
M6 Long Nuts
For Suspension from Ceiling
Insert these accessories in
between the indicated arrow.
Warning Caution with main supply and live wires. Install with qualified technician or trained
personnel.
Installation Guide (For PRO-1515 to PRO-2724)
CCOPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD Website: www.remacotech.com
Bracket
SS/ESC
V: 5.1
Universal Bracket can be used for any type of installation as shown below.
Use these holes
Wall Mount
Ceiling Mount Ceiling
Suspension
Pelmet Mount
Side
Pelmet
Mount
Ceiling
Recessed
Corner Mount Extension Mount (Wall)
5” to 9” Adjustable Extension
Mount (Optional)
10cm
10
cm
5” to 9”
UP DN N L
DN UP STOP COM
Connectors (N:Neutral) to Blue
(L:Live) to Red
(DN:Down) to Black
(UP:Up) to Brown
4-cores AC cable
For direct connection to AMX / Crestron or any A/V Control System.
No power / motor controller is required. Voltage signal, above 3Vdc will damage
this ESC. It works on momentary contact closure (dry contact, normally open,
voltage free) only. Contact closure must set close for 1.5 seconds.
Screen Frame
Universal Bracket
27
Power Drill Pin Punch Hammer
M6 Anchor
B) Drill Dia.8mm Holes to a depth 27mm. C) Insert M6 Anchor into the hole.
D) Use pin punch to expand the anchor.
A) Mark the bracket position with the help of universal bracket.
E) Terminate 4-cores AC cable as shown and also standard 3-cores AC cable.
STEP 1
STEP 2
STEP 3
Bottom Plan View
White Upper Limit
Lower Limit
F) To set screen to your desired “up” and “down” positions.
Adjust “ -” : screen roll away from frame
Adjust “ +” : screen roll into the frame
Adjust “ - “ : less screen drop
Adjust “ +“ : more screen drop
Screen Frame
STEP 4
8mm Drill
PCB
-
+
+
-
(Note: Do not drill too deep)
Board
Important Notes:
All screens are thoroughly inspected and fully tested operational in factory.
We accept no liability whatsoever for any losses due to improper wiring, installation, operation, or any unauthorized alternation at the point of installation.
All trademarks contained in this installation guide are the property of their respective owners.
End
CCOPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD Website: www.remacotech.com
ESC
Hook on (NOT slide in)
WARNING!
!
STOP
Important Note
The upper limit and lower limit of the screen had been preset in factory. Any adjustment to these 2 limit
switches may cause demages to the screen fabric. If adjusted, it will cause the following problems:
a) The screen will roll into the frame and stop by force and not by the Upper Limit switch.
This will cause overheating of motor which unable the screen to operate properly.
b) The depression of the bottom bar onto the fabric will cause horizontal mark on screen surface.
c) Adjusting the Lower Limit of the screen any lower than beyond the STOP sticker may cause the fabric
to drop off
Disclaimer
no responsibility for any damages to it. Please consult us if it is necessary to do any adjustment to the
limit switch.
Any adjustment to these 2 limit switches will void the warranty for the screen and Remaco will hold
Yellow
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Remaco Zubehör Handbücher
