Remington X6 POWER-X Series Bedienungsanleitung

X6 POWER-X SERIES

HAIR CLIPPER

5 YEAR WARRANTY HC6000AU

To register your product go to

www.remington-products.com.au

www.remington.co.nz

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should

always be observed, including the following.

For additional protection, the installation of a residual current

device (rcd) having a rated residual operating current not

exceeding 30 mA is advisable in the electrical circuit supplying

the bathroom. Ask your installer for advice

KEEP AWAY FROM WATER

WARNING - TO REDUCE THE RISK OF BURNS, ELECTROCUTION AND

FIRE OR INJURY TO PERSONS

DANGER - As with most electrical appliances, electrical parts are

electrically live even when the switch is off.

• Do not place or store the appliance or charging adaptor where it can

fall or be knocked into a sink or bath.

• Do not place in or drop into water or any other liquid.

• If an appliance falls into water, “unplug it” immediately. Do not reach

into the water.

• Do not use while bathing or in the shower.

• Unplug and switch off this appliance before cleaning it.

• Use this appliance only for its intended use as described in this

manual.

• Do not use attachments not recommended by Remington.

• Never drop or insert any object into any opening of this appliance.

• Keep the cord away from heated surfaces.

• Do not use this appliance with a damaged or broken trimming unit as

injury may occur.

• Always store the charging adaptor in a moisture-free location.

• For household use only.

• This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

• Keep the appliance and the power cord away from the edge of table

or countertops and out of reach of children and persons with reduced

physical, sensory or mental capabilities.

• This appliance is not a toy. Children shall be supervised to ensure they

do not play with the appliance.

• Do not use on people who are asleep.

• Never operate this appliance if it has a damaged cord or plug, if it is

not working correctly, if the charging adaptor has been damaged or

dropped into water.

• Do not use an extension cord or a voltage converter with this

appliance.

• Do not wrap the cord around the appliance.

• This appliance should be supplied with approved safety isolating

adaptors PA-0510A (for Australia) with the output capacity of 5.0V dc;

1A (adaptor output).

WARNING - KEEP THE APPLIANCE DRY

Remington strongly recommends that an approved Safety Switch

(Residual current device) be installed to protect all bathroom

power outlets. Ask an electrical contractor for advice.

SAVE THESE INSTRUCTIONS

HC6000AU X6 POWER-X SERIES HAIR CLIPPER

USE AND CARE MANUAL

Thank you for purchasing your Remington®X6 Power-X Series Hair Clipper.

Inside this manual you will find instructions on using and caring for your

new hair clipper.

KEY PARTS

1. Blade set

2. On/Off/Turbo Switch

3. Length adjustment dial

4. Length setting window for

25 - 35 mm comb

5. Length setting window for

14 - 24 mm comb

6. Length setting window for

3 - 13 mm comb

7. Digital Display

8. Charger connector

9. 25 - 35 mm comb

10. 14 - 24 mm comb

11. 3 - 13 mm comb

12. Micro fade adjustable comb

Not Shown:

• Cleaning brush

• Oil bottle

• Pouch

• Power adapter

• USB cable

ABOUT YOUR HAIR CLIPPER

HC6000AU SPECIFICATIONS

Power System Cord/Cordless

Full Charge Time 2 Hours

Runtime 90 Minutes

Indicators Digital Fuel Gauge

Voltage Type (adaptor voltage type) Worldwide 100-240V

CHARGING

• Before using your hairclipper for the first time, charge for 2 hours.

• Plug the adaptor into your hair clipper and then plug the charging

adaptor unit into a 100-240 volt domestic power outlet. Check to

ensure that the hair clipper On/Off switch is OFF.

• If the product is not going to be used for an extended period of time (2

- 3 months), unplug it from the mains and store. Fully recharge your

hairclipper when you would like to use it again.

• Allow 2 hours for a complete charge.

• Use the hair clipper only with the charging adaptor supplied.

DIGITAL DISPLAY

• The device features a digital fuel gauge to show remaining charge and

charging status:

During charging:

When the unit is plugged in, the corded indicator

icon will show ( ). With the device turned off and

connected to the charger, the display will light up in

a rotating pattern during charging.

Once charged the display will show 90 and the

corded indicator icon ( ).

During corded use:

When the unit is plugged in, the corded indicator

icon will show ( ). Normal operating speed:

When the unit is plugged in, the corded indicator

icon will show ( ). Turbo mode:

During cordless use:

The display will show the remaining run time in

minutes. When the run time reaches 5 minutes it

will flash.

When in turbo mode, the display will be the same

as above with the turbo symbols (>>>)

• The clipper comes with a quick charge function, 10 minutes charging

will give an emergency burst of run time.

CHARGING VIA STANDARD ELECTRICAL SOCKET

• Ensure the product is switched off.

• Connect the charging adaptor to the product and then to the mains.

USB

• Connect Micro USB to the appliance, and the USB connector to any

standard USB port or charger

• Product will only charge through USB and will not run in corded mode.

CORDED USE

• Connect the charging adaptor to the product then to the mains.

Note: Extended mains only use will result in the reduction of the battery life.

CORDLESS USE

• When the product is switched on and fully charged it can be used in

cordless mode for up to 90 minutes.

CLEANING AND MAINTENANCE

• Your clipper is fitted with high quality blades.

• To ensure long lasting performance of your clipper, clean the blades

and unit regularly.

• Always keep the attachment guide comb on the trimmer blade.

AFTER EACH USE

• Ensure the appliance is switched off and unplugged from the charging

adapter before cleaning.

• Brush the accumulated hair from the blades and body of the clipper.

Do not submerge the clipper in water.

• To clean unit, wipe with a damp cloth and dry immediately.

• Place a few drops of cutter or sewing machine oil onto the blades.

Wipe off excess oil.

WASHABLE BLADE CLEANING

• This clipper is fully washable and therefore

can be rinsed under a running tap.

• To remove the blades ensure the unit is

switched off. Push the blade set away from

the clipper body using your thumb (Fig A).

• To reattach once the blades are cleaned

and dry, align the bottom of the blade with

the bottom blade housing tab and slide the cartridge back into place

until you hear a click.

CLEANING CAUTIONS

• Do not use harsh or corrosive cleaners on the units or their blades.

• Ensure the appliance is switched off and unplugged from the main

outlet before cleaning.

Storage: Always store this appliance and cord in a moisture-free area. Do

not wrap the cord around the appliance. Do not store in temperatures above

60ºC.

INSTRUCTION FOR USE

BEFORE STARTING THE CUT

• Make sure your clipper is operating correctly. Inspect the hair clipper

making sure that it is free from hair and dirt.

• Place a cape around the neck of the person whose hair is being

trimmed or cut.

• Seat the person so that their head is approximately at your eye level.

• Before cutting, always comb the hair so it is tangle free and dry.

• Hold the hair clipper in the palm of one hand and with your thumb

resting firmly on the top of the hair clipper. This grip provides

comfortable cutting control.

TO ATTACH A COMB

• Hold the comb with its teeth upward.

• Align the legs of the comb with the holes in the top of the clipper on

each side of the blade and slide the legs into the trimmer until they

click (Fig B).

• To remove, firmly pull the comb straight up away from

the clipper.

SETTING THE LENGTH OF CUT

• Your clipper comes with three adjustable combs 3 to 13

mm, 14 to 24 mm and 25 to 35 mm.

• These provide a length of cut that can be adjusted

between 3 and 35 mm in increments of 1 mm.

1. Select the comb that fits the range of cut you want to achieve.

2. Fit the comb then rotate the length adjustment dial until the length you

want appears in the length selection window for that comb.

3. The length setting colour on the wheel matches the length marker

colour on the comb.

4. For example, if you want a cut length of 20 mm, fit the 14 to 24 mm

comb then turn the dial until 20 appears in the length setting window

for the 14 - 24 mm comb.

5. Use the clipper without any fixed combs for trimming hair close to the

skin.

6. This will trim hair to 1mm, holding the clipper so the blades are

perpendicular to the skin will trim hair to 0.5mm.

INSTRUCTIONS FOR CUTTING HAIR

• Turn the product on using the on/off switch.

• For even cutting, allow the comb attachment/blade to cut its way

through the hair. Do not force it through quickly. If you are cutting for

the first time, start with the maximum guide comb, until you know how

short you would like your hair to be.

• The comb guide lengths described for use in the steps below are an

example only, if you want a longer or shorter hair cut you will need to

adjust the comb guide lengths to suit your requirements.

Step 1 - Nape Of The Neck

• Use 3mm or 6mm guide comb.

• Hold the hair clipper with the blade teeth pointing upwards. Begin

starting at the centre of the head at the base of the neck.

• Slowly lift the hair clipper, working upwards and outwards through the

hair, trimming just a little at a time.

Step 2 - Back Of The Head

• With the comb set at 12 mm or 18 mm, cut the hair at the back of the

head.

Step 3 - Side Of The Head

• With the comb set at 3 mm or 6 mm, trim sideburns.

• Then change to the longer 9mm guide comb and continue to cut to the

top of the head.

Step 4 - Top Of The Head

• Use the longer length comb attachment and set it to 24 mm or 27 mm

then cut hair on top of the head against the direction in which the hair

normally grows.

• For longer hair on top, use the longer length comb attachment (25 –

35 mm) to achieve the desired style.

• Always work from the back of the head.

Step 5 - The Finishing Touches

• Use the hair clipper without an attachment comb for close trimming

around the base and sides of the neck.

• To produce a clean straight line at the sideburns, reverse the clipper.

Place the reversed hair clipper at right angles to the head, tips of the

blades lightly touching the skin and then work downwards.

MICRO FADE ADJUSTABLE COMB

• The micro fade adjustable comb allows precision cutting in the 1 to

5mm range.

• Use the adjustment dial to set the comb to the desired length.

AUTO TURBO SYSTEM

• When switched on, your clipper runs in normal mode. The Auto Turbo

feature will automatically activate when the clipper senses it needs

more power.

• To run in Turbo mode, slide the on/off switch to the turbo position.

BATTERY REMOVAL

We strongly recommend that a professional removes the rechargeable

battery. Parts of the shaver case, and tools have sharp edges and may

cause injury if not handled correctly.

• The battery must be removed from the appliance before it is scrapped.

• The appliance must be disconnected from the supply mains when

removing the battery.

• Ensure that the battery is fully discharged. To do this, operate the

device until it stops.

• Pry off and remove the top panel.

• Using a small screwdriver, unscrew 2 screws from the top housing.

• Pry off and remove the top housing.

• Unscrew the 3 screws on the inner housing then remove the inner housing.

• Remove the battery assembly.

• Cut the battery tabs and remove the battery from bracket.

• The battery must be disposed of at an appropriate official recycling/

collection point.

• Do not attempt to operate the trimmer once you have opened it.

DISPOSAL/RECYCLING

Legislation in some localities mandates that e-waste (anything with a plug,

battery or cord) is disposed of through controlled recycling facilities and

must not be disposed of in general household waste. For more information

about recycling of electrical and battery operated appliances, please

contact your local council or your local household waste disposal service.

This product is not suitable for bath or shower.

This product conforms to radio frequency interference requirements

Any product purchased and used commercially carries a limited 90 Day Warranty.

Andere Handbücher für X6 POWER-X Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Remington Haarschneider Handbücher

Remington

Remington HC825AU Bedienungsanleitung

Remington

Remington HC6550 Bedienungsanleitung

Remington

Remington Shortcut clipper SCC-100R Bedienungsanleitung

Remington

Remington HC535 Bedienungsanleitung

Remington

Remington HC1080 Bedienungsanleitung

Remington

Remington HC5800 Bedienungsanleitung

Remington

Remington HC4250AU Bedienungsanleitung

Remington

Remington BHT2000A Bedienungsanleitung

Remington

Remington HC3000GP Bedienungsanleitung

Remington

Remington HC335 Bedienungsanleitung

Remington

Remington QuickCut Pro Bedienungsanleitung

Remington

Remington HC335 Bedienungsanleitung

Remington

Remington X4 Power-X Series Bedienungsanleitung

Remington

Remington HC6525 Bedienungsanleitung

Remington

Remington NE100C Bedienungsanleitung

Remington

Remington HC-5850 Bedienungsanleitung

Remington

Remington Pro Power Alpha Bedienungsanleitung

Remington

Remington HC4000AU Bedienungsanleitung

Remington

Remington Classic HC450 Bedienungsanleitung

Remington

Remington ProPower HC7130 Bedienungsanleitung

Remington

Remington X3 POWER-X Series Bedienungsanleitung

Remington

Remington Omniblade HG1000 Bedienungsanleitung

Remington

Remington Indestructible HC5880 Bedienungsanleitung

Remington

Remington HC366AU Bedienungsanleitung

Beliebte Haarschneider Handbücher anderer Marken

Clatronic

Clatronic HSM 800 Bedienungsanleitung

Mellerware

Mellerware MACRO ALDANY MA20001 Bedienungsanleitung

VALERA

VALERA X-Master 652 Bedienungsanleitung

Wahl

Wahl 1870Li Bedienungsanleitung

Lister

Lister Legend Bedienungsanleitung

Philips

Philips HC5440/80 Bedienungsanleitung

Andis

Andis MBA 23125 Bedienungsanleitung

Philips

Philips Philishave HQC488/61 Bedienungsanleitung

Shear Magic

Shear Magic Nifty 1800 Bedienungsanleitung

Philips

Philips QC5390 Bedienungsanleitung

Andis

Andis US-1 Kurzanleitung

Panasonic

Panasonic EH-KA81 Bedienungsanleitung

Philips

Philips HC5450 Bedienungsanleitung

Andis

Andis US-1 Montageanleitung

Andis

Andis ML Montageanleitung

O'Barber

O'Barber MINI SLIDE Bedienungsanleitung

Oster

Oster 76110 Bedienungsanleitung

Hyundai

Hyundai HC 420 Bedienungsanleitung