Riccar 1500P Bedienungsanleitung

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 2

When using an electrical appliance, basic precautions should always be followed, including the

following :

WARNING -

To reduce the risk of fire, electric shock, or injury :

11. Do not leave appliance when plugged in. Unplug from outlet when not in use and before

servicing.

12. Do not use outdoors or on wet surfaces.

13. Do not allow to be used as a toy. Close attention is necessary when used near children.

14. Use only as described in this manual. Use only manufacturer's recommended attachments.

15. Do not use with damaged cord or plug. If appliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped into water, return it to a service center.

16. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around

sharp edges or corners. Do not run appliance over cord.

Keep cord away from heated surfaces.

17. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

18. Do not handle plug or appliance with wet hands.

19. Do not put any object into openings. Do not use with any opening blocked:

keep free of dust, lint, hair, and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

11. Turn off all controls before unplugging.

12. Use extra care when cleaning on stairs.

13. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where

they may be present.

14. This appliance is intended for household use only and not for commercial or industrial use.

15. Do not operate the vacuum if :

- the power cord is damaged.

- the hose shows visible signs of damage.

16. Do not use without vacuum bag and/or filters in place.

17. Hold plug when rewinding the cord into cord reel. Do not allow plug to whip when rewinding.

18. The hose contains electrical wires. Do not use if damaged, cut or punctured.

Avoid picking up sharp objects.

19. To reduce the risk of electric shock, this appliance has a polarized plug.

20. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

21. Always turn off this appliance before connecting or disconnecting motorized nozzle.

22. Use only with motorized nozzle model RPB-220.

SAVE THESE INSTRUCTIONS

Read All Instructions Carefully Before Using This Appliance

IMPORTANT SAFETY INSTRUCTIONS

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 3

CONTENTS

DESCRIPTION AND USING ............................................. 4~5

HOW TO POWER NOZZLE.............................................. 6~9

SAFETY PRECAUTIONS.................................................... 10

REPLACING BAGS & FILTERS.......................................... 11

TROUBLESHOOTING GUIDE ............................................ 12

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 4

DESCRIPTION AND USING

CLEANING TOOLS

FULL BAG INDICATOR

HOSE HANDLE

How to check the FULL BAG INDICATOR:

• If the red indicator appears:

- Empty the vacuum bag.

- If the vacuum bag isn’t full and the full bag indicator is red, check

the hose for a clog.

• When cleaning with a tool (dusting brush,upholstery nozzle,crevice

tool,floor tool), the red indicator may appear. In this case, continue

cleaning.

HOSE ADAPTER

• When separating the hose from the body, pull the

hose adapter while pressing the buttons.

SUCTION CONTROL

POWER NOZZLE

SWITCH

HIGH

LOW

OFF

Dusting Brush

Power Nozzle

Upholstery Nozzle

HARD SURFACE FLOOR TOOL

•For use on tile, hard wood, and

linoleum floors

•3n1 multi-purpose tool

Insert end of wand into either end of

tool for multiple cleaning functions.

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 5

CLEANING TOOLS

CORD REWIND

POWER CONTROL

MAX

STOP

ADAPTER

hose from the body, pull the

essing the buttons.

STORAGE

ON/OFF SWITCH

•Insert the brush holder

on the neck of the wand

into the groove.

Adapter button

Crevice Toolstery Nozzle

Power control is

on the canister body

not the handle

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 6

HOW TO USE POWER NOZZLE

OPERATION

1. Turning on the Power Nozzle

The power nozzle can only be turned on if the

canister is also turned on (canister on / off

switch is located on the main body). The

power nozzle on / off switch is located on the

handle. Simply press the switch forward to

engage the power nozzle.

To achieve best cleaning results, slowly pass

the power nozzle back and forth over the

carpet or floor.

2. Using the Power Nozzle

After turning on the canister and power nozzle,

release the wand by pressing the left pedal on the

back side of the power nozzle (see diagram 3)

3. Remove / Insert the Wand From The Power

Nozzle

Removing the wand from the power nozzle

allows you, for example, to use cleaning tools

for baseboard or ceiling cleaning. To do this,

first turn the power nozzle and canister off.

Then, press the wand release collar (see

diagram 5) and pull the wand out. To reinsert

the wand into the power nozzle, simply press

the wand back into the neck of the power

nozzle. The wand will then "click" back into

place.

4. Carpet Height Adjustment

Your power nozzle has six different settings to

clean a variety of carpet types and floor

surfaces. To adjust the carpet height setting of

the power nozzle, press the right pedal located

on the back of the power nozzle (see diagram

6). Each press of this pedal will adjust the

height to the next carpet height position.

To determine which setting you are currently

on, locate and look through the height indicator

window on the top of the unit (see diagram 7).

You will see one of the six settings as

mentioned earlier and detailed below:

Setting: Intended Use:

1. XHI Very plush carpet

2. HI Plush carpet

3. Auto General carpet thickness or bare

floors

4. MED Medium pile carpet

5. LO Low pile carpet

6. XLO Indoor/Outdoor carpet

Carpet Height Notes: When using the power

nozzle, start on the "auto" setting. If pushing the

power nozzle forward feels sluggish or hard to

push, then adjust to a higher setting (i.e. HI or

XHI). If the power nozzle feels very easy to push,

you may want to lower the power nozzle for more

effective cleaning. The "Auto" setting is the

recommended setting for hard floor surfaces (i.e.

tile, vinyl, wood).

Diagram 3

Diagram 6 Diagram 7

Diagram 5

Diagram 4

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 7

OPERATION

5. Warning Light

Your power nozzle comes equipped with a

circuit breaker safety system that protects it

from a jammed power nozzle situation.

Common items that cause jammed brushrolls

include socks, excessive threads, corners of

area rugs, etc. The warning indicator light on

top of the unit (see diagram 8) will change from

green to red should this condition occur.

If the circuit breaker trips:

a. Turn off the vacuum cleaner and power brush

then unplug the power cord.

b. Remove the object preventing the brushroll

from turning.

c. Locate the circuit breaker switch on the back of

the power nozzle and press it to reset the

breaker (see diagram 9).

d. When the unit is turned back on, the warning

light should be green and ready to go. If the

breaker trips again, repeat steps a-c again to

correct the problem.

If this does not correct the problem, contact

your authorized vacuum cleaner retailer for

further assistance.

MAINTENANCE AND CARE

1. Removing the Brushroll

IMPORTANT: Before performing any

maintenance work on the power nozzle,

always unplug the vacuum cleaner and

disconnect the wand.

Your brushroll may need to be removed at

times, for example, to cut threads that have

become tangled around the brushroll or to

replace the belt (see "Replacing the Belt").

To remove the brushroll, turn the unit over and

lift off the metal bottom plate by first

unscrewing the two bottom plate screws

located by the rear wheels (see diagram 10).

Pull out the belt cover guard (see diagram 11)

and pull the brushroll out.

To reinstall the brushroll, reinsert the brushroll

back into the unit (make sure the belt is

attached properly). Next, insert the belt cover

guard. Then, place the metal bottom plate

back onto the unit (insert the front end of the

bottom plate first). Re-insert the two bottom

plate screws and secure.

Diagram 8

Warning Light Circuit Breaker Switch

Diagram 9

Bottom

Plate Screws

Diagram 10 Diagram 11

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 8

MAINTENANCE AND CARE

2. Replacing the Power Nozzle Belt

IMPORTANT: Before performing any

maintenance work on the power nozzle,

always unplug the vacuum cleaner and

disconnect the wand.

To replace the power nozzle belt, you must

first remove the brushroll (see "Removing the

Brushroll"). Locate and discard broken belt.

To install new belt, locate the power nozzle

motor pulley and loop the belt around it (see

diagram 12). Place the other end of the belt

around the brushroll making sure the belt is

seated in the "belt groove" of the brushroll (see

diagram 13). Insert the brushroll back into the

brushroll tray and place the belt guard back

into position (see diagram 11). Place the

metal bottom plate back onto the unit (insert

the front end of the bottom plate first). Re-

insert the two bottom plate screws and secure.

3. Replacing the Bulb

IMPORTANT: Before performing any

maintenance work on the power brush, always

unplug the vacuum cleaner and disconnect the

wand.

Turn the power brush over and remove the

bottom plate by first unscrewing the two

bottom plate screws located by the rear

wheels (see diagram 10). Locate and remove

the two top cover screws (see diagram 14).

Turn the power brush back over, push the

power brush neck flat, and remove the top

cover (see diagram 15). Simply pull the bulb

out (no twisting) and reinsert a factory-

authorized bulb. Place the top cover back on

the unit, turn the machine over and re-insert

the two top cover screws. Reinstall the bottom

plate.

Diagram 12 Diagram 13 Diagram 14 Diagram 15

Belt Top Cover

Screw

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 9

DIAGRAM 1 REAR VIEW OF POWER WAND AND NOZZLE ASSEMBLY

DIAGRAM 2 FRONT VIEW OF POWER WAND AND NOZZLE ASSEMBLY

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 10

•Do not vacuum areas which contain moisture

or water, flammable matter, needles, pins, razor

blades, matches, cigarettes, etc., since they

may damage the vacuum or vacuum bag.

•Make sure a vacuum bag and filters are always

inserted.

•When rewinding the power cord, hold the plug

before pressing the cord rewind button to

prevent the cord from whipping.

•This product is equipped with a polarized

alternating current line plug (a plug having one

blade wider than the other). This plug fits into

the power outlet only one way.

This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing

the plug. If the plug should still fail to fit, contact

an electrician to replace the obsolete outlet.

Do not defeat the safety purpose of the

polarized plug.

This vacuum cleaner should be used for normal, dry household dust and dirt.

The manufacturer cannot be held responsible for any damage caused by use or operation of the vacuum

contrary to these instructions.

If the vacuum is wrongly operated for a purpose other than that for which it is intended, no liability can be

accepted for any possible damage.

SAFETY PRECAUTIONS

R1500P(EN-TACONY)-9.3 2004.9.3 9:55 AM 11

Inhaltsverzeichnis

Andere Riccar Staubsauger Handbücher

Riccar

Riccar RC-1500P Bedienungsanleitung

Riccar

Riccar Radiance RAD.5 Bedienungsanleitung

Riccar

Riccar Hybrid Central Vac Bedienungsanleitung

Riccar

Riccar R40P Bedienungsanleitung

Riccar

Riccar Butler Bedienungsanleitung

Riccar

Riccar Starbright Bedienungsanleitung

Riccar

Riccar Vibrance Bedienungsanleitung

Riccar

Riccar Vibrance VIB Bedienungsanleitung

Riccar

Riccar SupraLite R10S Bedienungsanleitung

Riccar

Riccar 8000 series Bedienungsanleitung

Riccar

Riccar SUPRAQUIK RSQ1 Bedienungsanleitung

Riccar

Riccar 1700 Bedienungsanleitung

Riccar

Riccar Pizzazz Bedienungsanleitung

Riccar

Riccar SUPRAQUIK RSQ1 Bedienungsanleitung

Riccar

Riccar 1800 Bedienungsanleitung

Riccar

Riccar 4000 Series Bedienungsanleitung

Riccar

Riccar OMNICLEAN OC1 Bedienungsanleitung

Riccar

Riccar 1800 Bedienungsanleitung

Riccar

Riccar RPB-F Bedienungsanleitung

Riccar

Riccar 2000 Series Bedienungsanleitung

Riccar

Riccar VOLT Bedienungsanleitung

Riccar

Riccar RC-1700S Bedienungsanleitung

Riccar

Riccar 2000 Series Bedienungsanleitung

Riccar

Riccar Carpet Keeper Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch