Riccar SUPRALITE RSL1A Bedienungsanleitung

O w n e r ’ s M a n u a l

RSL1A, RSL3, RSL3C & RSL4

Congratulations!

You have purchased a vacuum cleaner that will provide years

of efﬁcient, dependable service. Your Riccar vacuum cleaner is

made using high quality materials and superior workmanship.

Please read these operating instructions carefully before you

use your vacuum.

Riccar is a nationwide company with over 600 Authorized

Retailers to serve you.

To locate your closest Authorized Retailer regarding warranty

work, questions, bags and accessories, please call

1-888-6-RICCAR

or visit our website

www.riccar.com

IMPORTANT:

To activate your warranty, within 30 days of purchase please ﬁll

out and return the warranty postcard OR ﬁll out the warranty

form online at www.riccar.com.

Please ﬁll out warranty information located on page 18 and keep

it for your records.

Key Replacement Parts

Genuine SupraLite HEPA Vacuum Bags: RSLH-6

Genuine SupraLite Vacuum Bags: RSL-6

Genuine SupraLite Vacuum Belt: RBS-2

Contents

Getting Started

Important Safety Instructions 5

Wire and Grounding Instructions 6

Assembling the Vacuum 7-9

Vacuum Features

On/Off Switch 11

Edge Cleaning 11

Automatic Carpet Height Adjustment 11

Bare Floor Cleaning 11

How To

Change the Vacuum Bag 12

Remove/Install the Bottom Plate 13

Change the Belt 14

Replace the Headlight Bulb 15

Replace the Squeegee 16

Reset the Circuit Breaker 16

Owner’s Information 18

For Best Performance 18

Warranty 19

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including

the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

The manufacturer cannot accept responsibility for damage

caused when the appliance is not used according to the

instructions, or for uses other than those for which it

was intended.

To reduce the risk of fire, electric shock or injury:

• Do not leave appliance when plugged in.

Unplug from outlet when not in use and

before servicing.

• WARNING: ELECTRIC SHOCK COULD

OCCUR IF USED OUTDOORS OR ON

WET SURFACES.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Use only as described in this manual.

Use only manufacturer’s recommended

attachments.

• Do not use with damaged cord or plug. If

appliance is not working as it should, has

been dropped, damaged, left outdoors,

or dropped into water, return it to your

Authorized Retailer for service.

• Do not pull or carry by cord, use cord as

a handle, close a door on the cord, or pull

cord around sharp edges or corners. Do

not run appliance over cord. Keep cord

away from heated surfaces.

• Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with

wet hands.

• Do not put any object into openings. Do

not use with any opening blocked; keep

free of dust, lint, hair and anything that

may reduce air ﬂow.

• Keep hair, loose clothing, ﬁngers and all

parts of body away from openings and

moving parts.

• Do not pick up anything that is burning or

smoking, such as cigarettes, matches or

hot ashes.

• Do not use without vacuum bag in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up ﬂammable or

combustible liquids such as gasoline or

use in areas where they may be present.

• Do not attempt to service the unit while

appliance is plugged in.

• Do not use vacuum to pick up water or

any wet materials.

SAVE THESE INSTRUCTIONS.

WARNING:

Polarization instructions

Models RSL1A, RSL3 and RSL4

To reduce the risk of electric shock, this appliance is equipped with a polarized alternating

current line plug (a plug having one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into

the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician

to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.

Assembling the Vacuum

Important Note:

Under no circumstances should you plug in the

vacuum cleaner prior to complete assembly.

Model RSL1A

The vacuum cleaner handle is packed as a

separate component that requires assembly.

Installing the handle:

1. Release the handle bracket from the handle

tube by removing the two screws (figure 1).

2. Place handle onto the handle tube, aligning

holes with pegs (figure 2).

Fig. 1

Fig. 2

RSL1A Handle

RSL3, RSL3C and RSL4 Handle

Power cord

Cloth bag

Nozzle

Quick Cord Release

Commercial model RSL3C only

This vacuum cleaner must be grounded. If it should malfunction or break down, grounding

provides a path of least resistance for electric current to reduce the risk of electric shock.

This vacuum cleaner is equipped with a cord having an equipment-grounding conductor

and grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

This vacuum cleaner is for use on a nominal 120-volt circuit and has a ground plug

(see illustration). Make sure that the vacuum is connected to an outlet having the same

configuration as the plug. No adapter should be used with this vacuum.

Grounded

Outlet

Grounding

Grounded

Outlet Box

WARNING – Improper connection of

the equipment-grounding conductor

can result in the risk of electric shock.

Check with a qualified electrician or

service person if you are in doubt

as to whether the outlet is properly

grounded. Do not modify the plug

provided with the vacuum – if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Assembling the Vacuum

Model RSL1A cont.

3. Place the handle bracket back into position

(figure 3).

4. Secure with two screws removed in step 1.

Postioning the power cord:

1. Loosen, but do not remove, the screw holding

the upper cord hook (figure 4).

2. Position the cord between the cord hook and

the vacuum tube (figure 5). Re-tighten the

screw.

3. Once the cord is secured by the cord hook,

proceed with wrapping the cord.

Fig. 3

Fig. 4

Fig. 5

Assembling the Vacuum

Models RSL3, RSL3C and RSL4

The vacuum cleaner handle is packed as a

separate component that requires assembly.

Installing the handle

1. Release the handle bracket from the handle

tube by removing the two screws (figure 6).

2. Place handle onto the handle tube, aligning

holes with pegs (figure 7).

3. Place the handle bracket back into position

(figure 8).

4. Secure with two screws removed in step 1.

5. Thread cord through cord guides and proceed

with wrapping the cord (figure 9a & 9b).

Fig. 6

Fig. 7

Fig. 8

Fig. 9a Fig. 9b

Vacuum Features

On/Off Switch

NOTE: There are three different on/off switch

configurations depending on the model you

own. Identify your vacuum cleaner model and

see the corresponding on/off switch operating

instructions below.

RSL1A – On/Off switch on base:

Locate the switch on the back side of the nozzle

to the left of the handle tube (see figure 10).

Simply press the switch with your foot to turn

the vacuum on or off.

Machine should be turned off before returning

handle to full upright position. Always turn the

vacuum cleaner off before unplugging it from the

electrical outlet.

RSL3 and RSL3C –

On/Off switch on handle:

Locate the switch on the top of the vacuum

handle. Using your thumb, push the switch

forward to turn the machine on and pull

the switch backward to turn the machine

off (see figure 11).

Machine should be turned off before returning

handle to full upright position. Always turn the

vacuum cleaner off before unplugging it from the

electrical outlet.

RSL4 – On/Off two speed switch on handle:

The switch for this model, located on the

vacuum handle, is a three-way switch. The

middle position is the off setting, the rear

position is the on setting and the forward

position is for maximum power (see figure 12).

Use the maximum power setting for carpet

cleaning and the on setting for cleaning bare

floors and throw rugs.

Fig. 10

Fig. 11

Fig. 12

Vacuum Features

On/Off two speed switch on handle cont.

Pull the switch backward to turn the vacuum on.

Push the switch halfway back to turn the vacuum

off. Push the switch all the way forward to use the

maximum power setting.

Machine should be turned off before returning handle

to full upright position. Always turn the vacuum cleaner

off before unplugging it from the electrical outlet.

Edge Cleaning

The edge cleaning feature provides improved cleaning

near walls and stationary furniture. For maximum edge

cleaning, place the left side of the nozzle against the

wall or stationary furniture.

Automatic Carpet Height Adjustment

Your SupraLite vacuum is designed with an automatic,

self-adjusting nozzle. No manual adjustments are

required. The height of the nozzle is instantly and

automatically adjusted to the flooring surface. This self-

adjusting feature allows the nozzle to float evenly over

all flooring surfaces.

Bare Floor Cleaning - Model RSL4 Only

The RSL4 model SupraLite comes equipped with a

squeegee on the bottom of the vacuum to improve its

effectiveness in cleaning bare floors. When cleaning

tile, hardwood, linoleum, etc., use the on setting,

as opposed to the maximum power setting, for

best results. (See figure 13)

Fig. 13

How To

Change the vacuum bag

CAUTION: First, unplug the vacuum cleaner from

the electrical outlet.

1. Unzip outer cloth bag (figure 14).

2. Remove used bag by pressing the bag holder

tab and pulling bag off vacuum (figure 15).

Discard used bag.

3. To install new bag, position the bottom of the

bag collar into the bag collar holder (figure 16).

4. Push the top of the bag collar inward until

the collar “snaps” into place under the bag

holder tab.

5. Zip the outer cloth bag closed.

Fig. 14

Fig. 15

Fig. 16

How To

Remove/install the bottom plate

CAUTION: First, unplug the vacuum cleaner

from the electrical outlet.

To remove bottom plate:

1. After unplugging the power cord, turn

the vacuum cleaner over, exposing the

underside.

2. Press the two holding tabs inward (figure

17) releasing the bottom plate. Remove

the bottom plate.

To install bottom plate:

1. Install bottom plate, making sure

bottom plate hinges are in place before

setting the plate (figure 18).

2. Press plate into position until the plate

“clicks” on both sides.

Fig. 17

Fig. 18

How To

Change the belt

CAUTION: First, unplug the vacuum cleaner

from the electrical outlet.

1. Turn the unit over and remove the

bottom plate (see “How to Remove

Bottom Plate”).

2. Remove the brushroll and the worn or

broken belt from the brushroll pulley and

the motor drive shaft (figure 19).

3. Loop the new belt around the

motor drive shaft and the brushroll

(figure 20).

4. Reinstall the brushroll back into the

housing. Turn the brushroll by hand,

making sure the belt is not twisted

and all rotating parts move smoothly

(figure 21).

5. Reinstall the bottom plate (see “How to

Install Bottom Plate”).

NOTE: To ensure maximum cleaning

efficiency, the belt should be checked

regularly to be sure it is in good condition.

Check to see if the belt is stretched,

cracked, or if excessive slipping is occuring.

Replace if needed.

Fig. 19

Fig. 20

Fig. 21

How To

Replace the headlight bulb

WARNING: To reduce the risk of electric

shock and injury from moving parts, unplug

vacuum before cleaning or servicing.

1. First remove the nozzle housing. Turn

the unit over to expose the underside.

Locate the two main nozzle screws

(figure 22) and remove both. Turn the

unit right side up. Locate the two nozzle

tabs on the back of the unit (figure 23)

and unlatch the nozzle housing. (Note: It

is easier to remove the nozzle when the

vacuum is lying flat on its back.) Lift the

nozzle housing off the unit to expose

the light bulb.

2. Remove bulb by pulling it straight out of

the light socket (figure 24).

3. To install new bulb, simply reinsert the

bulb into the light socket.

4. Place nozzle housing back onto unit with

the front side of the nozzle set into place

first (figure 25) then press the nozzle

downward until nozzle “clicks” into place

on both sides. Turn unit over and reinsert

two main nozzle screws.

Fig. 22

Fig. 23

Fig. 24

Fig. 25

How To Notes

Replacing the squeegee -

Model RSL4 Only

If your squeegee splits or begins to look

worn, simply remove the worn squeegee

from its track and slide a new one into

the track (figure 26). If you have trouble

installing the new squeegee, please see

your Authorized Retailer.

Reset the circuit breaker

Your vacuum features a circuit breaker

to protect the machine against damage

due to a surge in the electrical current.

Electrical surging can be a result of, though

not limited to, a jammed brushroll (i.e.

vacuuming up a sock or throw rug) or a

jammed motor fan.

Should your SupraLite vacuum cleaner

experience a jammed brushroll with the

circuit breaker tripping, first press the on/off

button to the off position and unplug the

unit. Inspect the brushroll by removing the

bottom plate (see “How to Remove Bottom

Plate”) and remove any debris which may

be causing the jam. Reinstall the bottom

plate (see “How to Install Bottom Plate”),

reset the circuit breaker by pressing the

Circuit Breaker Reset Button (figure 25),

plug in power cord, and turn unit on. If

the unit fails to turn on, return it to an

Authorized Riccar Retailer for service.

Fig. 27

Circuit breaker

reset button

Fig. 26

Warranty

What is Covered:

This warranty covers any defects in material and workmanship in your new

Riccar vacuum and applies exclusively to the original purchaser.

How Long Coverage Lasts:

Warranty coverage for Riccar SupraLite household model vacuums lasts two

years. Household models used commercially are only warranted for 90 days.

Warranty coverage for Riccar SupraLite Commercial model vacuums

lasts one year.

What is Not Covered:

• Damage to the vacuum which occurs from neglect, abuse, alterations,

accident, misuse or improper maintenance.

• Normal replacement items: belts, light bulbs, squeegees and

disposable bags.

What Riccar Will Do:

This warranty provides, at no cost to you, all labor and parts to place this

vacuum in correct operating condition during the warranted period.

How to Get Service:

Warranty service can only be obtained by presenting the vacuum to an

Authorized Riccar Retailer. A proof-of-purchase and product serial number

will be required before service is rendered. To locate your nearest Riccar

Retailer, please call 1-888-6-RICCAR or visit the Riccar website at

www.riccar.com.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER

WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED,

(INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE). THIS WARRANTY DISCLAIMS LIABILITY FOR

INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

How State Law Applies:

This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state.

The model and serial number of this product may be found on the back side of the unit. You

should note the model and serial number of your unit in the spaces provided below, and

retain this book as a permanent record of your purchase.

Date of purchase ____________________________________________________

Serial number _______________________________________________________

Model number ______________________________________________________

Purchased from:

Store name _______________________________________________________

Address _______________________________________________________

City, State, Zip ______________________________________________________

Telephone _______________________________________________________

Your Riccar vacuum cleaner is a product of high quality materials and superior workmanship.

We urge you to read these operating instructions carefully before you use this vacuum

cleaner, in order to obtain the full performance and satisfaction it can offer you.

For Best Performance

• Keep your SupraLite clean and in good operating condition.

• Change vacuum bags once a month or when the bags are 2/3 full to maximize

cleaning performance.

• Always use genuine vacuum bags and replacement parts. Use of other products may

result in poor cleaning performance, potential vacuum cleaner damage and may void

vacuum warranty. Genuine products are designed for maximum cleaning performance.

• Have your SupraLite checked periodically by your Authorized Riccar Retailer.

• Use only Authorized Riccar Retailers for parts or service.

• Store your SupraLite carefully in a dry area.

• For optimum cleaning performance and safety, follow your owner’s manual instructions.

Owner’s information (keep this for your records)

Andere Handbücher für SUPRALITE RSL1A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Riccar Staubsauger Handbücher

Riccar

Riccar R25D Bedienungsanleitung

Riccar

Riccar R-SERIES R500 R500 Bedienungsanleitung

Riccar

Riccar Vibrance R20SC Bedienungsanleitung

Riccar

Riccar VOLT Bedienungsanleitung

Riccar

Riccar RPB-F Bedienungsanleitung

Riccar

Riccar 1800 Bedienungsanleitung

Riccar

Riccar SupraQuick RSQ1 Bedienungsanleitung

Riccar

Riccar SupraLite R10CV Bedienungsanleitung

Riccar

Riccar OMNICLEAN OC1 Bedienungsanleitung

Riccar

Riccar Butler Bedienungsanleitung

Riccar

Riccar 1700 Bedienungsanleitung

Riccar

Riccar 1800 Bedienungsanleitung

Riccar

Riccar SupraLite R10CV Bedienungsanleitung

Riccar

Riccar 1800 Bedienungsanleitung

Riccar

Riccar Pizzazz Bedienungsanleitung

Riccar

Riccar Sunburst Bedienungsanleitung

Riccar

Riccar SupraLite R10E Bedienungsanleitung

Riccar

Riccar SUPRALITE RSL1 Bedienungsanleitung

Riccar

Riccar SUPRALITE RSL1A Bedienungsanleitung

Riccar

Riccar Brilliance BRLD Bedienungsanleitung

Riccar

Riccar 8900 Bedienungsanleitung

Riccar

Riccar 2000 Series Bedienungsanleitung

Riccar

Riccar R40 Bedienungsanleitung

Riccar

Riccar RC-1700P Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch