Ricoh Kir-P1 Service-Handbuch

Technical Bulletin PAGE: 1/3

Model: Model K-P1 Date: 18-Jan-01 No.: RG058001

Subject: Printer Controller Firmware History Prepared by: K. Misugi

From: Technical Services Dept., GTS Division

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Other ( )

Printer controller firmware history for the Kir-P1 (G058/G056 model).

Part Number Version Production

G0565920F 1.05 December ’00 production

G0565920E 1.04 Does not exist in the field

G0565920D 1.03 Does not exist in the field

G0565920C 1.02 November ’00 production

G0565920B 1.01 1st mass production

Note: The above firmware is being used in USA, Europe, and Asia models.

Please refer to the next page for descriptions of the changes.

Technical Bulletin PAGE: 2/3

Model: Model K-P1 Date: 18-Jan-01 No.: RG058001

Descriptions of the changes

Descriptions Version

1. Firmware modified to improve print quality when image data is printed using

the PCL6 driver.

Note: This occurs only in the following condition.

- When printing image data

- When using the PCL6 driver

2. New feature added in the user mode.

“Curl Prevention” mode is added in the user mode.

(Curl Prevention: User mode/ Maintenance)

Please note that the function of this mode is the same as “Curl Control” in the

printer engine service mode.

It lowers the fusing temperature to prevent paper from curling. Advise

customers to use this mode when paper jams occur during duplex rear side

printing.

Note: When this mode is switched on, “Curl Control” in the service mode is

also switched on.

Firmware modified to correct the following problem.

Symptom:

During PCL printing, if data extends over the bottom edge of the printable area, the

machine freezes, displaying "Processing" and operation will no longer be possible.

Condition:

The printer driver is not being used

Print data exists on the bottom edge of the printable area (at 4.2 mm)

4.2

Printable area

The problem occurs only if

data exists on the bottom

edge (4.2mm) of the printable

area .

4.2

Action:

Update the controller firmware.

1.05

Firmware modified to make corrections in the German wording. 1.02

Technical Bulletin PAGE: 3/3

Model: Model K-P1 Date: 18-Jan-01 No.: RG058001

Firmware Updating Procedure

1. Prepare 2 IC cards with the controller firmware.

2. Turn off the main switch.

3. Remove the IC card slot cover on the rear side of the machine as shown.

4. Insert IC card 1 and turn on the main switch.

“Onboard Sys. 1/2” is displayed.

5. Press “# Enter.”

Note: Make sure that ∗is displayed.

6. Scroll with the [▲] [▼] key and select “Update.”

Press “# Enter” to start downloading.

The “On Line” LED starts blinking and the machine starts to

download the program.

(Notice that the ∗mark disappears as the program is

downloaded.)

7. When updating with card 1 is finished, “Update 1/2 task done”

is displayed.

8. Turn off the main switch and replace the card with IC card 2.

Turn on the main switch, then downloading will automatically

start.

9. When updating with card 2 is finished, “Update done” is

displayed.

Then, remove the card, turn on the main switch and print the

configuration sheet.

Check that controller firmware is successfully updated.

Onboard Sys. 1/2

∗

Update

Updating

∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗

Update 1/2 task done

Updating

∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗

Update done

Technical Bulletin PAGE: 1/1

Model: Model K-P1 Date: 03-Apr-01 No.: RG058002

Subject: Printer Engine Firmware History Prepared by: K. Misugi

From: Technical Services Dept., GTS Division

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Other ( )

This RTB announces the printer engine firmware history for model K-P1 (Kir-P1:

G058/G056).

Part Number Version Production

G0525172H 1.11 February ’01

G0525172G 1.10 (does not exist in the field)

G0525172F 1.09 December ’00

G0525172E 1.08 November ’00

G0525172D 1.07 Beginning of mass production

Note: The above firmware is being used in USA, Europe, and Asia models.

Change Descriptions

Descriptions Version

No changes from previous version (only carryover items for Japanese domestic

version). 1.11

Firmware modified to correct the following:

•The machine was showing SC 546 when the symptom was SC 541.

•Duplex backside (leading edge) registration adjustment was applied only to by-

pass feeding. Firmware modified so that the adjustment is applied to all paper

sources.

1.09

The engine process timing is changed to further ensure that waste toner tank

overflow does not occur when the machine is used under low duty. 1.08

Technical Bulletin PAGE: 1/3

Model: Model K-P1 Date: 09-Apr-01 No.: RG058003

Subject: Dirty Background on Printouts Prepared by: K. Misugi

From: Technical Services Dept., GTS Division

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Other ( )

SYMPTOM

Dirty background may occur at installation, either on the right side or throughout the

printout. The following is an example of dirty background on the right side with A4/LT LEF:

Configuration Page

Host Interface

xxxxx

PCL Menu

xxxxx

System Reference

Paper Input

System

Paper Feed Directon

Technical Bulletin PAGE: 2/3

Model: Model K-P1 Date: 09-Apr-01 No.: RG058003

CAUSE

Dirty background on the right side:

The developer will shift to the left side if the cartridge is tilted as shown below when the

sealing tapes are being removed. This causes toner to be over-supplied on the right side

of the cartridge, which in turn causes the dirty background on the right side of the printout.

1234

Developer accumulates on

left side of the cartridge.

1234

When removing the tape, place the

machine on a level surface.

Dirty background throughout the page:

This may occur when the user turns on the main switch without removing the tape seals or

when the cartridge has been shaken after the seals are removed.

The position of the toner agitator is adjusted at the factory. When the main switch is turned

on, the main motor turns the agitator. Then, when the user actually removes the seals and

resets the cartridge in the machine, the agitator is no longer in the proper position, and this

causes dirty background on the printouts.

If the cartridge is shaken after the tape seals are removed, dirty background may occur as

the developer is not evenly distributed in the development unit.

Technical Bulletin PAGE: 3/3

Model: Model K-P1 Date: 09-Apr-01 No.: RG058003

SOLUTION

This symptom may only occur at installation. If it should occur, please advise customers to

print out 30 to 40 pages. In most cases, the symptom will gradually disappear.

In addition, as a preventative measure, please advise customers to be sure and do the

following:

•Remove the seals before turning on the main switch.

•Place the cartridge on a level surface when removing the seals.

•Once the seals have been removed, do not shake the cartridge.

Note: This only applies to cartridge installation and replacement.

From March 2001 production, the following changes were applied to alert customers to

these points.

•Strips of yellow tape have been added that will stick out of the machine, calling

attention to the user to remove the tape seals inside before turning on the main switch.

•A label and caution sheet have been added cautioning the user not to tilt the cartridge

when removing the seals.

Technical Bulletin PAGE: 1/2

Model: Kir-P1 Date: 20-Apr-01 No.: RG058004

Subject: LD Unit Position Adjustment Prepared by: S. Tomoe

From: Technical Services Dept., GTS Division

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Other ( )

The Service Manual procedure for the LD unit position adjustment has been changed from

the first machine of mass production. The new procedure is as follows:

Technical Bulletin PAGE: 2/2

Model: Kir-P1 Date: 20-Apr-01 No.: RG058004

3.3.5 Laser Diode Unit

Laser Unit (☛3.3.4 Laser Unit)

[A]: Spring

[B]: LD unit holders

[C]: Loosen the screw

[D]: Nut

[E]: LD Unit

NOTE: 1) Do not remove the screws that secure the LD board.

2) Do not touch any variable resistors on the LD board.

When installing the LD Unit:

Tighten the screw [C] until the unpainted portion of the screw [F] is not visible.

After installing the LD unit, check the test pattern for the final adjustment (see the following

procedure).

G058R209.WMF

[A]

[B]

[C]

[D]

[E]

[F]

Technical Bulletin PAGE: 1/2

Reissued: 20-Apr-01

Model: Model K-P1 Date: 12-April-01 No.: RG058001a

RTB Correction

The items in bold italics have been corrected or added.

Subject: Printer Controller Firmware History Prepared by: K. Misugi

From: Technical Services Dept., GTS Division

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Other ( )

This RTB informs the printer controller firmware history of the Kir-P1 (G058/G056 model).

Part Number Version Production

G0565920J 1.08 US market: February ’01 production

Europe/Asia: March ’01 production

G0565920G 1.06 US market: Does not exist in the field.

Europe/Asia: February ’01 production

G0565920F 1.05 December ’00 production

(G0565920E) (1.04) Does not exist in the field

(G0565920D) (1.03) Does not exist in the field

G0565920C 1.02 November ’00 production

G0565920B 1.01 1 st mass production

Note: The above firmware is being used in USA, Europe, and Asia models.

Descriptions of the changes (new ones only; for older ones see earlier RTBS)

Descriptions Version

1. Modified so the machine can be used with Axis print servers.

2. Modified to correct Polish and Portuguese wording errors. 1.08

Firmware modified to correct the following problem.

Symptom:

In rare cases with graphic images, dark band appears or part of image

becomes black on printouts.

1.06

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh GR-C1 Series Service-Handbuch

Ricoh

Ricoh 132 MF Bedienungsanleitung

Ricoh

Ricoh AFICIO AP306 Bedienungsanleitung

Ricoh

Ricoh SP 8400DN Bedienungsanleitung

Ricoh

Ricoh L5160 Installationsanleitung

Ricoh

Ricoh CL7000 - Aficio D Color Laser Printer Bedienungsanleitung

Ricoh

Ricoh AP410 Bedienungsanleitung

Ricoh

Ricoh MPC6000 Montage- und Wartungsanleitung

Ricoh

Ricoh SP C340DN Bedienungsanleitung

Ricoh

Ricoh FT5535 Bedienungsanleitung

Ricoh

Ricoh Ri 100 Bedienungsanleitung

Ricoh

Ricoh G1398501 Bedienungsanleitung

Ricoh

Ricoh SP 213SFw Bedienungsanleitung

Ricoh

Ricoh FW780 Bedienungsanleitung

Ricoh

Ricoh BP20 - Aficio B/W Laser Printer Bedienungsanleitung

Ricoh

Ricoh Pro C900s Originalbetriebsanleitung

Ricoh

Ricoh Aficio SP 1210N Bedienungsanleitung

Ricoh

Ricoh MFSP213SFNW1 Bedienungsanleitung

Ricoh

Ricoh AP2610N Bedienungsanleitung

Ricoh

Ricoh GXe3300N Bedienungsanleitung

Ricoh

Ricoh SP 100 e Bedienungsanleitung

Ricoh

Ricoh Pro TF6251 Bedienungsanleitung

Ricoh

Ricoh SP150 series Bedienungsanleitung

Ricoh

Ricoh MP 501SPF Handbuch

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung