RIDGID RV2400HF Bedienungsanleitung

ASSEMBLY

Assemblage

Montaje

Introduction

This Vac is rated for commercial and

household use. This Wet/Dry Vac is

supplied with a certified HEPA dust filter

and meets the EPA definition of a HEPA

vacuum. It can be used for lead

renovation work under the EPA’s Lead

Refer to the assembly sketch for

positioning of parts.

Remove contents of carton. Check each

item against the Carton Contents List.

Call 1-800-4-RIDGID (1-800-474-3443) from

the US and Canada, 01-800-701-9811 from

Mexico, or E-mail us at inf[email protected]

if any parts are damaged or missing.

Unpacking and Checking Carton Contents

Phillips Screwdriver

Tools Required

MalletHammer

RRP rule. It can be used to pick up

material like sawdust and gravel, as well

as ultra fine material like drywall dust and

cold fireplace ash. These types of

materials are so small they would pass

through traditional filters.

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 5

Unpacking and Checking Carton

Contents (cont.)

Carton Contents List

Key Description Qty

A Wet/Dry Vac Assembly ...................1

B Pre-Filter.........................................1

C Certified HEPA Filter ......................1

D “Tug-A-Long Hose™” .....................1

E Diffuser ...........................................1

F Caster Feet, Front ..........................2

G Caster Feet, Rear...........................2

H Casters ...........................................4

I Accessory Storage Bag..................1

J Screw, Type AB #10 x 1-3/4 ...........4

K 14” Floor Brush...............................1

L Wet Nozzle .....................................1

M Crevice Tool ....................................1

N Utility Nozzle...................................1

O Dusting Brush.................................1

P Turbo “Beater Bar” Nozzle..............1

Q 2.5” to 1.25” Adapter ......................1

R Extension Wands............................2

S Owner’s Manual..............................1

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 6

1. Place the HEP

A filter onto the filter

cage until the HEPA filter is snug

against the power head. Be sure the

filter cage’s threaded stud protrudes

through the HEPA filter opening.

NOTE: Make sure the gasket on the

HEPA filter and the sealing surface on the

power head are not damaged and are

clean and free of debris

2. Position the filter washer with the

rubber side against the HEPA filter and

then place the filter wing nut onto the

threaded stud of the filter cage.

Hand-tighten the filter nut to secure the

HEPA filter to the power head.

3. Slide the pre-filter onto the assembled

HEPA filter.

Filter Installation

WARNING: Do not operate

without filter cage and float, as they

prevent liquid from entering the

impeller and damaging the motor.

Power Head

Filter Cage

HEPA

Filter

Filter Washer

Filter

Wing Nut

Lower

End Cap

Pre-Filter

Lower End

Cap

HEPA

Filter

Filter Band Clamp

Power

Head

Filter Band

Clamp

Setscrew

Pre-Filter

4. Locate the filter band clamp on the

pre-filter, over the lower end cap, as

shown. Tighten with a screwdriver to

secure.

NOTE: Damage to filter will occur if filter

band clamp is tightened around the filter

screen.

Power Head

HEPA

Filter

Filter Band

Clamp

Pre-Filter

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 7

If any parts are missing or damaged

contact Customer Service.

Do not assemble until you have all the

parts.

1. Insert the front and rear caster feet into

the bottom of drum as shown. Light

taps with a mallet or hammer may be

needed to fully seat both caster feet.

2. Install (4) #10 x 1-3/4” screws into

matching holes on both front and rear

caster feet, securing them to the

bottom of the drum. Tighten screws

until just snug. Do not over tighten as

this may tend to deform the caster feet.

3. Insert the caster stem into each of the

caster feet, as shown.

4. Push on the caster until the ball on the

caster stem is inserted all the way into

the socket. You will be able to hear the

ball snap into the socket and the caster

will swivel easily when positioning is

correct.

Drum/Caster Foot Assembly

Rear

Caster

Foot

Drain

Front

Caster

Foot

Drum

Front

Caster

Foot

Drain

#10 x 1-3/4"

Screw (4)

Rear

Caster

Foot

Socket

Caster Stem

Caster Ball

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 8

Accessory

Rod

Receptacles

Accessory

Storage Bag

Rods

Power

Head

Accessory

Storage Rod

Pull

Straight

Installing Accessory Storage Bag

1. Position rods of accessory storage bag

directly over accessory rod receptacles

in dust drum.

2. Slide rods of accessory storage bag

into accessory rod receptacles until

fully seated.

Accessory Storage Bag

Removing Accessory Storage

Bag

1. Pull straight up on rods of accessory

storage bag until bag is loose.

NOTE: Power head will need to be

removed before accessory storage bag

can be removed.

Push/Pull Handle

Cord Wrap

Power

Cord

Accessory Storage

Your accessories may be stored in the

accessory storage bag, or in the two

locations on the rear caster feet.

NOTE: Insert female end of extension

wand into the holder sleeve as shown.

Hose Storage

Areas

Accessory

Storage Bag

Female End

of Extension

Wand

Cord Wrap

When vacuuming is complete, unplug the

cord and wrap it around the power

assembly as shown. The cord should wrap

under the pull handle (above the inlet) and

around and under the cord wrap of the

motor cover.

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 9

Wet/Dry Vac Assembly

1. Position the power head assembly on

the drum assembly as shown

(assembled earlier).

NOTE: Make sure the gasket on the

power head and the sealing surface on

the drum are not damaged and are clean

and free of debris

2. Hook the latches over the tab on the

power head assembly. Press the

latches down until they snap closed

against the sides of the drum.

Drum

Latch

Drum

Latch

Power Head

Assembly

Insert Hose

Insert the push button end of the “Tug-A-

Long” hose into the inlet of the Vac. The

hose should snap into place. To remove

the hose from the Vac, press the release

button in the hose assembly and pull the

hose out of the Vac inlet, as shown.

Press

and

Pull

Release

Button

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 10

Introducción

Esta aspiradora para mojado/seco tiene capacidad

para uso comercial y doméstico. Esta aspiradora

para mojado/seco se suministra con un filtro para

polvo HEPA certificado y cumple con la definición

de la EPA de aspiradora HEPA. Se puede utilizar

para realizar trabajo de renovación conforme a la

regla de RRP relacionada con el plomo de la EPA.

Se puede emplear para recoger materiales como

aserrín y grava, así como material ultrafino, tal

como polvo de panel de yeso y ceniza de chimenea

fría. Estos tipos de materiales son tan pequeños

que pasarían a través de los filtros tradicionales.

Consulte el dibujo de ensamblaje para averiguar el

posicionamiento de las piezas. Saque todo el contenido de la caja de cartón.

Asegúrese de que no falte ningún artículo utilizando

la lista del contenido de la caja. Llame al

1-800-4-RIDGID (1-800-474-3443) desde los

EE.UU. y Canadá, y al 01-800-701-9811 desde

México, o envíenos un correo electrónico a

[email protected] si cualquier pieza está

dañada o falta.

Desempaquetado y comprobación del contenido

de la caja de cartón

Destornillador Phillips

Herramientas necesarias

MazoMartillo

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 23

Desempaquetado y comprobación del contenido

de la caja de cartón (cont.)

Lista del contenido de la caja de cartón

Clave Descripción Cant.

A Ensamblaje de la aspiradora

para mojado/seco ................................1

B Prefiltro ....................................................1

C Filtro HEPA certificado .............................1

D Maguera arrastrable Tug-A-Long™ ...........1

E Difusor .....................................................1

F Pies de ruedecilla delanteros ...................2

G Pies de ruedecilla traseros .......................2

H Ruedecillas ...............................................4

I Bolsa de almacenamiento de accesorios ..1

J Tornillo de tipo AB No. 10 x 1-3/4 ............4

KCepillo para pisos de 14 pulg.................1

L Boquilla para mojado ................................1

M Boquilla rinconera .....................................1

N Boquilla de uso general.............................1

O Cepillo para polvo ....................................1

P Boquilla turbo tipo “barra agitadora” .......1

Q Adaptador de 2.5 a 1.25 pulgadas ...........1

R Tubos extensores......................................2

S Manual del usuario....................................1

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 24

1. Coloque el filtro HEPA sobre la jaula del filtro

hasta que dicho filtro HEPA esté perfectamente

ajustado contra el cabezal del motor.

Asegúrese de que el espárrago roscado

de la jaula del filtro sobresalga a través de

la abertura del filtro HEPA.

NOTA: Asegúrese de que la empaquetadura

ubicada sobre el filtro HEPA y la superficie

sellante del cabezal del motor no estén dañadas

y estén limpias y libres de residuos.

2. Posicione la arandela del filtro con el lado de

goma contra el filtro HEPA y luego coloque la

tuerca de mariposa del filtro en el espárrago

roscado de la jaula del filtro. Apriete a mano

la tuerca del filtro para sujetar firmemente el

filtro HEPA al cabezal del motor.

3. Deslice el prefiltro sobre el filtro HEPA

ensamblado.

Instalación del filtro

Power Head

Filter Cage

HEPA

Filter

Filter Washer

Filter

Wing Nut

Lower

End Cap

Pre-Filter

Lower End

Cap

HEPA

Filter

Filter Band Clamp

Power

Head

Filter Band

Clamp

Setscrew

Pre-Filter

4. Ubique la abrazadera de banda del filtro sobre

la tapa de extremo inferior, de la manera que

se muestra en la ilustración. Apriétela con un

destornillador para asegurarla.

NOTA: Se producirán daños en el filtro si la

abrazadera de banda del filtro se aprieta

alrededor del tamiz del filtro.

Power Head

HEPA

Filter

Filter Band

Clamp

Pre-Filter

ADVERTENCIA: No utilice la aspiradora sin

la jaula del filtro y el flotador, ya que estas

piezas evitan que entre líquido en el impulsor y

dañe el motor.

Cabezal del motor

Cabezal

del motor

Tornillo de ajuste

Jaula del filtro

Tapa de

extremo

inferior

Tapa de extremo

inferior

Filtro

HEPA

Filtro

HEPA

Prefiltro

Abrazadera de

banda del filtro

Abrazadera de

banda del filtro

Abrazadera de banda del filtro

Prefiltro

Filtro

HEPA

Arandela del filtro

Tuerca de mariposa

del filtro

SP6775 RV2400HF ESF RIDGID 8/31/10 3:25 PM Page 25

Andere Handbücher für RV2400HF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere RIDGID Staubsauger Handbücher

RIDGID

RIDGID WD4550 Bedienungsanleitung

RIDGID

RIDGID 4000RV Bedienungsanleitung

RIDGID

RIDGID 1400RV0 Bedienungsanleitung

RIDGID

RIDGID HD12000 Bedienungsanleitung

RIDGID

RIDGID WD1250 Bedienungsanleitung

RIDGID

RIDGID VAC11000 Bedienungsanleitung

RIDGID

RIDGID HD16400 Bedienungsanleitung

RIDGID

RIDGID WD03180 Technisches Handbuch

RIDGID

RIDGID RT1200M0 Bedienungsanleitung

RIDGID

RIDGID RT1800M0 Bedienungsanleitung

RIDGID

RIDGID WD1246 Bedienungsanleitung

RIDGID

RIDGID WD20620 Bedienungsanleitung

RIDGID

RIDGID RT1600M0 Bedienungsanleitung

RIDGID

RIDGID WD40701 Bedienungsanleitung

RIDGID

RIDGID HD1200 Bedienungsanleitung

RIDGID

RIDGID 1650RV0 Bedienungsanleitung

RIDGID

RIDGID WD45500 Bedienungsanleitung

RIDGID

RIDGID WD1450 Bedienungsanleitung

RIDGID

RIDGID wd1956 Technisches Handbuch

RIDGID

RIDGID RT1600 Bedienungsanleitung

RIDGID

RIDGID WD19560 Bedienungsanleitung

RIDGID

RIDGID 1620RV0 Bedienungsanleitung

RIDGID

RIDGID AM2560 Bedienungsanleitung

RIDGID

RIDGID 1610RV Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Craftsman

Craftsman CMCVS001D1 Bedienungsanleitung