Rion UV-15 Bedienungsanleitung

3-20-41 Higashimotomachi, Kokubunji, Tokyo 185-8533, Japan

http://www.rion.co.jp/english/

INSTRUCTION MANUAL

Vibration Meter Unit

UV-15

Organization of this manual

This manual describes the features, operation, and other aspects of the Vibration

Meter Unit UV-15. If the unit is used together with other equipment to congure a

measurement system, consult the documentation of all other components as well.

The section starting on page iii contains important information about safety. Be

sure to read and observe these precautions in full.

This manual contains the following sections.

Outline

Gives basic information about the unit and contains a block diagram.

Names of Parts and Functions

Briey identies and explains the front panel controls, rear panel connec-

tors and all other parts of the unit.

Linking

Explains how to congure multiple units as a system.

Power Supply Connection

Explains how to make connections for powering the unit.

Accelerometer Selection and Connection

Explains the types of accelerometers that can be used, how to connect them,

and how to set them up for measurement.

Output Connections

Explains how to use the output connectors on the rear panel.

Operation Modes

Explains the operation modes necessary for measurement, including input

mode, measurement mode, and calibration mode (Output CAL).

Performance Characteristics

Contains charts that show the characteristics of the high-pass lter and low-

pass lter as well as velocity (VEL) and displacement (DISP) frequency

response characteristics.

Specications

Lists the technical specications of the unit.

Reference Material

Provides an explanation of output signal delay. Maintenance parts are also

listed in this section.

* Company names and product names mentioned in this manual are

usually trademarks or registered trademarks of their respective owners.

iii

FOR SAFETY

In this manual, important safety instructions are specially marked as shown

below. To prevent the risk of death or injury to persons and severe damage

to the unit or peripheral equipment, make sure that all instructions are fully

understood and observed.

Caution

WARNING

Important

Disregarding instructions

printed here incurs the risk of

death or severe injury to per-

sons.

Disregarding instructions

printed here incurs the risk of

injury to persons and/or dam-

age to peripheral equipment.

Disregarding instructions

printed here incurs the risk of

damage to the product.

Mentioned about the tips to

use this unit properly. (This

messages do not have to do

with safety.)

Note

To conform to the EU requirement of the Directive

on Waste Electrical and Electronic Equipment,

the symbol mark on the right is shown on the

instrument.

The product described in this manual is in conformity with the

following standards;

Electrical equipment for measurement control and laboratory use.

RION Co., Ltd.

3-20-41 Higashimotomachi, Kokubunji, Tokyo 185-8533, Japan

AC adapter

NC-99 series

Core

Core A: ZCAT2749-0430 (TDK)

Core B~H: ZCAT2436-1330 (TDK)

Equivalent product

Core

This product may cause interference if used in residential areas.

Such use must be avoided unless the user takes special measures

to reduce electromagnetic emissions to prevent interference to

the reception of radio and television broadcasts.

Precautions

•Operate the unit only as described in this manual.

• Do not disassemble the unit or attempt internal alterations.

• Observe the following precautions before using the unit:

- Make sure that all connections are properly and safely established.

- Make sure that the unit is operating normally.

• The permissible ambient temperature range for operation of the unit is

‑10°C to +50°C. Relative humidity must be 90% or below.

• Do not use or store the unit in locations which

- may be subject to strong magnetic elds or strong radiation, or

- may be subject to high levels of dust or splashes of water, or

- may be subject to gases or air with high salt or sulphur content, or

are in the vicinity of stored chemicals, or

- may be subject to high temperature, humidity, or to direct sunlight,

- may be subject vibrations or shock.

• Always switch off the power after using the unit.

• When disconnecting cables, always hold the plug or connector and do not

pull the cable.

• Use only the specied AC adapter or other specied power source.

• This is a precision device. Take care not to drop the unit and protect it

from shocks.

• The LCD panel of the unit can easily become scratched. Do not tap the

panel with a pointed object such as a pencil, screwdriver, etc.

• In case of malfunction, do not attempt any repairs. Note the condition of

the unit clearly and contact the supplier.

• When disposing of the unit, follow national and local regulations regard-

ing waste disposal.

Contents

FOR SAFETY............................................................................... iii

Precautions......................................................................................v

Outline............................................................................................1

Names of Parts and Functions.........................................................4

Front panel.................................................................................4

Rear panel..................................................................................6

LCD panel .................................................................................7

Operation panel .........................................................................9

Top panel .................................................................................11

Bottom panel ...........................................................................11

Linking .........................................................................................12

Linking procedure ...................................................................12

Removing the cable from the link connector............................ 17

Linking with Battery Unit BP-17 .............................................18

Linking with Interface Unit UV-22..........................................19

Using a single UV-15 unit ........................................................20

Power Supply Connection..............................................................21

Using an AC adapter................................................................22

Using the Battery Unit BP-17...................................................23

Accelerometer Selection and Connection ......................................25

Accelerometer connection........................................................26

INPUT (PREAMP) connector wiring diagram...................27

Accelerometer mounting..........................................................28

Output Connections.......................................................................30

vii

Operation Modes...........................................................................31

Input setup mode .....................................................................31

TEDS communication mode....................................................34

Setting the ID number .............................................................35

Measurement setup mode.........................................................36

Calibration mode (OUTPUT CAL) ..........................................38

Measurement mode..................................................................39

Measurement range ............................................................41

Frequency range .................................................................41

Measurement upper limit.................................................... 41

Measurement lower limit....................................................42

Check mode.............................................................................45

Using the Interface Unit UV-22 (option) ..................................46

Restoring the factory default settings.......................................48

Performance Characteristics..........................................................49

Specications ................................................................................51

Reference Material ........................................................................58

Delay of output signal..............................................................58

User Filter................................................................................59

Maintenance parts ...................................................................61

viii

Inhaltsverzeichnis

Andere Rion Messgerät Handbücher

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung