RIOTEC ILS6303XBU Bedienungsanleitung

Programming Quick Guide

iLS6303XBU/iLS6303XB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, turn on your PC

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 from 1 to 3). If you are unable to complete this setting within

1 minute, please re-plug USB cable & re-start the scanner, and try

again.

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6303XB

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Off line / out of service

Green LED ON Good read

Remark:

*When the battery power is too low, the Orange LED will flash

and beep once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully

before turning it back on.

*Under power-saving mode, there will not be LED indication

when charging.

Reset Configuration to Defaults

(scan from A1 to A2 for iLS6303XBU or B1 to B3 for iLS6303XB)

iLS6303XBU iLS6303XB

A1 B1



A2 B3

*Note: Please install PL-2303 driver for iLS6303XB

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

transmission

1transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed Ultra Slow-speed

Transmission 3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner will

stop sending auto-connection signal to device

after 2 minutes. During this time, it will not enter

power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

1

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard for

your country or language. As a general rule, the following characters are

not supported by the scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

Portugal

Switzerland Hungary

Power-saving Mode

Power-saving mode OFF

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

Power-saving mode ON (Default):

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically.

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. scan above configuration code for Prefix or Suffix

2. enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. scan above configuration code for Prefix or Suffix

2. enter the “0” “0” (above, right)

3. then end by scanning Code X (below, right)

Numeric barcode for settings

1 7

2 8

3 9

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL Y

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 951 Q 69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ;53 S 6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D =55 U 6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS) 27 ' 3F ?57 W 6F o

09 Tab

(HT) 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 29 ) 41 A59 Y 71 q

0B CTRL K

(VT) 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 2B + 43 C5B [ 73 s

0D Enter

(CR) 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 2D - 45 E5D ] 75 u

0F CTRL O

(SI) 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 2F / 47 G5F _ 77 w

11 CTRL Q

(DC1) 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 31 1 49 I61 a 79 y

13 CTRL S

(DC3) 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 33 3 4B K63 c 7B {

15 CTRL U

(NAK) 34 4 4C L 64 d 7C |

16 CTRL V

(SYN) 35 5 4D M65 e 7D }

17 CTRL W

(ETB) 36 6 4E N 66 f 7E ~

18 CTRL X

(CAN) 37 7 4F O67 g

2

Reading Techniques

The view finder projects an aiming

beam that should be centered over the

bar code, but it can be positioned in

any direction for a good read.

*Hold the scanner over the bar code, pull the trigger, and center the

aiming beam on the bar code.

*The aiming beam is smaller when the scanner is closer to the code

and larger when it is farther from the code.

1D Symbologies On/OFF -1

ENABLE

Codabar DISABLE

ENABLE

Code 39 DISABLE

ENABLE Code 39

Full ASCII DISABLE

ENABLE Interleaved

2 of 5 DISABLE

3

ENABLE

NEC 2 of 5 DISABLE

1D Symbologies On/OFF -2

ENABLE Straight 2 of 5

Industrial DISABLE

ENABLE Straight 2 of 5

IATA DISABLE

ENABLE Matrix

2 of 5 DISABLE

ENABLE

Code 128 DISABLE

ENABLE

GS1-128 DISABLE

ENABLE

UPC-A DISABLE

ENABLE

UPC-E DISABLE

ENABLE

Code 11 DISABLE

ENABLE

Code 93 DISABLE

1D Symbologies On/OFF -3

ENABLE

Telepen DISABLE

ENABLE GS1 DataBar

Omnidirectional DISABLE

ENABLE GS1 DataBar

Limited DISABLE

ENABLE GS1 DataBar

Expanded DISABLE

ENABLE

MSI DISABLE

ENABLE Trioptic

Code DISABLE

ENABLE

EAN-13 DISABLE

ENABLE

EAN-8 DISABLE

ENABLE

Code 32 DISABLE

*If you are going to scan Code 32, Trioptic Code must be off.

4

2D Symbologies On/OFF

ENABLE

Codablock A DISABLE

ENABLE

Codablock F DISABLE

ENABLE

PDF 417 DISABLE

ENABLE Micro

PDF 417 DISABLE

ENABLE

QR Code DISABLE

ENABLE

Data Matrix DISABLE

ENABLE

MaxiCOde DISABLE

ENABLE

Aztec Code DISABLE

ENABLE Chinese Sensible

(Han Xin) Code DISABLE

Quick guide is subject to change without notice. Q_140902_06

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iLS6302ABQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6300BQ Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6300JS Bedienungsanleitung

RIOTEC

RIOTEC OM7228J Bedienungsanleitung

RIOTEC

RIOTEC LS6307L Bedienungsanleitung

RIOTEC

RIOTEC FS5103A Bedienungsanleitung

RIOTEC

RIOTEC OM7222J Bedienungsanleitung

RIOTEC

RIOTEC iDC9500K Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J BQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9502A Bedienungsanleitung

RIOTEC

RIOTEC iDC9600K Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6308KS Bedienungsanleitung

RIOTEC

RIOTEC LS6303X Bedienungsanleitung

RIOTEC

RIOTEC CR6300C Bedienungsanleitung

RIOTEC

RIOTEC OM7220L Bedienungsanleitung

RIOTEC

RIOTEC iLS6302KS Bedienungsanleitung

RIOTEC

RIOTEC FS5107A Bedienungsanleitung

RIOTEC

RIOTEC LS6308J Bedienungsanleitung

RIOTEC

RIOTEC iDC9607LW Bedienungsanleitung

RIOTEC

RIOTEC FS5027L Bedienungsanleitung

RIOTEC

RIOTEC iDC9270D Bedienungsanleitung

RIOTEC

RIOTEC LS6302J Bedienungsanleitung

RIOTEC

RIOTEC DC9277A Bedienungsanleitung

RIOTEC

RIOTEC iCR6307AB Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iLS6303XBU Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken