RIOTEC LS6307L Bedienungsanleitung

Programming Quick Guide

-LS6307L/ LS6327L.

Installation

Make sure that the scanner has the correct cable to plug in the PC as below

described: *Note : Please install PL-2303 driver for USB serial

Auto-sensing setup (For LS6327L Only)

The auto-sensing will active

while scanner position on stand.

When scanner remove from

stand will become trigger mode.

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan from A1 to A3 for USB HID or B1 to B5 for

RS232 or USB Serial. This will reset the scanner to its factory defaults.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Country (For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

Japan

Denmark

Finland

France

Italy

Norway

Turkey F

Turkey Q

Keyboard Country (For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

Belgium

Spain

Germany

Austria

Russia

Sweden

Portugal

1D Symbologies – 1

ENABLE

EAN-8

DISABLE

ENABLE

EAN-13

DISABLE

ENABLE

ISSN

DISABLE

ENABLE

ISBN

DISABLE

ENABLE

Codabar

DISABLE

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE

Matrix

2 of 5

DISABLE

ENABLE

Industrial 25

DISABLE

ENABLE

Code 39

DISABLE

ENABLE

Code 93

DISABLE

1D Symbologies – 3

ENABLE

GS1-Databar

(RSS)

DISABLE

ENABLE

UPC-E

DISABLE

ENABLE

UPC-A

DISABLE

ENABLE

Interleaved

2 of 5

DISABLE

ENABLE

Code 128

DISABLE

ENABLE GS1-128

UCC/EAN-128

DISABLE

ENABLE

CODE 11

DISABLE

ENABLE

MSI

DISABLE

2D Symbologies

ENABLE

Data

Matrix

DISABLE

ENABLE

QR Code

DISABLE

ENABLE

Micro

QR Code

DISABLE

ENABLE

PDF 417

DISABLE

Inter-Keystroke Delay (For USB HID Only)

This parameter specifies the delay between emulated keystrokes.

No Delay

Short Delay

(20ms)

Long Delay

(40ms)



Information in this document is subject to change without notice.

For more information, please visit:

www.riotec.com.tw

R_170608_01

Dieses Handbuch passt für folgende Modelle

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iCR6307ABM Bedienungsanleitung

RIOTEC

RIOTEC DC9250DP Bedienungsanleitung

RIOTEC

RIOTEC iLS6302ABU Bedienungsanleitung

RIOTEC

RIOTEC iLS6308KBU Bedienungsanleitung

RIOTEC

RIOTEC iLS6303XBU Bedienungsanleitung

RIOTEC

RIOTEC LS6302A Bedienungsanleitung

RIOTEC

RIOTEC iDC9607AW Bedienungsanleitung

RIOTEC

RIOTEC iCR6307AB Bedienungsanleitung

RIOTEC

RIOTEC iDC9507A Bedienungsanleitung

RIOTEC

RIOTEC LS6000B series Bedienungsanleitung

RIOTEC

RIOTEC OM7228J Bedienungsanleitung

RIOTEC

RIOTEC iLS6300DBU Bedienungsanleitung

RIOTEC

RIOTEC CR6300C Bedienungsanleitung

RIOTEC

RIOTEC OM7220L Bedienungsanleitung

RIOTEC

RIOTEC iDC9270D Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6303AS Bedienungsanleitung

RIOTEC

RIOTEC iDC92700 Bedienungsanleitung

RIOTEC

RIOTEC iDC9277A Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iCR6307AS Bedienungsanleitung

RIOTEC

RIOTEC iDC9502N Bedienungsanleitung

RIOTEC

RIOTEC iDC9273A Bedienungsanleitung

RIOTEC

RIOTEC iLS6300FBQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6303ABQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6300BQ Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung