RIOTEC ILS6308KBU Bedienungsanleitung

1

Programming Quick Guide

-iLS6308KBU/iLS6308KB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within Bluetooth radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

* Note: Please install PL-2303 driver for iLS6308KB

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Offline / out of service

Green LED ON Good read

Remark:

* When the battery power is too low, the Orange LED will flash and

beep once. Scanner should be charged immediately.

* If scanner shuts down it is recommended to charge it fully before

turning it back on.

* Under power-saving mode, there will not be LED indication when

charging.

Reset Configuration to Defaults

(scan from A1 to A2 for iLS6308KBU or B1 to B2 for iLS6308KB)

iLS6308KBU iLS6308KB



Note: Please install PL-2303 driver for iLS6308KB

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

Transmission

1 transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2 transmission

Slow-speed Ultra Slow-speed

Transmission 3 transmission

Bluetooth Auto-connection

Bluetooth Auto-connection ON:

When out of range, it will keep trying to connect

to device, scanner will not enter power-saving

mode.

Bluetooth Auto-connection OFF:

When you are out of BT signal range, scanner will

stop sending auto-connection signal to device after

2 minutes. During this time, it will not enter

power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

2

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

ietnam

Sweden

Spain

Denmar

Portu

Switzerland (F)

Hun

ary

Latin America

Icelandic

Brazil

Poland

Belgium

Turkey F

Bulgarian Latin Turkey Q

Finland

Japan

Netherlands

Korea

Thai

Russia

Switzerland German

*The different keyboard language option starts from June. 2017.

Power-saving Mode

Power-saving mode OFF

Powe

-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Powe

-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

* The max. of special characters is 5.

* When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

* It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

3

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 9 51 Q 69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ; 53 S 6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D = 55 U 6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS)

27 ' 3F ? 57 W6F o

09 Tab

(HT) HEX HID

Only 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 80 F1 29 ) 41 A 59 Y 71 q

0B CTRL K

(VT) 81 F2 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 82 F3 2B + 43 C 5B [ 73 s

0D Ente

(CR) 83 F4 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 84 F5 2D - 45 E 5D ] 75 u

0F CTRL O

(SI) 85 F6 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 86 F7 2F / 47 G 5F _ 77 w

11 CTRL Q

(DC1) 87 F8 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 88 F9 31 1 49 I 61 a 79 y

13 CTRL S

(DC3) 89 F10 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 8A F11 33 3 4B K 63 c 7B {

15 CTRL U

(NAK) 8B F12 34 4 4C L 64 d 7C |

16 CTRL

(SYN)

35 5 4D M 65 e 7D }

17 CTRL W

(ETB)

36 6 4E N 66 f 7E ~

18 CTRL

(CAN)

37 7 4F O 67 g

1D Symbologies – 1

ENABLE

UPC-A/E DISABLE

ENABLE

JAN/EAN DISABLE

ENABLE

Code 39 DISABLE

ENABLE

Tri-optic DISABLE

ENABLE

CODE 93 DISABLE

ENABLE

CODE 11 DISABLE

1D Symbologies – 2

ENABLE

UPC-A/E DISABLE

ENABLE

JAN/EAN DISABLE

ENABLE

Code 128 DISABLE

ENABLE

Code 39 DISABLE

ENABLE

Tri-optic DISABLE

ENABLE

CODE 93 DISABLE

ENABLE

CODE 11 DISABLE

4

1D Symbologies – 3

ENABLE GS1 DataBar DISABLE

ENABLE

GS1 DataBar

Limited DISABLE

ENABLE

GS1 DataBar

Expanded DISABLE

ENABLE CODABAR DISABLE

ENABLE Telepen DISABLE

2D Symbologies

ENABLE PDF 417 DISABLE

ENABLE

Micro

PDF 417 DISABLE

ENABLE Data Matrix DISABLE

ENABLE Maxi code DISABLE

ENABLE

Micro

QR CODE DISABLE

ENABLE Aztec DISABLE

Quick guide is subject to change without notice. R_200326_01

Dieses Handbuch passt für folgende Modelle

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iLS6300JB Bedienungsanleitung

RIOTEC

RIOTEC FS5107L Bedienungsanleitung

RIOTEC

RIOTEC iDC9500K Bedienungsanleitung

RIOTEC

RIOTEC LS6308J Bedienungsanleitung

RIOTEC

RIOTEC DC9257L Bedienungsanleitung

RIOTEC

RIOTEC iCR6307AB Bedienungsanleitung

RIOTEC

RIOTEC LS6308K Bedienungsanleitung

RIOTEC

RIOTEC iDC9602NW Bedienungsanleitung

RIOTEC

RIOTEC iLS6303XBQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9502K Bedienungsanleitung

RIOTEC

RIOTEC iLS6302NBQ Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iCR6307AS Bedienungsanleitung

RIOTEC

RIOTEC LS6300 Bedienungsanleitung

RIOTEC

RIOTEC LS6307L Bedienungsanleitung

RIOTEC

RIOTEC FS5100D Bedienungsanleitung

RIOTEC

RIOTEC iDC9270D Bedienungsanleitung

RIOTEC

RIOTEC DC9252NP Bedienungsanleitung

RIOTEC

RIOTEC iLS6300VBQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6303ABQ Bedienungsanleitung

RIOTEC

RIOTEC DC9250 Bedienungsanleitung

RIOTEC

RIOTEC iDC9507J Bedienungsanleitung

RIOTEC

RIOTEC LS6302A Bedienungsanleitung

RIOTEC

RIOTEC DC9270D Bedienungsanleitung

RIOTEC

RIOTEC LS6300F Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iLS6308KBU Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken