RIOTEC ICR6300CBQ Bedienungsanleitung

P r o g ra m m in g Q u ic k G u i d e

- i CR6 3 0 0 C B Q / i CR6300CBM

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within Bluetooth radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iCR6300CBM

LED Indicator Information

Orange LED ON

Full charged

Orange LED Flashing

Charging / Low battery

Red LED ON

Offline / out of service

Green LED ON

Good read

Orange LED ON

Good read (Batch mode)

Remark:

*When the battery power is too low, the Orange LED will flash and beep once.

Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before turning it

back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A4 for iCR6300CBQ or B1 to B5 for iCR6300CBM)

iCR6300CBQ

iCR6300CBM

000602

01802

02C0000000$0D$0A

Demo

%D%F%T

01802

Demo

%D%F%T

*Note: Please install PL-2303 driver for iCR6300CBM

There are two operating modes on the scanner

1.Data Transmission mode (Default)

Demo

%M%A%F

It is a necessary to scan “clean memory data" when

switching between these two modes.

Within Bluetooth radio

range

Beyond Bluetooth radio range

Data

read

Transmit data to PC/terminal

directly

Save data into scanner’s memory,

scanner will transmit data to PC/

terminal automatically when back to

Bluetooth radio range.

Enter Data Storage mode

LED

Green/ Orange LED flashes

followed by 3 beeps.

2.Data Storage mode (Batch Mode)

Demo

%M%A%N

It is a necessary to scan “clean memory data" when switching

between these two modes.

Data

read

Save data directly to scanner’s memory, It will transmit the data to PC/

terminal after you scan the Transmit memory data code. To delete

data please scan the Clean memory data code.

Enter Data Transmission mode

LED

Green/Orange LED flashes followed by 3 beeps.

Always Clean memory data before switching to Data Transmission

Mode.

Otherwise Red/ Orange LED will flash with one long beep and will not

switch modes.

Under Data storage Mode

The data can be keep or delete by option after transmit

Demo

%M%D%K

Demo

%M%D%E

Keep the data

(Default)

Delete the data

Demo

%R%E%C

Transmit memory data

Green/Orange LED Flashes followed by 3 beeps

Demo

%E%R%A

Clean memory data

Green/Orange LED flashes followed by 3 beeps

The barcode data which is stored in the memory will be deleted.

Trigger Mode

Demo

%R%T%E

Trigger always

(Trigger available at any time)

Demo

%R%T%D

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

Demo

%B%T%H

Demo

High-speed

Ultra Slow-speed

Transmission

1transmission

Demo

Middle-speed

Ultra Slow-speed

Transmission

(Default)

2transmission

Demo

%B%T%L

Demo

Slow-speed

Ultra Slow-speed

Transmission

3transmission

Bluetooth Auto-connection

Demo

%A%L%E

Bluetooth Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Demo

%A%L%D

Bluetooth Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode. Once you are

back within range, press trigger to connect to the

device. (Default)

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

%+-$.00

%+-$.06

USA

(Original setting)

Italian

%+-$.01

%+-$.07

Norway

France

%+-$.02

%+-$.08

Germany

Vietnam

%+-$.03

%+-$.09

Sweden

Spain

%+-$.04

%+-$.10

Denmark

Portugal

%+-$.05

%+-$.11

Switzerland (F)

Hungary

%+-$.12

%+-$.18

Latin America

Icelandic

%+-$.13

%+-$.19

Brazil

Poland

%+-$.14

%+-$.20

Belgium

Turkey F

%+-$.15

%+-$.21

Bulgarian Latin

Turkey Q

%+-$.16

%+-$.22

Finland

Japan

%+-$.17

%+-$.23

Netherlands

Korea

%+-$.24

%+-$.26

Thai

Russia

%+-$.25

Switzerland German

*The different keyboard language option starts from June. 2017.

Power-saving Mode

Demo

%P%D%T00

Power-saving mode OFF

Demo

%P%D%T03

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Demo

%P%D%T10

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically

How to append a “prefix” or a “suffix” to the

barcode data

Demo

%C%P%S

Demo

%C%S%S

prefix

suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

Demo

www.tec-it.com

Demo

Prefix & Suffix TABLE

HEX

HID

(SPP)

HEX

HID

(SPP)

HEX

CTRL A

(SOH)

CTRL Y

(EM)

SPACE

CTRL B

(STX)

CTRL

Z(SUB)

CTRL C

(ETX)

ESC

(ESC)

CTRL D

(EOT)

CTRL \

(FS)

;

CTRL E

(ENQ)

CTRL ]

(GS)

CTRL F

(ACK)

CTRL ^

(RS)

CTRL G

(BEL)

CTRL _

(US)

Backspace

(BS)

Tab

(HT)

(

CTRL J

(LF)

)

CTRL K

(VT)

CTRL L

(FF)

[

Enter

(CR)

CTRL N

(SO)

]

CTRL O

(SI)

CTRL P

(DLE)

CTRL Q

(DC1)

CTRL R

(DC2)

CTRL S

(DC3)

CTRL T

(DC4)

{

CTRL U

(NAK)

CTRL V

(SYN)

}

CTRL W

(ETB)

CTRL X

(CAN)

1D Symbologies –1

CODABAR

- ENABLE

CODABAR

-DISABLE

Demo

CODE 11

- ENABLE

CODE 11

- DISABLE

Demo

www.tec-it.com

CODE 39

- ENABLE

CODE 39

- DISABLE

Demo

FULL ASCII

- ENABLE

FULL ASCII

- DISABLE

Demo

CODE 93

-ENABLE

CODE 93

-DISABLE

Demo

1D Symbologies –2

I2OF5

- ENABLE

INTERLEAVED

2 OF 5

I2OF5

- DISABLE

Demo

ID2OF5

-ENABLE

INDUSTRIAL

2 OF 5

ID2OF5

- DISABLE

Demo

MSI

- ENABLE

MSI

- DISABLE

Demo

UPC-A

- ENABLE

UPC/EAN

UPC-A

-DISABLE

Demo

UPC-E -ENABLE

UPC-E

-DISABLE

Demo

EAN-13

-ENABLE

EAN-13

-DISABLE

Demo

Quick guide is subject to change without notice.

R_180808_01

Dieses Handbuch passt für folgende Modelle

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iDC9502N Bedienungsanleitung

RIOTEC

RIOTEC DC9257L Bedienungsanleitung

RIOTEC

RIOTEC iDC9607A Bedienungsanleitung

RIOTEC

RIOTEC iDC9608KW Bedienungsanleitung

RIOTEC

RIOTEC DC9250KP Bedienungsanleitung

RIOTEC

RIOTEC iDC9270D Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J/KBU Bedienungsanleitung

RIOTEC

RIOTEC iDC9500K Bedienungsanleitung

RIOTEC

RIOTEC iDC9273A Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J BQ Bedienungsanleitung

RIOTEC

RIOTEC FS5102N Bedienungsanleitung

RIOTEC

RIOTEC iDC9277L Bedienungsanleitung

RIOTEC

RIOTEC OM7320 Bedienungsanleitung

RIOTEC

RIOTEC iLS6300DBQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6307LBM Bedienungsanleitung

RIOTEC

RIOTEC iDC9608K Bedienungsanleitung

RIOTEC

RIOTEC iLS6302ABQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9600K Bedienungsanleitung

RIOTEC

RIOTEC OM7228J Bedienungsanleitung

RIOTEC

RIOTEC iLS6302ABU Bedienungsanleitung

RIOTEC

RIOTEC iDC9272N Bedienungsanleitung

RIOTEC

RIOTEC iDC9607AW Bedienungsanleitung

RIOTEC

RIOTEC LS6307 USB Bedienungsanleitung

RIOTEC

RIOTEC DC9250 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iCR6300CBQ Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken