Riva RC3202HD-6111 Bedienungsanleitung

NC320209-2013-A

Quick Installation Guide

This manual provides instructions for quick installation and basic configuration of your IP device.

1. Part names and positions

Please check names and positions of each part with the following image. *

DI Out

In Com Com

DI Out

In Com Com

Make sure the polarity is correct. Incorrect connection may

cause malfunction or damage the IP device.

Caution

Power Adaptor Connector (DC 12V)

* Model design and appearance are subject to change without any prior notice.

LAN connector

Power Adaptor

connector

microSD/SDHC slot

Reset button

Ferrite Core

Com

Out

Com

# Please install the ferrite core

included in the package.

Terminal connector for

Digital Input / Output

NC320209-2013-A

Caution

2. Install IP device

When assembling the main body of the camera and its dome cover, make

sure they fit each other into place.

To prevent products from damaging, place the camera on stable and non-

vibrating surfaces If the stability is in doubt, consult with safety personnel

for reinforcements, and then proceed with the installation.

1) Place the installation template

(outline shown on the next page)

included in the package on the

desired installation surface.

2) Drill holes in correct positions

based on the template paper, and

insert anchor blocks into the holes.

3) Make sure the necessary cables

including a LAN cable and a power

cable are properly connected to the

camera either thru the ceiling or

thru the groove around the mounting

plate.

4) Place the camera body and

match the alignment holes with the

corresponding anchor blocks and

hold against the mounting surface.

5) Tighten the anchor blocks with

screws.

6) Adjust the lens position.* Refer

3. Set the lens position for more

detail.

7) Attach the dome cover on main

body and push it toward to the main

body till a “tick” sound is heard.

NC320209-2013-A

3. Set the lens position

1) Remove the dome cover with the opener included in the package.

2) Adjust the lens to the desired position by manually moving its upper lens shell, reinforced

body or horizontal platform in the following directions.

3) Connect to the web page of the device to see its real-time image. Refer to 5. View video on

web page for details about using its web page.

6) Once the lens position is well-adjusted, reverse all the steps in order to reassemble the

device.

** The lens focus is pre-adjusted, best at 3m distance, when the camera is delivered

out of factory. It is recommended not to adjust the lens focus unless it has to be.

More Information

Set Ring

Lens

B. To pan, rotate the lower

body of the camera gimbal.

C. To tilt, tilt the lens by

vertically adjusting the camera.

A. To adjust lens position,

rotate the camera gmbal.

Opener

4) Rotate the set ring counterclockwise will

allow users to adjust the focal length of the

lens.

5) Adjust the focal length of the lens by

rotating the lens. After the setting, tighten

up the set ring by turning it clockwise.

NC320209-2013-A

To learn more about using other features of your devices, refer to the manuals as “RIVA Web

Interface Manual Full HD Series” or “VCAsys Manual Full HD Series”, which is available on

www.rivatech.de homepage.

NC320209-2013-A

4. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of

the device from converting the MAC address’s hexadecimal numbers, which is attached to the

device. Be sure that the device and PC are on a same area network before running the

installation. If the network segment was different between your PC and the device, change your

PC’s settings as below.

IP address : 192.168.xxx.xxx

Subnet mask: 255.255.0.0

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are used,

users may view the live streaming images on a web page using the device’s default IP address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal

Conversion Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2. Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.

3. Web streaming and device configurations are supported through ActiveX program. When

the ActiveX installation pop-up window appears, authorize and install the ActiveX setup.exe.

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two sets of hexadecimal numbers to decimal numbers.

NC320209-2013-A

Custom IP Environment

IPAdminTool and the manual can download from www.rivatech.de homepage.

IPAdminTool is a management tool, which automatically scans all of the network products for

users to perform administrative tasks, which includes network configurations, firmware update,

device reboot, and device organizations.

To modify the device’s default IP address for customized network area;

1. Find the device from the IPAdminTool’s list and highlight the device’s name.

2. Right-click the mouse, and select IP Address; IP Setup window appears.

3. In the IP Setup’s window, information under Local Network information displays the

user/PC’s network area information. Those information need to be incorporated to the IP

Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address,

which are to be the unique numbers for the device. Refer to the image above for the setting

4. Click Setup to complete the modification.

5. Enter the user name and the password, and then select Login.

(The default username and password are: root and pass.)

PC environment Info

Give new unique IP address in

last two sets and mirror other

information in other boxes

NC320209-2013-A

5. View video on web page

Once the device’s proper IP address has been identified, type the URL in a web browser to

access the camera. At first time access, installation window may pop up.

1. When the browser asks to install the AxUMF software, click Install to proceed.

2. When Setup installation pop-up window appears, click Install to proceed with rest of

installations.

Depending on system OS and Internet Explorer version, installation experience may

differ from one another. Figures described above are from Windows 7, Internet

Explorer 9 environment.

6. SETUP page

To set up the device configuration:

1. Click Setup on the upper left of the web page. The login page is displayed as below.

2. Enter the user name and the password, and then select OK.

(The default username and password are: root and pass.)

7. Reboot

Perform the following procedures to reset your device:

1. Press the Reset button, and hold it for 2 seconds while the device is in use.

2. Wait for the system to reboot.

Please do not hold for more than 2 seconds. Otherwise, the camera

may be switched to its Factory Default settings.

Note

Caution

NC320209-2013-A

8. Factory Default

Resetting the device back to the factory default will initialize all parameters including the IP

address back to the factory defaults. To reset back to the factory default:

1. Press the reset button and hold it while the device is in use.

2. Release the button after 10 seconds.

3. Wait for the system to reboot.

The factory default settings can be inferred as follows:

IP address: 192.168.xx.yy

Network mask: 255.255.0.0

Gateway: 192.168.0.1

User ID: root

Password: pass

9. Safe Mode

Your device will get restarted with safe mode when there is an error three times on your

booting system

files. The errors are mainly caused by these two factors: power source unplugged or damage

occurred on

firmware file during the system boot.

You will see the page indicating that your device is in safe mode like below.

Please follow the steps below when your device turns into safe mode.

1. Turn off the device, and turn it on again.

2. Wait until the device completely reboots.

3. Refresh the webpage to check out if the webpage is displayed in normal.

What if your device still remains at safe mode after the above procedure?

It means that some parts of your firmware files on the device are damaged and are not

available anymore.

Then, follow the steps below to recover the firmware file.

1. Click Browse on the screen, and select the appropriate firmware file available.

2. Click START to restore the firmware to the device.

3. Check if the webpage appears normal.

Note

Browse

NC320209-2013-A

There is another method to update firmware, which is using

IPAdminTool.

Please refer to ‘IPAdminTool User’s Manual.pdf’ for the detailed

procedure.

If your device is still at safe mode after trying to update firmware,

please contact your local agency to get further assistance.

Hexadecimal-Decimal Conversion

Table

Refer to the following table when you convert the MAC address of your device to IP

address.

Dec

Note

Andere Handbücher für RC3202HD-6111

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Riva Sicherheitskamera Handbücher

Riva

Riva IPX5502HD-6415-05 Bedienungsanleitung

Riva

Riva RC362HD Bedienungsanleitung

Riva

Riva RC100 Bedienungsanleitung

Riva

Riva RC6602HD-5311 Bedienungsanleitung

Riva

Riva RC6802HD-6217 Bedienungsanleitung

Riva

Riva RC3202HD-6111 Bedienungsanleitung

Riva

Riva RC6702SV-7311 Bedienungsanleitung

Riva

Riva RC362HD-6211IR Bedienungsanleitung

Riva

Riva RC4602SV-7416A-30 Bedienungsanleitung

Riva

Riva RC3302HD-5344 Bedienungsanleitung

Riva

Riva RC6702HD-6211 Bedienungsanleitung

Riva

Riva RC4602HD-6416 Bedienungsanleitung

Riva

Riva RC302HD-5117 Bedienungsanleitung

Riva

Riva RC3302HD-5344 Bedienungsanleitung

Riva

Riva RC3702HD-5314 Bedienungsanleitung

Riva

Riva RC6602HD-5311 Bedienungsanleitung

Riva

Riva RC4602SV01-2017-A Bedienungsanleitung

Riva

Riva RC8102HD-6111T Bedienungsanleitung

Riva

Riva RC6702HD-6311 Bedienungsanleitung

Riva

Riva RC100 Bedienungsanleitung

Riva

Riva RC3402HD-6311 Bedienungsanleitung

Riva

Riva RC4202HD Bedienungsanleitung

Riva

Riva RC5510 Bedienungsanleitung

Riva

Riva RC 4602HD Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung