Robe ColorStrobe IP Bedienungsanleitung

Version 1.

ColorStrobe IP

Table of contents

1. Safety instructions ...................................................................................................................................................... 3

2. Fixture exterior view ................................................................................................................................................... 5

3. Installation .................................................................................................................................................................. 5

3.1 Connection to mains ............................................................................................................................................. 5

3.2 Mounting the fixture ............................................................................................................................................ 6

3.3 DMX 512 connection ............................................................................................................................................ 9

4. Control menu ............................................................................................................................................................ 10

4.1 Fixture Address ................................................................................................................................................... 10

4.2 Fixture information ............................................................................................................................................. 10

4.3 Personality .......................................................................................................................................................... 11

4.4 Manual mode ...................................................................................................................................................... 12

4. 5 Test sequences................................................................................................................................................... 13

4.6 Stand-alone setting ............................................................................................................................................. 13

4.7 Special functions ................................................................................................................................................. 14

5. Strobe and Special effects running ........................................................................................................................... 16

5.1 Strobe ................................................................................................................................................................. 16

5.2 Special effects ..................................................................................................................................................... 16

6. Technical specifications ............................................................................................................................................ 19

7. Cleaning and maintenance ....................................................................................................................................... 22

7.1 Replacing a fuse .................................................................................................................................................. 22

7.2 Disposing of the product .................................................................................................................................... 22

ColorStrobe IP

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE POWERING OR INSTALLING YOUR ColorStrobe IP!

Save it for future reference.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure

safe operation, it is absolutely necessary for the user to follow the safety instructions and warnings written in this

manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual

or any unauthorized modification to the device.

Unauthorized modification will void warranty.

This device is for professional use only. It is not for household use.

1. Safety instructions

DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!

Make sure that the available voltage is not higher than stated on the rear side of the fixture.

This fixture should be operated only from the type of power source indicated on the marking label. If you are not

sure of the type of power supplied, consult your authorized distributor or local power company.

Always disconnect the fixture from AC power before servicing or cleaning internally.

Do not overload supply line as this can result in fire or electric shock.

Make sure the power/data cable is never crimped or damaged by sharp edges. Check the fixture and the

power/data cable from time to time.

Do not install the unit near an open flame.

Refer servicing to qualified service personnel.

Do not connect this fixture to a dimmer pack.

WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely

remove power from unit when not in use or before cleaning or servicing the fixture.

This fixture falls under protection class I. Therefore, this fixture has to be connected to a mains socket outlet

with a protective earthing connection.

Warning! Risk Group 2 LED product according to EN 62471.

LED light emission. Risk of eye injury.

Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.

The light source contains blue LEDs.

Keep combustible material at least 0.3 m away from the fixture.

ColorStrobe IP

If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation of water might damage your device. Leave the device switched off until it

has reached room temperature.

Avoid brute force when installing or operating the fixture.

To guard against epileptic seizure:

Do not operate the fixture near stairways. Provide advance notice that strobe lighting is in use. Avoid extended

periods of continuous flashing, particularly at frequencies of 10 to 20 flashes per second

When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.

Avoid using the unit in locations subject to possible impacts.

Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.

Do not block the front glass cover with any object when the fixture is under operation.

The fixture body must never be covered with cloth or other materials.

The fixture becomes very hot during operation. Allow the fixture to cool approximately 30 minutes prior to

servicing or maintenance.

Operate the fixture only after having familiarized yoursef with its functions. Do not permit operation by persons

not qualified to operate the fixture. Most damages are the result of unprofessional operation!

Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!

Please use the original packaging if the fixture is to be transported.

If this device will be operated in any way different to the one described in this manual, the product may suffer

damages and the warranty becomes void. Furthermore, any other operation may lead to dangers like short-circuit,

burns, electric shock etc.

ColorStrobe IP

2. Fixture exterior view

3. Installation

3.1 Connection to mains

Fixtures must be installed by a qualified electrician in accordance with all national

and local electrical and construction codes and regulations.

This device falls under class one and must be grounded!

The ColorStrobe IP is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC

power source from 100-240V (CE) or 100-277 V (US). The fixture must be connected to a non-dimmable power

source in order to avoid damage to its internal power supply and other electrical components.

Connect the fixture to the mains by means of inbuilt power cord with the plug.

Head with LED array

2. Tilt lock

3. Base

4. Power and DMX connection

5. Attachment point for safety wire

6. Rubber feet

7. Openings for mounting adaptors Omega CL assembled

8. Universal base adaptor for Strobe IP

ColorStrobe IP

3.2 Mounting the fixture

Disconnect the fixture from mains prior to start any installation/assembly works.

The ColorStrobe IP can be arranged in any position/orientation without altering its operation characteristics. The

LED module can be tilted to desired position by means of the tilt lock.

Universal base adaptor installation

Screw the universal base adaptor (8) to the base (3) of the fixture by means of six Allen head bolts M8x25 (12) with

six spring washers .

The Universal base adaptor of the fixture (8) is equipped with two pairs of rubber feet (6) for standing the fixture

on the floor and three pairs of openings (7) for installation of the mounting adaptors Omega CL (9) which allow to

rig the fixture to the truss.

For overhead installation, the fixture must be always secured with a safety wire.

A structure (truss) intended for installation of the fixture (s) must safely hold weight of the fixture(s) placed on it.

The structure has to be certificated to the purpose.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert

before taking into operation for the first time and after changes before taking into operation another time.

IMPORTANT! Overhead installation requires extensive experience including calculating working load limits,

installation material being used, and periodic safety inspection of all installation material and fixtures.

Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible

installation, do not install the fixtures and consult installation with an expert.

ColorStrobe IP

CAUTION!

Use 2 mounting brackets Omega CL and appropriate clamps to rig the fixture on the truss.

Make sure that the device is fixed properly!

Ensure that the structure (truss) to which you are attaching the fixtures is secure

The fixture must never be fixed swinging freely in the room.

For securing the fixture to the truss, install a safety wire which can hold at least 10 times the weight of the fixture.

Use only the safety wire with a snap hook with screw lock gate.

Truss installation

1.Bolt clamp to the Omega adaptor CL (9) with M12 bolts and lock nuts through the hole in the adaptor

Omega CL.

2.Fasten the Omega adaptors (adaptor) CL on the universal base adaptor (8) by means of the quick-lock fasteners

(10) and tighten them fully clockwise.

3. Fasten the safety wire (11) in the attachment point (5) and around the truss.

Possible positions of the adaptors Omega adaptors CL with clamps:

2-bracket installation 2-bracket installation 1-bracket installation

ColorStrobe IP

3.3 Top hat and half top hat installation

Top hat Half top hat

1. Unscrew screws M3x5 (3) to remove the bottom part (2) of the top hat (half top hat).

2. Place the upper part (1) of the top hat (half top hat) on the fixture head and secure it by means of two

screws M5x8 (4) with spring washers to the two threaded holes (A) on the back side of the fixture head.

3. Place the bottom part (2) of the top hat (half top hat) on the bottom part of the fixture head and screw it

back to the upper part (1) of the top hat (half top hat) by means of the screws M3x5 (3).

4. Secure the bottom part of the top hat (half top hat) to the fixture head by means of two screws M5x8 (4)

with spring washers to the two threaded holes (A) on the back side of the fixture head.

3.4 Barn door and Wire guard/anti-glare installation

Barn door Wire guard/anti-glare

1. Unscrew screws M3x5 (3) to remove the bottom part (2) of the barn door (wire guard/anti-glare).

2. Place the upper part (1) of the barn door (wire guard/anti-glare) on the fixture head and secure it by means

of two screws M5x10 (4) with spring washers to the two threaded holes (A) on the back side of the fixture

head.

3. Place the bottom part (2) of the barn door (wire guard/anti-glare) on the bottom part of the fixture head

and screw it back to the upper part (1) of the barn door (wire guard/anti-glare) by means of the screws

M3x5 (3).

4. Secure the bottom part of the barn door (wire guard/anti-glare) to the fixture head by means of two

screws M5x10 (4) with spring washers to the two threaded holes (A) on the back side of the fixture head.

ColorStrobe IP

3.5 DMX 512 connection

The fixture is equipped with 5-pin XLR connectors for DMX input/output.

Only use a shielded twisted-pair cable

designed for RS-485 and 5-pin XLR connectors in order to connect the controller with the fixture or one fixture

with another.

Wiring of the XLR connectors:

XLR socket: XLR plug:

To build a DMX chain

1. Connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain.

2. Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture.

3. Always connect the DMX output with the input of the next fixture until all fixtures are connected.

Do not overload the link. Max. 32 fixtures may be connected on a DMX link.

Caution: Terminate the link by installing a termination plug in the output of the last fixture. The termination plug is

a male 5-pin XLR plug (IP 66 rating) with a 120 Ohm resistor soldered between Signal (–) and Signal (+).

Warning:

Fixture´s XLR connectors are dust and water protected according to IP 67 by mating with related XLR cable

connectors.

They cannot stay disconnected outdoor. DMX output connector (XLR female) at the last fixture in a DMX line

has to be covered with the rubber cap before inserting a terminator. The rubber cap does not supply the

terminator.

The XLR terminator (male) has to be dust and water protected.

If the fixture is to be outdoor without connecting to DMX line, always interconnect its DMX input with DMX output

to keep declared IP rating of XLR connectors.

–

Shield

2 - Signal (-)

3 - Signal (+)

4 – Not connected

–

Not connected

ColorStrobe IP

4. Control menu

The ColorStrobe IP is equipped with a 4-segment LED display which allows you to set the fixture´s behaviour

according to your needs, obtain information on its operation, control all range of effects and program it

in stand-alone mode.

The four control buttons have the following functions:

- ESCAPE button-leaves menu without saving changes.

- ENTER button- enters menu, confirms adjusted values and leaves menu.

- UP and - DOWN buttons - move between menu items on the same level, sets values.

After switching the fixture on, display shows current DMX address.

4.1 Fixture Address

Use this menu to set the DMX address of the fixture.

dM.Ad. --- DMX addressing. Select this submenu to set a DMX start address.

To set a DMX address.

1. Press the ENTER button.

2. Use the UP/DOWN buttons to select desired start address.

3. Press the ENTER button to confirm the choice.

Note: After switching on, the ColorStrobe IP will automatically detect whether DMX 512 data is received or not.

If there is no data received at the DMX input, the display will start to flash the set address.

DM.Pr. --- DMX preset. Select this menu item to set a desired DMX mode.

4.2 Fixture information

Use this menu to read useful information about the fixture status.

To display desired information.

1. Press the ENTER button.

2. Use the UP/DOWN buttons to select the required menu item.

3. Press the ENTER button to confirm the choice.

Po.ti. --- Power On Time. Use the menu item to read the number of operation hours of the fixture.

totL - the function shows the total number of the operation hours since the ColorStrobe IP has been

fabricated.

rESEt - the function shows the number of the operation hours since the counter was last reset.

In order to reset this counter to 0, you have to press and hold the UP and DOWN buttons and at the same

time press the ENTER button.

VErS. ---Software Versions. Select this function to read the software version of the fixture processors.

ICI.b. --- display processor 1

Inhaltsverzeichnis

Andere Robe DJ-Equipment Handbücher

Robe

Robe Robin CycBar 12 Bedienungsanleitung

Robe

Robe ANOLiS Eminere Remote UV 2 Bedienungsanleitung

Robe

Robe Spot 575 XT Bedienungsanleitung

Robe

Robe POINTE 280 Bedienungsanleitung

Robe

Robe DigitalSpot 3000 DT Bedienungsanleitung

Robe

Robe Divine 60 UV Bedienungsanleitung

Robe

Robe Anolis Calumma Remote M MC Bedienungsanleitung

Robe

Robe CitySource 96 WDMX Bedienungsanleitung

Robe

Robe ROBIN ParFect 150 TW Bedienungsanleitung

Robe

Robe redwash 3-192 Bedienungsanleitung

Robe

Robe WeatherShield 575W Series Bedienungsanleitung

Robe

Robe ROBIN T11 MFS Bedienungsanleitung

Robe

Robe ROBIN colorstrobe lite Bedienungsanleitung

Robe

Robe Robin 1200 Bedienungsanleitung

Robe

Robe ROBIN iForte Bedienungsanleitung

Robe

Robe Robin SuperSpike Bedienungsanleitung

Robe

Robe pixelPATT Bedienungsanleitung

Robe

Robe ROBIN UV Strobe Bedienungsanleitung

Robe

Robe Strobe IP Bedienungsanleitung

Robe

Robe ROBIN iParfect 150 RGBA Bedienungsanleitung

Robe

Robe ROBIN SilverScan Wireless DMX Bedienungsanleitung

Robe

Robe StageQube 324 Bedienungsanleitung

Robe

Robe Robin LedBeam 150 Bedienungsanleitung

Robe

Robe REDpower 1-72 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung