Rockwell Automation ArmorPoint 1738-APB Bedienungsanleitung

Publication 1738-IN015C-EN-E - February 2010

Installation Instructions

ArmorPoint PROFIBUS Adapter, Series A

Catalog Number 1738-APB

Inside . . .

For See Page

Important User Information 2

Environment and Enclosure 3

Prevent Electrostatic Discharge 4

About the ArmorPoint PROFIBUS Adapter 4

Install the Module 5

Set the Station Address 7

Troubleshoot 9

Specifications 14

Publication 1738-IN015C-EN-E - February 2010

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature) describes some important differences between solid

state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a

hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be located on or inside the equipment (e.g., drive or motor) to alert people

that dangerous voltage may be present.

BURN HAZARD

Labels may be located on or inside the equipment (e.g., drive or motor) to alert people

that surfaces may be dangerous temperatures.

Publication 1738-IN015C-EN-E - February 2010

Environment and Enclosure

ATTENTION

This equipment is intended for use in overvoltage Category II

applications (as defined in IEC publication 60664-1), at altitudes

up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11. Without

appropriate precautions, there may be potential difficulties

ensuring electromagnetic compatibility in other environments

due to conducted as well as radiated disturbance.

This equipment is supplied as ‘enclosed’ equipment. It should

not require additional system enclosure when used in locations

consistent with the enclosure type ratings stated in the

Specifications section of this publication. Subsequent sections of

this publication may contain additional information regarding

specific enclosure type ratings, beyond what this product

provides, that are required to comply with certain product safety

certifications.

NOTE: See NEMA Standards publication 250 and IEC

publication 60529, as applicable, for explanations of the degrees

of protection provided by different types of enclosure. Also, see

the appropriate sections in this publication, as well as the

Allen-Bradley publication 1770-4.1 (Industrial Automation

Wiring and Grounding Guidelines), for additional installation

requirements pertaining to this equipment.

Publication 1738-IN015C-EN-E - February 2010

Prevent Electrostatic Discharge

About the ArmorPoint PROFIBUS Adapter

The ArmorPoint PROFIBUS adapter ships with the adapter and a

terminating base to be used with the last I/O module on the backplane. The

sealed IP67 housing of the adapter requires no enclosure. Note that it is

possible that environmental requirements other than IP67 will require an

additional appropriate housing. PROFIBUS connectors are sealed M12

(micro) style.

ATTENTION

This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

•When not in use, store the equipment in appropriate

static-safe packaging.

Publication 1738-IN015C-EN-E - February 2010

Refer to the Module Identification illustrations to guide you through the

installation process.

Module Identification

Install the Module

To install the module:

•Mount the adapter and I/O bases

•Wire the adapter

1738-APB

Profibus Out

Profibus In

X10

Adapter

Status

Profibus

Status

PointBus

Status

System

Power

Adapter

Power

PWR

Profibus DP

NetworkConnectors

In and Out, 5-pin,

Micro (M12),

Reverse Keyway

Station

Address

Switches

Auxiliary Power

Connector, 5-pin,

Mini

43790

Publication 1738-IN015C-EN-E - February 2010

Mount the Adapter and I/O Bases

To mount the ArmorPoint adapter on a wall or panel, use the screw holes

provided in the ArmorPoint adapter.

Drilling Dimensions

To install the mounting base:

1. Layout the required points as shown in the Drilling Dimensions

drawing.

2. Drill the necessary holes for #8 (M4) machine or self-tapping screws.

3. Mount the adapter using #8 (M4) screws.

4. Ground the system using the ground lug connection in the I/O bases.

Note that the ground lug connection is also a mounting hole.

5. Mount the terminating base that was shipped with the adapter as the

last base in the backplane instead of the base that was shipped with

the I/O module.

Adapter

102 mm

(4.02 in)

56 mm

(2.2 in)

46.25 mm

(1.8 in) 51.9 mm

(2.0 in)

20.1 mm

(0.8 in) 51.9 mm

(2.0 in) 51.9 mm

(2.0 in)

20.1 mm

(0.8 in)

43769

Publication 1738-IN015C-EN-E - February 2010

Terminating Bases

Set the Station Address

To set the station address, adjust the switches on the front of the module

(refer to the Module Identification illustration). Use a small blade screwdriver

to rotate the switches. Line up the small notch on the switch with the number

setting you wish to use. The two switches are most significant digit (MSD) and

least significant digit (LSD). Valid address are from 01 to 99. The module

reads the switches only when power is applied.

Set Station Address

43787

Mounting Hole

Latching Mechanism

Ground Connection

31433-M

Station Address Set at 63

Publication 1738-IN015C-EN-E - February 2010

GSD File Requirements

Current functionality of PROFIBUS adapters requires GSD files. These files

are easy to install and are available online at:

www.ab.com/networks/gsd/.

Wire the Adapter

Refer to the illustrations for wiring instructions for the adapter.

PROFIBUS In, Male, 5-pin Micro (M12), Reverse Keyway

PROFIBUS Out, Female, 5-pin Micro (M12), Reverse Keyway

The recommended standard cordset for the PROFIBUS auxiliary connector

is 889N-F5AFC- (x), where x equals 6, 12, or 20 feet.

ATTENTION

Make sure all connectors and caps are securely tightened to

properly seal the connections against leaks and maintain IP67

requirements.

Male In

(View into Connector)

Pin 1 - +5VBUS

Pin 2 - A-Line

Pin 3 - GNDBUS

Pin 4 - B-Line

Pin 5 - Shield

43267a

Female Out

43267b

(View into Connector)

Pin 1 - User Power -

Pin 2 - Adapter Power -

Pin 3 - Protective GND

Pin 4 - Adapter Power +

Pin 5 - User Power +

43268

Publication 1738-IN015C-EN-E - February 2010

Troubleshoot

To help you troubleshoot the adapter, refer to the Troubleshoot with the

Indicators illustration and the individual indicator troubleshooting tables.

Troubleshoot with the Indicators

1738-APB

Profibus Out

Profibus In

X10

Adapter

Status

Profibus

Status

PointBus

Status

System

Power

Adapter

Power

PWR

Adapter Status Indicator

Profibus Status Indicator

PointBus Status Indicator

System Power Indicator

Adapter Power Indicator

43790

Publication 1738-IN015C-EN-E - February 2010

Adapter Status Indicator

Refer to the table for a description of the Adapter Status indicator.

Adapter Status Indicator

State Status Description Recommended Action

Off Off or

Process in

Progress

•No power supplied.

•Hardware check is in

progress.

•Initialization is in

progress.

Turn the adapter on or wait until the

hardware check or initialization has

finished.

Green Operating

Normally

The adapter is operating

normally.

None.

Red Hardware

Check

The adapter failed the

hardware check.

Check your hardware and cycle

power to the module. If that does not

fix the fault, contact your Rockwell

Automation representative. There is

the possibility that the module needs

to be replaced.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation E/A-System Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-IA8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ICSTT-RM280N-EN-P Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Handbuch

Rockwell Automation

Rockwell Automation Trusted TMR 120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1771-ID16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Compact 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorBlock Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-IJ2K Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1718-AENTR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-ASCII Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1753-OW8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T8424 Bedienungsanleitung

Rockwell Automation

Rockwell Automation micrologix 1200 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1790D-N4CO Bedienungsanleitung

Rockwell Automation

Rockwell Automation DEVICENET 1771-SDN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Handbuch

Rockwell Automation

Rockwell Automation 1606-XLE80E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Sensia Jiskoot InSpec Remote I/O HUB Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungs- und Sicherheitshinweise

Rockwell Automation

Rockwell Automation Series C Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-SM1 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung