Rockwell Automation Series C Bedienungsanleitung

Publication 1734-IN585C-EN-E - December 2005

Installation Instructions

POINT I/O Protected Sink Output Module

Catalog Numbers 1734-OV2E, 1734-OV4E, and 1734-OV8E

Series C

Inside . . .

For See Page

Important User Information 2

Prevent Electrostatic Discharge 3

Environment and Enclosure 4

North American Hazardous Location Approval 5

About the Module 6

Install the Mounting Base 7

Install the Module 8

Install the Removable Terminal Block (RTB) 11

Remove a Mounting Base 12

Wire the Module 14

Configure the Module 18

Troubleshoot the Module 21

Specifications 23

2POINT I/O Protected Sink Output Module

Publication 1734-IN585C-EN-E - December 2005

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1available from your local Rockwell Automation sales office or online at

http://www.literature.rockwellautomation.com) describes some important differences betweensolid

state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety ofuses for solid state equipment, all persons responsible for applying this

equipment mustsatisfy themselves that each intended application of this equipment is acceptable.

InnoeventwillRockwellAutomation,Inc.be responsibleorliableforindirectorconsequentialdamages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by RockwellAutomation, Inc.with respect touse of information, circuits,

equipment, or software described in this manual.

Reproductionof the contents of thismanual, inwhole or inpart, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifiesinformationaboutpracticesorcircumstancesthatcancauseanexplosionin

a hazardous environment, which may lead to personalinjury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, oreconomic loss. Attentions helpyou identify a

hazard, avoid ahazard, and recognize the consequences.

HOCK HAZARD Labels may be located on or inside the equipment (for example, driveor motor) to

alert people that dangerous voltage may be present.

BURN HAZARD Labels may be located on or inside the equipment (for example, driveor motor) to

alert people that surfaces may be dangerous temperatures.

POINT I/O Protected Sink Output Module 3

Publication 1734-IN585C-EN-E - December 2005

Prevent Electrostatic Discharge

ATTENTIO

This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle this

equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component

boards.

•Do not touch circuit components inside the

equipment.

•Use a static-safe workstation if available.

•Store the equipment in appropriate static-safe

packaging when not in use.

4POINT I/O Protected Sink Output Module

Publication 1734-IN585C-EN-E - December 2005

Environment and Enclosure

ATTENTIO

This equipment is intended for use in a Pollution Degree

2 industrial environment, in overvoltage Category II

applications (as defined in IEC publication 60664-1), at

altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11.

Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated

disturbance.

This equipment is supplied as open-type equipment. It

must be mounted within an enclosure that is suitably

designed for those specific environmental conditions that

will be present and appropriately designed to prevent

personal injury resulting from accessibility to live parts.

The interior of the enclosure must be accessible only by

the use of a tool. Subsequent sections of this publication

may contain additional information regarding specific

enclosure type ratings that are required to comply with

certain product safety certifications.

Besides this publication, see:

•Industrial Automation Wiring and Grounding

Guidelines, Allen-Bradley publication 1770-4.1, for

additional installation requirements.

•NEMA Standards publication 250 and IEC publication

60529, as applicable, for explanations of the degrees

of protection provided by different types of

enclosure.

POINT I/O Protected Sink Output Module 5

Publication 1734-IN585C-EN-E - December 2005

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are suitable

for use in Class I Division 2 Groups A, B, C, D, hazardous

locationsandnonhazardouslocationsonly.Eachproductis

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When

combining products within a system, the most adverse

temperature code (lowest “T” number) may be used to

help determine the overall temperature code of the

system. Combinations of equipment in your system are

subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu’àune utilisation enenvironnementsde Classe I

Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque

d’identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus

défavorable (code de température le plus faible)peut être

utilisé pour déterminer le code de température global du

système. Les combinaisons d’équipements dans le système

sont sujettes à inspection par les autorités locales qualifiées

au moment de l’installation.

EXPLOSION HAZARD -

•Donot disconnectequipmentunless

powerhasbeenremoved orthearea

is known tobe nonhazardous.

•Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded

connectors,orother meansprovided

with this product.

•Substitution of components may

impairsuitabilityforClass I,Division

•If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

RISQUE D’EXPLOSION –

•Couper le courant ou s’assurer que

l’environnement est classé non

dangereux avant de débrancher

l'équipement.

•Couper le courant ou s'assurer que

l’environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les

connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou

autres moyens fournis avec ce

produit.

•La substitution de composants peut

rendrecet équipementinadaptéà une

utilisation en environnement de

Classe 1, Division 2.

•S’assurer que l’environnement est

classé non dangereux avant de

changer les piles.

WARNING AVERTISSEMENT

6POINT I/O Protected Sink Output Module

Publication 1734-IN585C-EN-E - December 2005

About the Module

Use this series C module with the following:

•ControlNet adapters

with RSLogix 5000 software, version 11 or higher

•DeviceNet adapters

•EtherNet/IP adapters

with RSLogix 5000 software, version 11 or higher

•PROFIBUS adapters

Refer to the figure to identify external features of the module.

InterlockingSide

Pieces

DINRailLocking

Screw (orange) RTB Removal Handle

Removable Terminal

Block (RTB)

31830GM

Mounting Base

Mechanical

Keying

(orange)

Module Wiring

Diagram

Module Locking

Mechanism

InsertableI/O

Module

Slide-in Writable Label

POINT I/O Protected Sink Output Module 7

Publication 1734-IN585C-EN-E - December 2005

Install the Mounting Base

To install the mounting base on the DIN rail, proceed as follows.

1. Position the mounting base vertically above the installed units

(adapter, power supply, or existing module).

2. Slide the mounting base down, allowing the interlocking side

pieces to engage the adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail.

The mounting base snaps into place.

ATTENTIO

POINT I/O is grounded through the DIN rail to chassis

ground. Use zinc-plated yellow-chromate steel DIN rail to

assure proper grounding. The use of other DIN rail

material (for example, aluminum and plastic) that can

corrode, oxidize, or are poor conductors, can result in

improper or intermittent grounding.

Secure DIN rail to mounting surface approximately every

200 mm (7.8 in.).

Slide the mounting base to

allow the interlocking side

pieces to engage the

adjacent module or

adapter.

31586

8POINT I/O Protected Sink Output Module

Publication 1734-IN585C-EN-E - December 2005

Install the Module

Install the module before or after base installation. Be sure that you

complete the following.

•Correctly key the mounting base before installing the module

into the mounting base.

•Position the mounting base locking screw horizontal

referenced to the base.

ATTENTIO

When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

Be sure that power is removed or the area is

nonhazardous before proceeding. Repeated electrical

arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may

create electrical resistance that can affect module

operation.

POINT I/O Protected Sink Output Module 9

Publication 1734-IN585C-EN-E - December 2005

To install the module on the DIN rail, proceed as follows.

1. Use a bladed screwdriver to rotate the keyswitch on the

mounting base clockwise until the number required for the

type of module being installed aligns with the notch in the

base.

2. Be sure the DIN rail locking screw is in the horizontal

position.

If you unlock the locking mechanism, you cannot insert the

module.

44009

Notch

(position 3 shown)

Turn the keyswitch to align the number with the notch.

44010

Make sure the DIN rail

locking screw is in the

horizontal position.

10 POINT I/O Protected Sink Output Module

Publication 1734-IN585C-EN-E - December 2005

3. Insert the module straight down into the mounting base.

4. Press to secure.

The module locks into place.

24VDC

Source

Output

Module

Status

Network

Status

1734

OB4E

NODE:

44012

24VDC

Source

Output

Module

Status

Network

Status

1734

OB4E

NODE:

30880

Andere Handbücher für Series C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation E/A-System Handbücher

Rockwell Automation

Rockwell Automation ICSTT-RM280N-EN-P Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 24 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley C Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation FLEX 1794-TB2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation POINTBlock Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ArmorBlock 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorPoint 1738-APB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Series C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-IF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-SM1 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-IA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation DEVICENET 1771-SDN Bedienungsanleitung

Rockwell Automation

Rockwell Automation AB Quality Allen-Bradley SLC 500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1790D-N4CO Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1753-OW8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-IB16D Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley POINT Guard Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1718-AENTR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Handbuch

Rockwell Automation

Rockwell Automation Trusted T8424 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1771-ID16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF8V Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung