Rockwell Automation Series C Bedienungsanleitung

Installation Instructions

POINT I/O 120V AC Input Module

Catalog numbers 1734-IA2, 1734-IA4, Series C

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

North American Hazardous Location Approval 4

European Hazardous Location Approval 5

Before You Begin 6

Install the Mounting Base 8

Install the Module 9

Install the Removable Terminal Block 11

Remove a Mounting Base 13

Wire the Module 14

Communicate with Your Module 17

Interpret Status Indicators 18

Specifications 20

2POINT I/O 120V AC Input Module

Publication 1734-IN010E-EN-E - August 2016

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

POINT I/O 120V AC Input Module 3

Publication 1734-IN010E-EN-E - August 2016

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR Publication 11. Without appropriate precautions, there may be

potential difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if

non-metallic. The interior of the enclosure must be accessible only by the use of

a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, for additional

installation requirements, Allen-Bradley publication 1770-IN041.

• NEMA Standards publication 250 and IEC publication 60529, as applicable,

for explanations of the degrees of protection provided by different types of

enclosure.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O 120V AC Input Module

Publication 1734-IN010E-EN-E - August 2016

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet

équipement en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for

use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When combining

products within a system, the most adverse temperature code

(lowest "T" number) may be used to help determine the

overall temperature code of the system. Combinations of

equipment in your system are subject to investigation by the

local Authority Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux. Chaque produit est livré avec des marquages

sur sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux. Lorsque

plusieurs produits sont combinés dans un système, le code

de température le plus défavorable (code de température le

plus faible) peut être utilisé pour déterminer le code de

température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection

par les autorités locales qualifiées au moment de

l'installation.

EXPLOSION HAZARD

• Do not disconnect equipment unless power

has been removed or the area is known to be

nonhazardous.

• Do not disconnect connections to this

equipment unless power has been removed

or the area is known to be nonhazardous.

Secure any external connections that mate

to this equipment by using screws, sliding

latches, threaded connectors, or other

means provided with this product.

• Substitution of components may impair

suitability for Class I, Division 2.

• If this product contains batteries, they must

only be changed in an area known to be

nonhazardous.

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs.

Fixer tous les connecteurs externes reliés

à cet équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de Classe I,

Division 2.

• S'assurer que l'environnement est classé

non dangereux avant de changer les piles.

POINT I/O 120V AC Input Module 5

Publication 1734-IN010E-EN-E - August 2016

European Hazardous Location Approval

The following applies when the product bears the Ex Marking

This equipment is intended for use in potentially explosive atmospheres as defined by

European Union Directive 94/9/EC.

DEMKO certifies that this equipment has been found to comply with the Essential Health

and Safety Requirements relating to the design and construction of Category 3 equipment

intended for use in Zone 2 potentially explosive atmospheres, given in Annex II to this

Directive.

Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate

number DEMKO 04ATEX0330347X.

WARNING: This equipment shall be mounted in an ATEX certified enclosure

with a minimum ingress protection rating of at least IP54 (as defined in

IEC60529) and used in an environment of not more than Pollution Degree 2

(as defined in IEC 60664-1) when applied in Zone 2 environments. The

enclosure must utilize a tool removable cover or door.

WARNING: This equipment shall be used within its specified ratings

defined by Rockwell Automation.

WARNING: Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 140% of the rated voltage

when applied in Zone 2 environments.

WARNING: Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other means provided

with this product.

WARNING: Do not disconnect equipment unless power has been removed

or the area is known to be nonhazardous.

ATTENTION: This equipment is not resistant to sunlight or other sources of

UV radiation.

6POINT I/O 120V AC Input Module

Publication 1734-IN010E-EN-E - August 2016

Before You Begin

You can use these POINT I/O™ 120V AC Input modules with DeviceNet and

PROFIBUS adapters. If you are using RSLogix 5000 software, version 11 or higher, you

can also use the Series C modules with ControlNet and Ethernet adapters.

Use this diagram to identify the external features of the module.

Note: The wiring base assembly consists of one of the following:

• 1734-TB or 1734-TBS POINT I/O two-piece terminal base, which includes the

1734-RTB Removable Terminal Block

• 1734-TOP or 1734-TOPS POINT I/O single-piece terminal base

POINT I/O 120V AC Input Module

Description Description

1 Module locking mechanism 6 Mounting base – 1734-TB, 1734-TBS

2 Slide-in writable label 7 Interlocking side pieces

3 Insertable I/O module 8 Mechanical keying (orange)

4 Removable Terminal Block (RTB) handle 9 DIN rail locking screw (orange)

5 RTB with screw or spring clamp 10 Module wiring diagram

120VAC

Input

Module

Status

Network

Status

NODE:

45713

POINT I/O 120V AC Input Module 7

Publication 1734-IN010E-EN-E - August 2016

Description Description

1 Module locking mechanism 6 Interlocking side pieces

2 Slide-in writable label 7 Mechanical keying (orange)

3 Insertable I/O module 8 DIN rail locking screw (orange)

4 Handle 9 Module wiring diagram

5 One-piece terminal base with screw or

spring clamp – 1734-TOP, 1734-TOPS

45712

8POINT I/O 120V AC Input Module

Publication 1734-IN010E-EN-E - August 2016

Install the Mounting Base

To install the mounting base on the DIN rail (Allen-Bradley part number 199-DR1;

46277-3; EN50022), proceed as follows:

1. Position the mounting base vertically above the installed units (adapter, power

supply or existing module).

2. Slide the mounting base down allowing the interlocking side pieces to engage the

adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps

into place.

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated yellow-chromate steel DIN rail to assure proper grounding. The

use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately.

31586

POINT I/O 120V AC Input Module 9

Publication 1734-IN010E-EN-E - August 2016

Install the Module

The module can be installed before or after base installation. Make sure that the mounting

base is correctly keyed before installing the module into the mounting base. In addition,

make sure the mounting base locking screw is positioned horizontal referenced to the base.

WARNING: When you insert or remove the module while backplane power is

on, an electrical arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create electrical

resistance that can affect module operation.

Turn the keyswitch to align the

number with the notch.

Notch position 3 is shown here.

Make sure the DIN-rail locking

screw is in the horizontal position.

1734-TB base

45696

10 POINT I/O 120V AC Input Module

Publication 1734-IN010E-EN-E - August 2016

1. Using a bladed screwdriver, rotate the keyswitch on the mounting base clockwise

until the number required for the type of module being installed aligns with the

notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position. You cannot

insert the module if the locking mechanism is unlocked.

3. Insert the module straight down into the mounting base and press to secure. The

module locks into place.

Turn the keyswitch to align the

number with the notch.

Notch position 1 is shown here.

Make sure the DIN-rail locking

screw is in the horizontal position.

1734-TOP base

45697

Andere Handbücher für Series C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation E/A-System Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 1715-AENTR Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1756-DHRIOXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T8424 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1771-ID16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Handbuch

Rockwell Automation

Rockwell Automation Allen-Bradley GuardPLC 1753-IB20XOB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1718-AENTR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-IJ2K Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorBlock Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley C Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorPoint 1738-APB Bedienungsanleitung

Rockwell Automation

Rockwell Automation AB Quality Allen-Bradley SLC 500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ArmorBlock 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley POINT I/O DeviceLogix Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 5094-IA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley IF2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Series C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1753-OW8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-IF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation FLEX 1794-TB2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungs- und Sicherheitshinweise

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung