Rockwell Automation Allen-Bradley 1606-XLP60EQ Bedienungsanleitung

Reference Manual

egaPegaP

1. Intended Use .......................................................3

2. Installation Requirements...................................3

3. AC-Input...............................................................4

4. Input Inrush Current ...........................................5

5. Output .................................................................6

6. Hold-up Time.......................................................7

7. DC-Input...............................................................7

8. Efciency and Power Losses................................8

9. Functional Diagram.............................................9

10. Front Side and User Elements.............................9

11. Terminals and Wiring........................................10

12. Lifetime Expectancy and MTBF.........................10

13. EMC ....................................................................11

14. Environment ......................................................12

15. Protection Features ...........................................13

16. Safety Features ..................................................13

17. Dielectric Strength ............................................14

18. Certications ...................................................15

19. Environmental Compliance ..............................15

20. Physical Dimensions and Weight ......................16

21. Accessory ........................................................... 17

21.1. 1606-XLSBUFFER24 Module........ ..............17

22. Application Notes ............................................. 18

22.1. Peak Current Capability ...........................18

22.2. Back-feeding Loads ..................................18

22.3. Charging Batteries ...............................19

22.4. External Input Protection .........................19

22.5. Parallel Use to Increase Output Power ....19

22.6. Parallel Use for Redundancy ....................20

22.7. Daisy Chaining of Outputs .......................20

22.8. Inductive and Capacitive Loads ................20

22.9. Series Operation .......................................21

22.10. Operation on Two Phases ........................21

22.11. Use Without PE on the Input ...................21

22.12. Use in a Tightly Sealed Enclosure ............22

22.13. Mounting Orientations ............................23

Bulletin 1606 Switched Mode Power Supplies

CatalogNumber:

1606-XLP60EQ

Index

•PEand symbol—PE is the abbreviation for Protective Earth and has the same meaning as the symbol .

•Earth,Ground—This document uses the term “earth” which is the same as the U.S. term “ground”.

• T.b.d.—To be defined, value or description will follow later.

• AC 230VA—A figure displayed with the AC or DC before the value represents a nominal voltage with standard tolerances (usually ±15%)

included. E.g.: DC 12V describes a 12V battery disregarding whether it is full (13.7V) or flat (10V)

• 230Vac—A figure with the unit (Vac) at the end is a momentary figure without any additional tolerances included.

• 50Hz vs. 60Hz—As long as not otherwise stated, AC100V and AC230V parameters are valid at 50Hz and AC120V parameters are valid at 60Hz

mains frequency.

•may—A key word indicating flexibility of choice with no implied preference.

•shall—A key word indicating a mandatory requirement.

•should—A key word indicating flexibility of choice with a strongly preferred implementation.

Terminology and Abbreviations

2Rockwell Automation Publication 1606-RM007A-EN-P - February 2014

Bulletin 1606 Switched Mode Power Supplies

Power Supply

100-240V Wide Range Input

NEC Class 2 Compliant

Adjustable Output Voltage

Efciency up to 89.7%

Low No-load Losses and Excellent Partial-load Efciency

Compact Design, Width only 45mm

Full Power between -10°C and +60°C

Large International Approval Package

3 Year Warranty

Description

Compact size, light weight, easy installation onto the

DIN rail and the utilization of only quality components

are what makes the XLP power supplies so easy to

deploy and use withion seconds.

A rugged electrical and mechanical design as well as a

high immunity against electrical disturbances on the

mains provide reliable output power. This ensures

superior protection for equipment connected to

the public mains network or exposed to a critical

industrial environment.

The XLP family offers output voltages from

5 to 56Vdc and a power rating from 15W to 120W.

Specication Quick Reference

Output voltage DC 24V

Adjustment range 24 - 28V

Output current 2.5A at 24V

2.1A at 28V

Output power 60W

Output ripple < 50mVpp 20Hz to 20MHz

Input voltage AC 100-240V -15% / +10%

Mains frequency 50-60Hz ±6%

AC Input current 0.98 / 0.58A at 120 / 230Vac

Power factor 0.58 / 0.5 at 120 / 230Vac

AC Inrush current typ. 16 / 32A peak value at 120

/ 230Vac 40°C

and cold start

DC Input 88-375Vdc below 110Vdc

derating required

Efciency 87.8 / 89.7% at 120 / 230Vac

Losses 8.3 / 6.7W at 120 / 230Vac

Temperature range -10°C to +70°C operational

Derating 1.5W/°C +60 to +70°C

Hold-up time typ. 24 / 107ms at 120 / 230Vac

Dimensions 45x75x91mm WxHxD

Weight 250g / 0.55lb

Catalog Numbers

Power Supply 1606-XLP60EQ 24-28V Standard unit

Accessories

1606-XLSBUFFER24

Buffer Module

Certication Marks

Ind. Cont. Eq. UL 508

UL 60950-1

Marine

EMC, LVD

Marine RINA

C-Tick

GOST R

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

Rockwell Automation Publication 1606-RM007A-EN-P - February 2014 3

Bulletin 1606 Switched Mode Power Supplies

1. Intended Use

•This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office,

communication, and instrumentation equipment.

•Do not use this power supply in aircraft, trains, nuclear equipment or similar systems where malfunction may cause severe personal injury or

threaten human life.

•This device is designed for use in non-hazardous, ordinary or unclassified locations.

2. Installation Requirements

•This device may only be installed and put into operation by qualified personnel.

•This device does not contain serviceable parts. The tripping of an internal fuse is caused by an internal defect.

•If damage or malfunction should occur during installation or operation, immediately turn power off and send unit to the factory for inspection.

•Mount the unit on a DIN-rail so that the terminals are located on the bottom of the unit. For other mounting orientations, see de-rating

requirements in this document.

•This device is designed for convection cooling and does not require an external fan. Do not obstruct airflow and do not cover ventilation grid

(e.g. cable conduits) by more than 30%!

•Keep the following installation clearances: 40mm on top, 20mm on the bottom, 5mm on the left and right sides are recommended when the

device is loaded permanently with more than 50% of the rated power. Increase this clearance to 15mm in case the adjacent device is a heat

source (e.g. another power supply).

SHOCK HAZARD: Do not use the power supply without proper grounding (Protective Earth). Use the terminal on the input

block for earth connection and not one of the screws on the housing.

- Turn power off before working on the device. Protect against inadvertent re-powering

- Make sure that the wiring is correct by following all local and national codes

- Do not modify or repair the unit

- Do not open the unit as high voltages are present inside

- Use caution to prevent any foreign objects from entering the housing

- Do not use in wet locations or in areas where moisture or condensation can be expected

- Do not touch during power-on, and immediately after power-off. Hot surfaces may cause burns.

WARNING: EXPLOSION HAZARDS!

Substitution of components may impair suitability for this environment. Do not disconnect the unit or operate the voltage adjustment or S/P jumper unless

power has been switched off or the area is known to be non-hazardous.

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

4Rockwell Automation Publication 1606-RM007A-EN-P - February 2014

Bulletin 1606 Switched Mode Power Supplies

3. AC-Input

AC input nom. AC 100-240V -15% / +10%, TN/TT/IT-mains

AC input range

85-264Vac continuous operation, reduce output power linearly

to 50W between 90Vac and 85Vac at ambient

temperatures above +45°C, see Fig. 3-5

264–300Vac < 0.5s

Allowed voltage L or N to earth max. 264Vac or 375Vdc

Input frequency nom. 50–60Hz ±6%

Turn-on voltage typ. 65Vac

Shut-down voltage typ. see Fig. 3-1

AC 100V AC 120V AC 230V

Input current (rms) typ. 1.14A 0.98A 0.58A at 24V, 2.5A see Fig. 3-3

Power factor *) typ. 0.61 0.58 0.50 at 24V, 2.5A see Fig. 3-4

Crest factor **) typ. 3.2 3.3 3.7 at 24V, 2.5A

Start-up delay typ. 170ms ***) 110ms ***) 90ms see Fig. 3-2

Rise time typ. 50ms 50ms 60ms at 24V, 2.5A, 0mF, see Fig. 3-2

120ms 110ms 140ms at 24V, 2.5A, 2.5mF

Turn-on overshoot max. 200mV 200mV 200mV see Fig. 3-2

*) The power factor is the ratio of the true (or real) power to the apparent power in an AC circuit.

**) The crest factor is the mathematical ratio of the peak value to RMS value of the input current waveform.

***) At low temperatures, start-up attempts may occur which extends the start-up delay.

Fig. 3-1 Input voltage range Fig. 3-2 Turn-on behavior, denitions

Rated

input range max.

500ms

OUT

300Vac26465

Start-up

delay Rise

Time

Overshoot

- 5%

Output

Voltage

Input

Voltage

Fig. 3-3 Input current vs. output load at 24V Fig. 3-4 Power factor vs. output load at 24V

2.5A

0.5 1.50

0.4

1.2A

Input Current, typ.

2.0

0.8

1.0

0.6

0.2

a) 100Vac

b) 120Vac

c) 230Vac

Output Current

2.5A

0 0.5 1.0 2.0

0.40

0.45

0.50

0.55

0.60

0.65

Power Factor, typ.

a) 100Vac

b) 120Vac

c) 230Vac b

1.5

Output Current

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

Rockwell Automation Publication 1606-RM007A-EN-P - February 2014 5

Bulletin 1606 Switched Mode Power Supplies

Fig. 3-5 De-rating requirements for

low input voltages

85Vac

60W

Input Voltage

A...<+45°C

B...<+60°C

90Vac

Allowable

Output Power

4. Input Inrush Current

A NTC limits the input inrush current after turn-on of the input voltage. The inrush current is input voltage and

ambient temperature dependent.

The charging current into EMI suppression capacitors is disregarded in the rst microseconds after switch-on.

AC 100V AC 120V AC 230V

Inrush current max. 17Apeak 21Apeak 40Apeak 40°C ambient, cold start

typ. 14Apeak 16Apeak 32Apeak 40°C ambient, cold start

Inrush energy typ. 0.15A2s 0.2A2s 1.0A2s 40°C ambient, cold start

Fig. 4-1 Input inrush current, typical behavior

Fig. 4-2 Input inrush current, zoom into rst peak

Input Voltage

Input Current

Output Voltage

Input Current

Input: 230Vac

Output: 24V, 2.5A

Ambient: 25°C

Input current 2A/DIV

Time basis: 0.5ms / DIV

Input: 230Vac

Output: 24V, 2.5A

Ambient: 25°C

Upper curve: Input current 5A/DIV

Middle curve: Input voltage 100V/DIV

Lower curve: Output voltage 5V/DIV

Time basis: 20ms / DIV

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

6Rockwell Automation Publication 1606-RM007A-EN-P - February 2014

Bulletin 1606 Switched Mode Power Supplies

5. Output

Output voltage nom. 24V

Adjustment range min. 24-28V guaranteed

max. 30V *) at clockwise end position of potentiometer

Factory setting 24.5V ±0.2%, at full load, cold unit

Line regulation max. 10mV 85-264Vac

Load regulation max. 100mV static value, 0A 2.5A

Ripple and noise voltage max. 50mVpp 20Hz to 20MHz, 50Ohm

Output capacitance typ. 1 600μF

Output current nom. 2.5A at 24V, see Fig. 5-1

nom. 2.1A at 28V, see Fig. 5-1

Output power nom. 60W

Short-circuit current min. 3.6A load impedance 400mOhm, see Fig. 5-1

max. 6.2A load impedance 400mOhm, see Fig. 5-1

*) This is the maximum output voltage which can occur at the clockwise end position of the potentiometer due to tolerances. There is no

guarantee this value will be achieved. The typical value is about 28.6V.

Fig. 5-1 Output voltage vs. output current,

typ.

Output Voltage

28V

6A54

Adjustment

Range

Output Current

a) 100Vac

b) 120Vac

c) 230Vac

Peak current capability (up to several milliseconds)

The power supply can deliver a peak current which is higher than the specied short term current. This helps to start

current demanding loads or to safely operate subsequent circuit breakers.

The extra current is supplied by the output capacitors inside the power supply. During this event, the capacitors will be

discharged and causes a voltage dip on the output. Detailed curves can be found in section 22-1.

Peak current voltage dips typ. from 24V to 16V at 5A for 50ms, resistive load

typ. from 24V to 15V at 12.5A for 2ms, resistive load

typ. from 24V to 10.5V at 12.5A for 5ms, resistive load

12 3

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

Rockwell Automation Publication 1606-RM007A-EN-P - February 2014 7

Bulletin 1606 Switched Mode Power Supplies

6. Hold-up Time

AC 100V AC 120V AC 230V

Hold-up Time typ. 36ms 54ms 218ms at 24V, 1.25A, see Fig. 6-1

typ. 15ms 24ms 107ms at 24V, 2.5A, see Fig. 6-1

Note: At no load, the hold-up time can be up to several seconds. The green DC-ok lamp is also on at this time.

Fig. 6-1 Hold-up time vs. input voltage Fig. 6-2 Shut-down behavior, denitions

100

120ms

85 120 155 190 230Vac

Input Voltage

Hold-up Time

a) 24V 1.25A typ.

b) 24V 1.25Amin.

c) 24V 2.5A typ.

d) 24V 2.5A min.

a b c

- 5%

Hold-up Time

Zero Transition

Output

Voltage

Input

Voltage

7. DC Input

The power supply can also be supplied from a DC source. Use a battery or similar DC source. For other sources, contact

RA. Connect the + pole to L and the – pole to N. Connect the PE terminal to an earth wire or to the machine ground.

DC input nom. DC 110-300V -20%/+25%

DC input range min. 88-375Vdc continuous operation, reduce output power according

Fig. 7-2 at voltages below 110Vdc

Allowed Voltage L/N to Earth max. 375Vdc IEC 62103

DC input current typ. 0.62A / 0.22A 110Vdc / 300Vdc, at 24V, 2.5A

Turn-on voltage typ. 80Vdc steady state value

Shut-down voltage typ. 30-70Vdc depending on output load

Fig. 7-1 Wiring for DC Input

Fig. 7-2 Allowable output current below

110Vdc input voltage

Load

Power Supply

Battery

internal

fused

60W

80 90 100 110 130Vdc

Input Voltage Vdc

Output Power

120

(b)(a)

(a) Continuous

(b) Short-term

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

8Rockwell Automation Publication 1606-RM007A-EN-P - February 2014

Bulletin 1606 Switched Mode Power Supplies

8. Efciency and Power Losses

AC 100V AC 120V AC 230V

Efciency typ. 86.5% 87.8% 89.7% at 24V, 2.5A (full load)

Power losses typ. 0.45W 0.5W 0.85W at 0A

typ. 4.0W 3.8W 4.0W at 24V, 1.25A (half load)

typ. 9.4W 8.3W 6.9W at 24V, 2.5A (full load)

Fig. 8-1 Efciency vs. output current at 24V,

typ.

Fig. 8-2 Losses vs. output current at 24V,

typ.

Efciency

92%

2.5A0.5 1.5 2.0

Output Current

1.0

a) 230Vac

b) 120Vac

c) 100Vac

Power Losses

2.5A0.5 1.5 2.0

Output Current

1.0

a) 230Vac

b) 120Vac

c) 100Vac

Fig. 8-3 Efciency vs. input voltage at 24V,

2.5A, typ.

Fig. 8-4 Losses vs. input voltage at 24V, 2.5A,

typ.

Efciency

85 120 155 190 225 260Vac

Input Voltage

91%

Power Losses

12W

85 120 155 190 225 260Vac

Input Voltage

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

Rockwell Automation Publication 1606-RM007A-EN-P - February 2014 9

Bulletin 1606 Switched Mode Power Supplies

9. Functional Diagram

Fig. 9-1 Functional diagram

Input Fuse

Input Filter

Output Over-

Voltage

Protection

Input

Rectier

NTC

Inrush

Limiter

Power

Converter

Output

Voltage

Regulator

Output

Filter

OUT

10. Front Side and User Elements

Fig. 10-1 Front side

AOutput Terminals

Screw terminals,

Dual terminals for the negative and positive pole. Both poles are

equal

+ Positive output

-Negative (return) output

BInput Terminals

Screw terminals

L Phase (Line) input

N Neutral conductor input

PE (Protective Earth) input

CDC-on LED (green)

On, when the voltage on the output terminals is > 17V

DOutput voltage potentiometer

(single turn potentiometer)

Turn to set the output voltage. Factory set: 24.5V

All parameters are specified at 24V, 2.5A, 230Vac input, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

10 Rockwell Automation Publication 1606-RM007A-EN-P - February 2014

Bulletin 1606 Switched Mode Power Supplies

11. Terminals and Wiring

All terminals are easy to access when mounted on the panel. Input and output terminals are separated from each

other (input below, output above) to help in error-free wiring.

Input Output

Type screw terminals screw terminals

Solid wire 0.5-6mm

0.5-6mm

Stranded wire 0.5-4mm

0.5-4mm

American Wire Gauge 20-10 AWG 20-10 AWG

Wire stripping length 7mm / 0.275inch 7mm / 0.275inch

Screwdriver 3.5mm slotted or

Pozidrive No 2

3.5mm slotted or

Pozidrive No 2

Recommended tightening torque 1Nm, 9lb.in 1Nm, 9lb.in

Instructions:

a) Use appropriate copper cables that are designed for an operating temperature of:

60°C for ambient up to 45°C and 75°C for ambient up to 60°C minimum.

b) Follow national installation codes and installation regulations!

c) Ensure that all strands of a stranded wire are fully inserted in the terminal connection!

d) Up to two stranded wires with the same cross section are permitted in one connection point (except PE wire).

e) Do not use the unit without PE connection.

f) Screws of unused terminal compartments should be securely tightened.

g) Ferrules are allowed.

12. Lifetime Expectancy and MTBF

These units are extremely reliable and use only the highest quality materials. The number of critical components such

as electrolytic capacitors has been reduced.

AC 100V AC 120V AC 230V

Lifetime expectancy *) 71 000h 93 000h 128 000h at 24V, 2.5A and 40°C

200 000h *) 264 000h *) 363 000h *) at 24V, 1.25A and 40°C

162 000h *) 233 000h *) 327 000h *) at 24V, 2.5A and 25°C

MTBF **) SN 29500, IEC 61709 1 391 000h 1 667 000h 1 916 000h at 24V, 2.5A and 40°C

2 541 000h 2 964 000h 3 345 000h at 24V, 2.5A and 25°C

MTBF **) MIL HDBK 217F 1 038 000h 1 112 000h 1 060 000h at 24V, 2.5A , 40°C; Ground Benign GB40

1 414 000h 1 517 000h 1 450 000h at 24V, 2.5A , 25°C; Ground Benign GB25

269 000h 295 000h 291 000h at 24V, 2.5A , 40°C; Ground Fixed GF40

355 000h 389 000h 384 000h at 24V, 2.5A , 25°C; Ground Fixed GF25

*) The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime

expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specied in operational hours and is calculated according to the

capacitor’s manufacturer specication. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years

(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.

**) MTBF stands for Mean Time Between Failure, which is calculated according to statistical device failures, and indicates reliability of a

device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent the life of a product.

The MTBF gure is a statistical representation of the likelihood of a device to fail. A MTBF gure of e.g. 1 000 000h means that

statistically one unit will fail every 100 hours if 10 000 units are installed in the eld. However, it can not be determined if the failed unit

has been running for 50 000h or only for 100h.

Inhaltsverzeichnis

Andere Rockwell Automation Stromversorgung Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley SensaGuard 440N-Z21 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation SA500 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS80E Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE96B-2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS960 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLERED Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE960 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480ERZ Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE240EDRZ SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB90E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB90EQ Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE240EL Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Bulletin 1609 Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120EC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480EH Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS180B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120B Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-xlp Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-DNENCAT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB60E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung