Rockwell Automation Allen-Bradley 1606-XLE120E Bedienungsanleitung

Power Supply - 24V, 5 A, 120 W,

Single-phase Input

Catalog Numbers 1606-XLE120E, 1606-XLE120EC,

1606-XLE120EL, 1606-XLE120EH, 1606-XLE120ED

Reference Manual Original Instructions

2Rockwell Automation Publication 1606-RM100A-EN-P - July 2020

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize

themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to

be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use

or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 1606-RM100A-EN-P - July 2020 3

Table of Contents

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Terminology and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Input Inrush Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Hold-up Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DC OK Relay Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Efficiency and Power Losses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Front Side and User Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connection Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Lifetime Expectancy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mean Time Between Failure (MTBF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Safety and Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Dielectric Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Approvals and Fulfilled Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Physical Dimensions

and Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4Rockwell Automation Publication 1606-RM100A-EN-P - July 2020

Notes:

Rockwell Automation Publication 1606-RM100A-EN-P - July 2020 5

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

Product Overview

The 1606-XLE units are high-end power supplies in a medium price range

without compromising quality, reliability, and performance. The XLE Series is

part of the Bulletin 1606 power supply family.

The 1606-XLE120E power supplies come with three connection terminal

options: screw, spring-clamp, or push-in terminals, which are optimized for

automated wiring.

The 1606-XLE120EC is equipped with conformal coated printed circuit boards

that are preferred for the use in harsh environments and the 1606-XLE120ED

features an enhanced DC input voltage range.

These units feature a small size, high efficiency, electronic inrush current

limitation, active power factor correction, and a wide operational temperature

range. The devices have a power reserve of 20% included, which can even be

used continuously at temperatures up to +45 °C (113 °F). Additionally, they can

deliver three times the nominal output current for 12 ms that helps to trip fuses

on faulty output branches.

High immunity to transients and power surges and low electromagnetic

emission, a DC OK signal contact for remote monitoring, and a large

international approval package for various applications.

• AC 100…240V Wide-range Input

• Width only 32 mm(1.26 in.)

• Efficiency up to 94.3%

• Excellent Partial Load Efficiency

• 20% Output Power Reserves

• Easy Fuse Breaking—three times nominal current for 12 ms

• Safe HiccupPLUS Overload Mode

• Active Power Factor Correction (PFC)

• Minimal Inrush Current Surge

• Full Power -25…+60 °C (-13 °F…+140 °F)

• DC OK Relay Contact

6Rockwell Automation Publication 1606-RM100A-EN-P - July 2020

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

Specifications

Catalog Numbers

Terminology and

Abbreviations

Attribute Value Notes

Output voltage 24V DC Nominal

Adjustment range 24…28V Factory setting 24.1V

Output current

6.0…5.1 A Below 45 °C (113 °F) ambient

5.0…4.3 A At 60 °C (140 °F) ambient

3.8…3.2 A —

Derate linearly 45…70 °C (113…158 °F)

Input voltage AC AC 100…240V -15%/+10%

Mains frequency 50…60 Hz ±6%

Input current AC 1.09/0.6 A At 120/230V AC

Powerfactor 0.98/0.91 At 120/230V AC

Input voltage DC DC 110…150V ±20% For 1606-XLE120E, 1606-XLE120EC, 1606-XLE120EL,

1606-XLE120EH

DC 110…300V ±20% For 1606-XLE120ED

Input current DC 1.21/0.43 A At 110/300V DC

ACInrush current 4/4 A At 120/230V AC

Efficiency 93.6/94.3% At 120/230V AC

Losses 8.2/7.3 W At 120/230V AC

Hold-up time 35/35 ms At 120/230V AC

Temperature range -25…+70 °C (-13…+158 °F) —

Size (WxHxD) 32x124x102 mm (1.26x4.88x4.02 in.) WithoutDIN rail

Weight 440 g (0.97 lb) —

Power Supply Connection

1606-XLE120E Screwterminals

1606-XLE120EC Screw terminals and conformal coatedpc-boards

1606-XLE120EL Spring-damp terminals

1606-XLE120EH Push-in terminals

1606-XLE120ED Screw terminals and enhanced DC input

Term Definition

PE and symbol PE is the abbreviation for Protective Earth and has the same meaning as the symbol.

Earth, Ground This document uses the term ‘earth’ which is the same as the U.S. term ‘ground.’

AC 230V A figure that is displayed with the AC or DC before the value represents a nominal voltage

with standard tolerances (usually ±15%) included. For example: DC 12V describes a 12V

battery disregarding whether it is full (13.7V) or flat (10V).

230V AC A figure with the unit (V AC) at the end is a momentary figure without any additional

tolerancesincluded.

50 Hz vs. 60 Hz As long as not otherwise stated, AC 230V parameters are valid at 50 Hz mains frequency.

Rockwell Automation Publication 1606-RM100A-EN-P - July 2020 7

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

AC Input The device is suitable to be supplied from TN, TT, or IT mains networks with

AC voltage. For suitable DC supply voltages, See DC Input on page 8.

Attribute Value Notes

AC input Nom AC 100-240V —

AC input range Min 85-264V AC Continuous operation

Min 264-300V AC Occasionally for maximal 500 ms

Allowed voltage L or N to earth Max 300V AC Continuous, according to IEC 60664-1

Input frequency Nom 50…60 Hz ±6%

Turn-on voltage Typ 80V AC Steady-state value, see Figure 1

Shut-down voltage Typ 74V AC Steady-state value, see Figure 1

External input protection See Installation Instructions on page 6.

AC 100V AC 120V AC 230V

Input current Typ 1.30 A 1.09 A 0.60 A At 24V, 5 A, see Figure 3

Power factor Typ 0.99 0.98 0.91 At 24V, 5 A, see Figure 4

Crest factor Typ 1.7 1.8 2.2 At 24V, 5 A, The crest factor is the mathematical ratio of the peak value to RMS value of the input current

waveform.

Startupdelay Typ 420 ms 380 ms 385 ms See Figure 2

Rise time

Typ 80 ms 80 ms 80 ms At 24V, 5 A constant current load, 0 mF load capacitance, see Figure 2

Typ 100 ms 100 ms 110 ms At 24V, 5 A constant current load, 5 mF load capacitance, see Figure 2

Max 200 mV 200 mV 200 mV See Figure 2

Figure 1 - Input Voltage Range Figure 2 - Turn-on Behavior, Definitions

Figure 3 - Input Current Versus Output Current at 24V Output Voltage Figure 4 - Power Factor Versus Output Current at 24V Output Voltage

8Rockwell Automation Publication 1606-RM100A-EN-P - July 2020

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

DC Input The device is suitable to be supplied from a DC input voltage. Use a battery or a

similar DC source. A supply from the intermediate DC-bus of a frequency

converter is not recommended and can cause a malfunction or damage the

unit.

Connect the +pole to the L, the –pole to N, and the PE terminal to an earth wire

or to the machine ground.

Figure 5 - Wiring for DC Input

Input Inrush Current An active inrush limitation circuit (NTCs, are bypassed by a relay contact)

limits the input inrush current after turn-on of the input voltage.

The charging current into EMI suppression capacitors is disregarded in the

first microseconds after switch-on

Attribute Value Notes

DC input Nom DC 110…150V ±20% For 1606-XLE120E, 1606-XLE120EC, 1606-XLE120EL, 1606-XLE120EH

DC 110…1300V ±20% For 1606-XLE120ED

DC input range Min 88…180V DC Continuous operation for 1606-XLE120E, 1606-XLE120EC, 1606-XLE120EL, 1606-XLE120EH

88…360V DC Continuous operation for 1606-XLE120ED

DC input current Typ 1.21 A At 110V DC, at 24V, 5 A

Typ 0.43 A At 300V DC, at 24V, 5 A

Allowed Voltage (+) or (-) input to Earth Max 360V DC Continuous according to IEC 60664-1

Turn-on voltage Typ 74V DC Steady state value

Shut-down voltage Typ 67V DC Steady state value

Load

Power Supply

Battery

Attribute AC 100V AC 120V AC 230V Notes

Inrush current

Max 8 Apeak 7 Apeak 7 Apeak At 40 °C (104 °F), cold start

Typ 5 Apeak 4 Apeak 4 Apeak At 25 °C (77 °F), cold start

Typ 5 Apeak 5 Apeak 6 Apeak At 40 °C (104 °F), cold start

Inrushenergy Max 0.4 A²s 0.5 A²s 1 A²s At 40 °C (104 °F), cold start

Figure 6 - Typical Turn-on Behavior at Nominal Load, 120V AC Input,

and 25 °C (77 °F) Ambient Figure 7 - Typical Turn-on Behavior at Nominal Load, 230V AC Input,

and 25 °C (77 °F) Ambient

Load

Power Supply

Battery

50ms/DIV

Input

current

2A/DIV

Input

voltage

200V/DIV

Output voltage

Rockwell Automation Publication 1606-RM100A-EN-P - July 2020 9

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

Output The output provides a SELV/PELV rated voltage, which is galvanically isolated

from the input voltage.

The output is designed to supply any kind of loads, including capacitive and

inductive loads. If extreme large capacitors, such as EDLCs (electric double

layer capacitors or ‘Ultra Caps’) with a capacitance > 0.3 F are connected to the

output, the unit can charge the capacitor in an intermittent mode.

The output is electronically protected against overload, no-load, and

short-circuits. If there is a protection event, audible noise can occur.

Attribute Value Notes

Output voltage Nom 24V —

Adjustment range

Min 24…28V Guaranteed value

Max 30.0V This is the maximum output voltage that can occur at the clockwise end position of the

potentiometer due to tolerances. It is not a guaranteed value that can be achieved

Factory settings Typ 24.1V ±0.2%, at full load and cold unit

Line regulation Max 10 mV Between 85V and 300V AC

Load regulation Max 50 mV Between 0 A and 6 A, static value, see Figure 8

Ripple and noise voltage Max 50 mVpp Load > 0.2 A, Bandwidth 20 Hz to 20 MHz, 50 Ohms

Max 200 mVpp Load < 0.2 A, Bandwidth 20 Hz to 20 MHz, 50 Ohms

Output current

Nom 6 A(1) —

Nom 5 A —

Nom 3.8 A —

Nom 5.1 A —

Nom 4.3 A —

Nom 3.2 A —

Derate linearly 45…70 °C (113…158 °F)

Fuse breaking current Typ 15 A Up to 12 ms once every 5 seconds, see Figure 9. The fuse braking current is an enhanced

transient current that helps to trip fuses on faulty output branches. The output voltage stays

above 20V.

Overload behavior Continuouscurrent For output voltage above 13V DC, see Figure 8

Intermittent current(2) For output voltage below 13V DC, see Figure 8

Overload/short-circuit current

Max 7.2 A Continuous current, see Figure 8

Typ 9 A Intermitter current peak value for Typ 1 s.

Load impedance 50 mΩ, see Figure 10 Discharge current of output capacitors is not included

Max 3.5 A Intermitter current average value (R.M.S.) Load impedance 50 mΩ, see Figure 10

Output capacitance

Typ 1800 μF Included inside the powersupply

Max 35V The unit is resistant and does not show malfunctioning when a load feeds back voltage to the

power supply. It does not matter whether the power supply is on or off. The absorbing energy

can be calculated according to the built-in large sized output capacitor.

(1) This current is also available for temperatures up to +70°C (+158 °F) with a duty cycle of 10% and/ or not longer than 1 minute every 10 minutes.

(2) At heavy overloads (when output voltage falls below 13V), the power supply delivers continuous output current for 1s. After this, the output is switched off for approx. 9s before a new start

attempt is automatically performed. This cycle is repeated as long as the overload exists. If the overload has been cleared, the device will operate normally. See Figure 10

Figure 8 - Output Voltage Versus Output Current, Typ Figure 9 - Dynamic Output Current Capability, Typ

Output Voltage

6078

28V

41 2 5 93

Adjustment

Range

Output Current

A: continuous current

B: intermittent current

Output Voltage

(dynamic behavior, < 12ms)

28V

10515202.5 7.5 12.5 17.5 22.5

Adjustment

Range

Output Current

10 Rockwell Automation Publication 1606-RM100A-EN-P - July 2020

Power Supply - 24V, 5 A, 120 W, Single-phase Input Reference Manual

Hold-up Time The hold-up time is the time during which a power supply’s output voltage

remains within specification following the loss of input power. The hold-up

time is output load dependent. At no load, the hold-up time can be up to

several seconds. The green DC OK lamp is also on during this time

DC OK Relay Contact This feature monitors the output voltage on the output terminals of a running

power supply.

Figure 13 - DC OK Relay Contact Behavior

Figure 10 - Short-circuit on Output, HiccupPLUS Mode, Typ

Output

Current

9s 9s

9s 1s 1s

Short-circuit

Normal

Operation Normal

Operation

AC 100V AC 120V AC 230V

Hold-up Time

Typ 70 ms 70 ms 70 ms At 24V, 2.5 A, see Figure 11

Min 55 ms 55 ms 55 ms At 24V, 2.5 A, see Figure 11

Typ 35 ms 35 ms 35 ms At 24V, 5 A, see Figure 11

Min 27 ms 27 ms 27 ms At 24V, 5 A, see Figure 11

Figure 11 - Hold-up Time Versus Input Voltage Figure 12 - Shutdown Behavior, Definitions

90 ms

90 120 155 190 230V AC

Input Voltage

Hold-up Time

c) 24V 5 A typ.

d) 24V 5 A min.

a) 24V 2.5 A typ.

b) 24V 2.5 A min.

- 5%

Hold-up Time

Zero Transition

Output

Voltage

Input

Voltage

Contactcloses As soon as the output voltage reaches Typ 90% of the adjusted output voltage level.

Contactopens As soon as the output voltage dips more than 10% below the adjusted output voltage.

Short dips will be extended to a signal length of 100 ms. Dips shorter than 1 ms will be

ignored.

Switching hysteresis Typically 0.7V

Contact ratings Maximal 60V DC 0.3 A, 30V DC 1 A, 30V AC 0.5 A, resistive load

Minimal permissible load: 1 mA at 5V DC

Isolation voltage See Dielectric Strength on page 17

0.9* V

ADJ

10%

open

OUT =

ADJ

openclosed closed

1...4ms1ms 100ms

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Stromversorgung Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex SCR Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS960EE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB60EH Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS180B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120F Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS960F Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLP60EQ Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE96B-2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS960 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE240EP Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480ERL Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120EC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120EH Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120EL Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120B Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-xlp15 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 104-C60 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSRED40 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE260F Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120F Bedienungsanleitung

Rockwell Automation

Rockwell Automation SA500 Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung