RODE Microphones Procaster Bedienungsanleitung

Thank you for investing in the Procaster™ broadcast

quality dynamic microphone.

The Procaster™ has been designed as a no-compromise

microphone for On-Air broadcast use.

Featuring a tight polar pattern and tailord for voice frequency

response, the Procaster™ is perfect for every application where a

great sounding, rugged microphone with superior ambient noise

rejection is demanded.

Please take the time to visit www.rodemic.com and register your

microphone for a full ten year warranty.

While there, you can view studio tips and techniques, as well as

browse a comprehensive range of accessories for the Procaster™

and other microphones.

SpeciﬁcationsIntroduction

- 2 -- 1 -

(EMC, LVD)

Procaster

Instruction Manual

www.rodemic.com

Acoustic

principle:

Dynamic

Polar pattern: Cardioid

(see graph)

Frequency range: 75Hz ~ 18,000Hz

(see graph)

Output

impedence:

320Ω

Sensitivity: -56dB ± 2 dB re 1V/Pa

(1.6mV @ 94 dB SPL) @ 1 kHz

Output

connection:

3-pin XLR

balanced output between

pin 2(+), pin 3(-)

and pin 1 (ground)

Net weight: 695g (1.53lbs)

Dimensions: Length: 214mm (8.425”)

Width: Ø53mm (2.086”)

Peter Freedman

Microphones

Sydney, Australia

Frequency response:

Polar response:

-2.0

-20.0

-10.0

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Thank you for investing in the Procaster™ broadcast

quality dynamic microphone.

The Procaster™ has been designed as a no-compromise

microphone for On-Air broadcast use.

Featuring a tight polar pattern and tailord for voice frequency

response, the Procaster™ is perfect for every application where a

great sounding, rugged microphone with superior ambient noise

rejection is demanded.

Please take the time to visit www.rodemic.com and register your

microphone for a full ten year warranty.

While there, you can view studio tips and techniques, as well as

browse a comprehensive range of accessories for the Procaster™

and other microphones.

SpeciﬁcationsIntroduction

- 2 -- 1 -

(EMC, LVD)

Procaster

Instruction Manual

www.rodemic.com

Acoustic

principle:

Dynamic

Polar pattern: Cardioid

(see graph)

Frequency range: 75Hz ~ 18,000Hz

(see graph)

Output

impedence:

320Ω

Sensitivity: -56dB ± 2 dB re 1V/Pa

(1.6mV @ 94 dB SPL) @ 1 kHz

Output

connection:

3-pin XLR

balanced output between

pin 2(+), pin 3(-)

and pin 1 (ground)

Net weight: 695g (1.53lbs)

Dimensions: Length: 214mm (8.425”)

Width: Ø53mm (2.086”)

Peter Freedman

Microphones

Sydney, Australia

Frequency response:

Polar response:

-2.0

-20.0

-10.0

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Thank you for investing in the Procaster™ broadcast

quality dynamic microphone.

The Procaster™ has been designed as a no-compromise

microphone for On-Air broadcast use.

Featuring a tight polar pattern and tailord for voice frequency

response, the Procaster™ is perfect for every application where a

great sounding, rugged microphone with superior ambient noise

rejection is demanded.

Please take the time to visit www.rodemic.com and register your

microphone for a full ten year warranty.

While there, you can view studio tips and techniques, as well as

browse a comprehensive range of accessories for the Procaster™

and other microphones.

SpeciﬁcationsIntroduction

- 2 -- 1 -

(EMC, LVD)

Procaster

Instruction Manual

www.rodemic.com

Acoustic

principle:

Dynamic

Polar pattern: Cardioid

(see graph)

Frequency range: 75Hz ~ 18,000Hz

(see graph)

Output

impedence:

320Ω

Sensitivity: -56dB ± 2 dB re 1V/Pa

(1.6mV @ 94 dB SPL) @ 1 kHz

Output

connection:

3-pin XLR

balanced output between

pin 2(+), pin 3(-)

and pin 1 (ground)

Net weight: 695g (1.53lbs)

Dimensions: Length: 214mm (8.425”)

Width: Ø53mm (2.086”)

Peter Freedman

Microphones

Sydney, Australia

Frequency response:

Polar response:

-2.0

-20.0

-10.0

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Using the Procaster

• The Procaster™ is a broadcast-grade end-address

microphone, and for optimum results you should address the

microphone at a distance of no more than 5cm (2”).

• The Procaster™ comes complete with a microphone stand-

mount (RM2) which should be used to attach the microphone

to a good quality stand.

The stand-mount includes a thread adaptor allowing

connection to either 3/8” or 5/8” stand threads.

Alternatively the PSM1 shock mount is optionally available to

isolate the microphone from external vibrations.

• Always use a high quality microphone cable and ensure that it

is wired Pin 1 shield, Pin 2 (+), Pin 3 (-).

• After use the Procaster™ should be wiped with a dry, soft

cloth and placed in its protective zip pouch.

• An absorbent crystal pack is supplied with the Procaster™.

This should stay in the zip pouch at the head of the

microphone when not in use to prevent any build up of

moisture.

When the crystals turn pink, they can be dryed out in an oven

at 100 - 150 degrees celsius for approximately ten minutes.

Once they turn blue they can be reused.

- 4 -

- 3 -

Warranty

All microphones are warranted for one year from date of

purchase. You can extend that to a full ten years if you register

online at www.rodemic.com.

The warranty covers parts and labour that may be required to

repair the microphone during the warranty period. The warranty

excludes defects caused by normal wear and tear, modiﬁcation,

shipping damage, or failure to use the microphone as per the

instruction guide.

If you experience any problems, or have any questions regarding

your microphone, ﬁrst contact the dealer who sold it to

you. If the microphone requires a factory authorised service,

return will be organised by that dealer.

We have an extensive distributor/dealer network, but if you have

difﬁculty getting the advice or assistance you require, do not

hesitate to contact us directly.

Microphones

International

PO Box 6685

Silverwater NSW 2128 Australia

Ph: +61 2 9648 5855

Fax: +61 2 9648 2455

USA

P.O. Box 4189

Santa Barbara, CA 93140-4189

Ph: 805 566 7777

Fax: 805 566 0071

Technical Support

For information and technical support questions contact:

support@rodemic.com

In the Unites States and Puerto Rico, contact

usasupport@rodemic.com or call 805 566 7777

In Australia, contact ozsupport@rodemic.com or call (02) 9648 5855

Anywhere except Australia, the United States and Puerto Rico,

contact support@rodemic.com or call +61 2 9648 5855

• Broadcast sound quality

• High output dynamic capsule

• Balanced, low impedance output

• Internal shock mounting of capsule for

low handling noise

• Internal pop-ﬁlter to reduce plosives

• Robust, all metal construction

• Designed & manufactured in Australia

• Full 10 year guarantee*

Features

Accessories

- 5 -

*Online product registration required.

RM2

stand mount

(included)

PSM1

shock mount

(optional)

ZP1

zip pouch

(included)

PSA1

studio arm

(optional)

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Using the Procaster

• The Procaster™ is a broadcast-grade end-address

microphone, and for optimum results you should address the

microphone at a distance of no more than 5cm (2”).

• The Procaster™ comes complete with a microphone stand-

mount (RM2) which should be used to attach the microphone

to a good quality stand.

The stand-mount includes a thread adaptor allowing

connection to either 3/8” or 5/8” stand threads.

Alternatively the PSM1 shock mount is optionally available to

isolate the microphone from external vibrations.

• Always use a high quality microphone cable and ensure that it

is wired Pin 1 shield, Pin 2 (+), Pin 3 (-).

• After use the Procaster™ should be wiped with a dry, soft

cloth and placed in its protective zip pouch.

• An absorbent crystal pack is supplied with the Procaster™.

This should stay in the zip pouch at the head of the

microphone when not in use to prevent any build up of

moisture.

When the crystals turn pink, they can be dryed out in an oven

at 100 - 150 degrees celsius for approximately ten minutes.

Once they turn blue they can be reused.

- 4 -

- 3 -

Warranty

All microphones are warranted for one year from date of

purchase. You can extend that to a full ten years if you register

online at www.rodemic.com.

The warranty covers parts and labour that may be required to

repair the microphone during the warranty period. The warranty

excludes defects caused by normal wear and tear, modiﬁcation,

shipping damage, or failure to use the microphone as per the

instruction guide.

If you experience any problems, or have any questions regarding

your microphone, ﬁrst contact the dealer who sold it to

you. If the microphone requires a factory authorised service,

return will be organised by that dealer.

We have an extensive distributor/dealer network, but if you have

difﬁculty getting the advice or assistance you require, do not

hesitate to contact us directly.

Microphones

International

PO Box 6685

Silverwater NSW 2128 Australia

Ph: +61 2 9648 5855

Fax: +61 2 9648 2455

USA

P.O. Box 4189

Santa Barbara, CA 93140-4189

Ph: 805 566 7777

Fax: 805 566 0071

Technical Support

For information and technical support questions contact:

support@rodemic.com

In the Unites States and Puerto Rico, contact

usasupport@rodemic.com or call 805 566 7777

In Australia, contact ozsupport@rodemic.com or call (02) 9648 5855

Anywhere except Australia, the United States and Puerto Rico,

contact support@rodemic.com or call +61 2 9648 5855

• Broadcast sound quality

• High output dynamic capsule

• Balanced, low impedance output

• Internal shock mounting of capsule for

low handling noise

• Internal pop-ﬁlter to reduce plosives

• Robust, all metal construction

• Designed & manufactured in Australia

• Full 10 year guarantee*

Features

Accessories

- 5 -

*Online product registration required.

RM2

stand mount

(included)

PSM1

shock mount

(optional)

ZP1

zip pouch

(included)

PSA1

studio arm

(optional)

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Using the Procaster

• The Procaster™ is a broadcast-grade end-address

microphone, and for optimum results you should address the

microphone at a distance of no more than 5cm (2”).

• The Procaster™ comes complete with a microphone stand-

mount (RM2) which should be used to attach the microphone

to a good quality stand.

The stand-mount includes a thread adaptor allowing

connection to either 3/8” or 5/8” stand threads.

Alternatively the PSM1 shock mount is optionally available to

isolate the microphone from external vibrations.

• Always use a high quality microphone cable and ensure that it

is wired Pin 1 shield, Pin 2 (+), Pin 3 (-).

• After use the Procaster™ should be wiped with a dry, soft

cloth and placed in its protective zip pouch.

• An absorbent crystal pack is supplied with the Procaster™.

This should stay in the zip pouch at the head of the

microphone when not in use to prevent any build up of

moisture.

When the crystals turn pink, they can be dryed out in an oven

at 100 - 150 degrees celsius for approximately ten minutes.

Once they turn blue they can be reused.

- 4 -

- 3 -

Warranty

All microphones are warranted for one year from date of

purchase. You can extend that to a full ten years if you register

online at www.rodemic.com.

The warranty covers parts and labour that may be required to

repair the microphone during the warranty period. The warranty

excludes defects caused by normal wear and tear, modiﬁcation,

shipping damage, or failure to use the microphone as per the

instruction guide.

If you experience any problems, or have any questions regarding

your microphone, ﬁrst contact the dealer who sold it to

you. If the microphone requires a factory authorised service,

return will be organised by that dealer.

We have an extensive distributor/dealer network, but if you have

difﬁculty getting the advice or assistance you require, do not

hesitate to contact us directly.

Microphones

International

PO Box 6685

Silverwater NSW 2128 Australia

Ph: +61 2 9648 5855

Fax: +61 2 9648 2455

USA

P.O. Box 4189

Santa Barbara, CA 93140-4189

Ph: 805 566 7777

Fax: 805 566 0071

Technical Support

For information and technical support questions contact:

support@rodemic.com

In the Unites States and Puerto Rico, contact

usasupport@rodemic.com or call 805 566 7777

In Australia, contact ozsupport@rodemic.com or call (02) 9648 5855

Anywhere except Australia, the United States and Puerto Rico,

contact support@rodemic.com or call +61 2 9648 5855

• Broadcast sound quality

• High output dynamic capsule

• Balanced, low impedance output

• Internal shock mounting of capsule for

low handling noise

• Internal pop-ﬁlter to reduce plosives

• Robust, all metal construction

• Designed & manufactured in Australia

• Full 10 year guarantee*

Features

Accessories

- 5 -

*Online product registration required.

RM2

stand mount

(included)

PSM1

shock mount

(optional)

ZP1

zip pouch

(included)

PSA1

studio arm

(optional)

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-pro audio with a smile

Inhaltsverzeichnis

Andere RODE Microphones Mikrofon Handbücher

RODE Microphones

RODE Microphones VideoMic NTG Bedienungsanleitung

RODE Microphones

RODE Microphones NTG-1 Bedienungsanleitung

RODE Microphones

RODE Microphones Procaster Bedienungsanleitung

RODE Microphones

RODE Microphones NT4 Handbuch

RODE Microphones

RODE Microphones NT-USB Bedienungsanleitung

RODE Microphones

RODE Microphones K2 Handbuch

RODE Microphones

RODE Microphones NT5 Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic Bedienungsanleitung

RODE Microphones

RODE Microphones NT2-A Bedienungsanleitung

RODE Microphones

RODE Microphones PODCASTER Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic Me-C Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic Me Bedienungsanleitung

RODE Microphones

RODE Microphones NT 2 Handbuch

RODE Microphones

RODE Microphones NT1A-MP Bedienungsanleitung

RODE Microphones

RODE Microphones Stereo VideoMic X Bedienungsanleitung

RODE Microphones

RODE Microphones NTG-2 Bedienungsanleitung

RODE Microphones

RODE Microphones NT2-A Bedienungsanleitung

RODE Microphones

RODE Microphones STEREO VIDEOMIC PRO Bedienungsanleitung

RODE Microphones

RODE Microphones M1-S Bedienungsanleitung

RODE Microphones

RODE Microphones HS2 Bedienungsanleitung

RODE Microphones

RODE Microphones M5 Bedienungsanleitung

RODE Microphones

RODE Microphones S1 Bedienungsanleitung

RODE Microphones

RODE Microphones NTG-1 Bedienungsanleitung

RODE Microphones

RODE Microphones M3 Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung