Roland LEC-300 Bedienungsanleitung
Before using, be sure
to read this.
The User’s Manual has been partially modied. Be sure to read this document as well as the
User’s Manual before using the machine.
This menu enables you to make a series of required minimum settings by the
interactive method so that you can optimize the output to suit the size and the
type of the media. All the settings made through the [MEDIA SETTING] menu
can also be made individually.
For details, see P. 3, “Setup of Media ([MEDIA SETTING] menu).”
By the addition of the [Media Setting] menu, the main menu system has been
modied.
For details, see P. 14, “Modication of the Main Menu.”
This is one of the menus to be selected when the media take-up system is used.
With [TU2] selected, you can use the media take-up system for the output
involving the pullback movement.
For details, see P. 15,“When Performing Output Involving Pullback Movement
(or When [TU2] Is Selected).”
The [MEDIA SETTING] menu has been added.
MENU
MEDIA SETTING
[TU2] is added to the [SETUP SHEET] menu.
SETUP SHEET
TU2
R2-101012
Contents
Company names and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2010 Roland DG Corporation http://www.rolanddg.com/
Contents
Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing
More Precisely) ..................................................................................................................1
Setup of Media ([MEDIA SETTING] menu) .......................................................................3
Modication of the Main Menu .......................................................................................14
When Performing Output Involving Pullback Movement (or When [TU2] Is Select-
ed)
....................................................................................................................................15
Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing More Precisely)
1
Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing More Precisely)
Perform the initial adjustment (correction for misalignment in bidirectional printing more precisely) of this
machine.This adjustment is necessary in the following cases. If the thickness of the media is over 0.5mm, raise
the head height before performing this adjustment.
User’s Manual, “Adjusting Head Height to Match Media Thickness”
When using this machine for the rst time
When changing the media to use
When the printing is not improved after performing the simplied correction of the bidirec-
tional printing (described in the User’s Manual, “Correcting for Misalignment in Bidirectional
Printing”)
Procedure
Press .
Press several times until the screen shown on
the left appears.
Press and then .
Press .
Press .
A test pattern is printed.
When printing ends, then press .
Press .
Continued on the next page
MENU
ADJUST BI-DIR
ADJUST BI-DIR
DETAIL SETTING
DETAIL SETING
TEST PRINT
DETAIL SETTING
SETTING NO.1
Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing More Precisely)
2
Press to select from H1 to H3 (or from H1
to H6 for LEC-330).
Press to select a correction value from
H1 to H3 (or from H1 to H6 for LEC-330).
Press to nish making the settings for [SETTING
NO.1].
If the Printing-test Results Are Difcult to Interpret
Examine the results from dierent angles in a well-lighted location. Take advantage of reected light to en-
able visual checking.
Press .
In the same manner as performed for [SETTING NO.1], set
the correction values for the other items from [SETTING
NO.2] to [SETTING NO.4].
When correction value settings end, press .
Press in this order to go back to the
original screen.
H4 H5 H6
0 0 0
H1 H2 H3
0 0 0
To decide a Correction Value
Choose the value that produces the least misalignment of 2lines.
H3
H4
H5
H6
H2
H1
NO.1
H3
H4
H2
H1
NO.2
H5
H6
H3
H4
H5
H6
H2
H1
NO.3
H3
H4
H5
H6
H2
H1
NO.4
H3
H2
H1
NO.1
H3
H2
H1
NO.2
H3
H2
H1
NO.3
H3
H2
H1
NO.4
H1
NO.1
DETAIL SETTING
SETTING NO.1
DETAIL SETTING
SETTING NO.2
H4 H5 H6
0 0 0
H1 H2 H3
0 0 0
W 736mm
SETUP SHEET
ROLL
Correction-value scale
Choose the value that produces
the least misalignment.
Current correction value
Only LEC-330
Only LEC-330
Test pattern
LEC-300 / 300A
LEC-330
Setup of Media ( [MEDIA SETTING] menu )
3
Setup of Media ([MEDIA SETTING] menu)
Start the [MEDIA SETTING] menu after performing the initial adjustment.
P.1, "Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing More Precisely)"
Note: If any setting is not needed for each setting item, you can go to the next menu by selecting [NEXT].
1.
Starting the [MEDIA SETTING] menu.
Load media.
Check that no sagging is found on the media. If any sagging exists, the followed correction value settings
do not work eectively.
User’s Manual, “Loading Media”
Press .
When the left gure is displayed, press .
2.
Adjusting the Print Head Height.
Press to select [CHANGE].
Press to enable the setting.
When the left gure is displayed, open the front cover.
Continued on the next page
Only Printing: Perform the procedure
1.
to
5.
, and
9
.
Print & Cut: Perform all the procedure
1.
to
9
.
MENU
MEDIA SETTING
HEAD HGT LOW
[CHANGE] NEXT
HEAD HEIGHT
HIGH LOW
Setup of Media ( [MEDIA SETTING] menu )
4
Move the height-adjustment lever to adjust the head height.
When moving to the [High] direction, the buzzer sounds twice, and to the [Low] direction, the buzzer
sounds once.
Close the front cover.
For the separate setting method and descriptions for this item, see here. User’s Manual, “Adjusting Head
Height to Match Media Thickness”
Normally set to [Low]. However, when the media is over 0.5mm thick, set to [High].
To cancel the setting
Procedure
Press during the setting.
Press to select [YES].
Press .
The screen returns to the screen shown at the left.
By selecting [NO], the screen returns to the screen dis-
played when you pressed .
QUIT SETTING?
[YES] NO
MENU
MEDIA SETTING
High
Low
Height-adjustment lever
Move rmly, until it stops.
High
Low
Height-adjustment lever
Move rmly, until it stops.
LEC-300 / 300A LEC-330
Setup of Media ( [MEDIA SETTING] menu )
5
3.
Perform the position correction of feed direction (Alleviate Horizontal Stripes).
Press to select [SET].
Press to enable the setting.
The test pattern of feed correction is output.
When the left gure is displayed, press .
Use to set the correction value.
Press to enable the setting.
[To conrm again/To adjust again]
Press to select [YES].
Press to enable the setting.
The test pattern of feed correction is output again. Go back to the
procedure
and set again.
[To go to the next after correction is completed]
Press to select [DONE].
Press to enable the setting.
For the separate setting method and descriptions for this item, see here. User’s Manual, “Performing Feed
Correction to Alleviate Horizontal Bands and the Like”
Feed direction means the feed direction of the media. Perform the correction adjusting to the media
in advance because horizontal stripes are more likely to occur during printing when the movement
distance of the media changes subtly depending on the kind or thickness of the media..
CALIBRATION
[SET] NEXT
INPUT
ADJ. VALUES
CALIBRATION
0.10% -0.10%
To decide a Correction Value
Select the value to make the upper/lower rectangular gap and overlap smallest.
REDO ADJ. ?
YES [DONE]
Current correction
value
Value to be set
Gap present Overlap
Smallest gap and overlap
Current correction
value
Setup of Media ( [MEDIA SETTING] menu )
6
4.
Performing the correction for misalignment in bidirectional printing
Press to select [SET].
Press to enable the setting.
The test pattern of bidirectional correction is output.
When the left gure is displayed, press .
Use to set the correction value.
Press to enable the setting.
[To conrm again/adjust again]
Press to select [YES].
Press to enable the setting.
The test pattern of bidirectional correction is output again. Go back
to the procedure
and set again.
[To go to the next after correction is completed]
Press to select [DONE].
Press to enable the setting.
For the separate setting method and descriptions for this item, see here. User’s Manual, “Correcting for
Misalignment in Bidirectional Printing”
This machine prints by the bidirectional mode (in which the heads perform printing during both
their outbound pass and return pass). This printing method is called “Bidirectional Printing.” This
method oers the advantage of being able to shorten output times, but subtle misalignment occurs
during the outbound and return passes. The procedure to correct this and eliminate misalignment
is “Bidirectional Correction.”
ADJUST BI-DIR
[SET] NEXT
INPUT
ADJ. VALUES
ADJUST BI-DIR
0 -6
To decide a Correction Value
Choose the value that produces the least misalignment of 2lines.
REDO ADJ. ?
YES [DONE]
Current correction
value
Value to be set
Correction value scale Current cor-
rection value
The least misalignment.
Setup of Media ( [MEDIA SETTING] menu )
7
5.
Deciding to perform the setting for cutting or not
[Only Printing]
Press to select [NEXT].
Press to enable the setting.
Go to Procedure
9
.
[Print & Cut]
Press to select [SET].
Press to enable the setting.
Go to Procedure
6
.
6.
Setting the blade force
Press to select [SET].
Press to enable the setting.
The test pattern is cut. Circle and rectangle are cut. Peel o the
two shapes.
Continued on the next page
CUT CONFIG
[SET] NEXT
For high-quality cutting, perform a cutting test to check the cutting quality for the media and adjust
the blade force.
When Cutting the Printed Surface
Hardened ink is thick. When cutting a printed surface, rst perform a cutting test on the actual
surface that has been printed.
The end of the cap for the blade holder may scrape or damage the printed surface. If this happens,
increase the amount of blade extension.
User’s Manual, “Adjusting the Cutting-in Amount” and“Adjusting for When Cutting the Printed Surface”
CUT FORCE
[SET] NEXT
Circle
Rectangle
Setup of Media ( [MEDIA SETTING] menu )
8
[Two shapes are peeled off separately]
Press to select [DONE].
Press to enable the setting.
Go to Procedure
7
.
[Two shapes are peeled off together/backing paper is
also cut]
Press to select [YES].
Press to enable the setting.
Go to Procedure
.
Press to adjust the blade force.
If two shapes are peeled o together raise the blade force.
If backing paper is cut too reduce the blade force.
Press to enable the setting.
Cut the test pattern again. Check the result.
[Two shapes are peeled off separately]
Press to select [DONE].
Press to enable the setting.
Go to Procedure
7
.
[Two shapes are peeled off together]
Press to select [YES].
Press to enable the setting.
Cut the test pattern again. Go back to the procedure
and set
again.
For the separate setting method and descriptions for this item, see here. User’s Manual, “Fine-tuning the
Cutting Conditions”
CONTINUE ADJ. ?
[YES] DONE
CUT FORCE
50gf 50gf
REDO ADJ. ?
YES [DONE]
Current correction
value
Value to be set
Andere Handbücher für LEC-300
4
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Roland Plotter Handbücher
Roland
Roland VT-200 Bedienungsanleitung
Roland
Roland LEC-300 Bedienungsanleitung
Roland
Roland SOLJET Pro 4 XR-640 Bedienungsanleitung
Roland
Roland VersaArt RE-640 Bedienungsanleitung
Roland
Roland DXY-1300 Installationshandbuch
Roland
Roland SF-200 Bedienungsanleitung
Roland
Roland DXY-800 Bedienungsanleitung
Roland
Roland VersaCamm SP-540V Bedienungsanleitung
Roland
Roland Camm-1 CX-24/12 Bedienungsanleitung
Roland
Roland VersaCamm VP-540 Bedienungs- und Wartungshandbuch
Roland
Roland SP-300 Bedienungsanleitung
Roland
Roland CX-500 Bedienungsanleitung
Roland
Roland Camm-1Pro Series Bedienungsanleitung
Roland
Roland CAMM-1 PRO Bedienungsanleitung
Roland
Roland VersaUV LEF-200 Betriebsanleitung
Roland
Roland Hi-Fi Express FP-740 Bedienungsanleitung
Roland
Roland SOLJET PRO4 XF-640 Bedienungsanleitung
Roland
Roland CAMM-1 PRO CM-500 Bedienungs- und Wartungshandbuch
Roland
Roland soljet pro4 xf 640 Bedienungsanleitung
Roland
Roland VP Series Bedienungsanleitung
