Rosemount 3308 Series Bedienungsanleitung

Quick Start Guide

00825-0500-4530, Rev AC

February 2017

Rosemount™VeriCase User Guide

Rosemount 3308 and 5300 Series Level Transmitters

with HART®and Modbus®

February 2017

Quick Start Guide

Rosemount VeriCase

1.0 Rosemount VeriCase overview

The Rosemount VeriCase is a mobile verification tool for the Rosemount 3308

and 5300 Level Transmitter with HART and Modbus communications.

Rosemount VeriCase Accuracy: Within ±1mm

The picture below identifies the parts inside the case that the user should be

familiar with before performing verification.

Note

The Rosemount VeriCase does not have any hazardous approvals certifications and should

only be used outside of such classified areas.

Figure 1. Rosemount VeriCase

A.Transmitter mount E. Power input

B. Terminal connections F. Ground connection

C. Cable switch G. USB cable connection

D. Temperature display

Contents

Rosemount VeriCase overview . . . . . . . . . . . . . . . . 2

Check Rosemount VeriCase and verification sheet 3

Performing a verification on a Rosemount 5300

transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Performing a verification on a Rosemount 3308

transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Generating a report . . . . . . . . . . . . . . . . . . . . . . . 8

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Quick Start Guide

February 2017

2.0 Check Rosemount VeriCase and verification

sheet

2.1 Check contents

Open the Rosemount VeriCase and check that it contains the following items;

USB stick containing

- User Instructions

-Microsoft

®Excel®workbook

- Calibration certificate

- HART modem drivers

- Rosemount Radar Master (for Rosemount 5300 Level Transmitter)

- Rosemount Configuration Tool (for Rosemount 3308 Wireless Level

Transmitter)

Printed calibration parameters

Printed certificate

110/220V Power Supply

12 VDC Power Cable

USB A-B cable

Two terminal connection cables with banana plugs and grippers

2.2 Check verification sheet

Open the Excel workbook found on the USB memory stick and check that the

following details in the workbook correspond to the printed certificate found

inside the Rosemount Vericase;

Serial number and calibration date

Cable lengths

Values for temperature correction table

2.3 Power-up the Rosemount VeriCase

The Rosemount VeriCase can be powered by either a 110V/220V power supply

or a 12VDC power adapter supplied with the Rosemount VeriCase. In order to

power-up the Rosemount VeriCase and connect to a transmitter head, follow

the steps below;

Connect the power cable

Screw the transmitter firmly onto the mount on the faceplate

Insert the terminal connectors in the '+' and '–' terminals on the faceplate and

attach the other ends to the terminals of the transmitter

Connect the USB A-B cable between your computer and the Rosemount

VeriCase.

In order to start the verification procedure the switch should be turned from

position '0' to position '1'.

February 2017

Quick Start Guide

3.0 Performing a verification on a Rosemount 5300

transmitter

3.1 Before you start

Open Rosemount Radar Master and record the serial number and firmware

revision of the device to be tested in the verification data tab of the

workbook. This information can be found in the device properties window in

the 'device' menu in Rosemount Radar Master.

3.2 Verification procedure

Note

Inches or millimeters should be selected for measurement units (there is a possible

inaccuracy of 1.25mm (0,05-in.) when inches are used for the display).

Configure device for verification

1. Save a backup file of the current device (this will need to be reloaded once

the verification is complete) by selecting Device -> Save Config to File…

2. In the Tank window under the Setup menu, configure the following

parameters for the transmitter that will be tested:

-Probetype:User Defined

- Probe length: longest cable length +50cm (20-in)

-ProbeImpedance:100 Ω

- Reference Pulse Amplitude: 3000mV

Make sure that the below parameters are set with the following values

- Propagation Factor: 1,000

- Tank Connection Length: 0

- Remote housing: None

-Probeangle:0

- Vapor DC: 1

- Measurement mode: Liquid product level, solid product level or

product level and interface level

Quick Start Guide

February 2017

Save these configuration changes and restart the device.

3.3 Verification test

1. Set the Cable Switch to position 1. Wait for the values to stabilize before

taking a reading from the Device Display window in Rosemount Radar Master.

2. Record the distance value, internal temperature of transmitter and

Rosemount VeriCase temperature.

3. Repeat the procedure in 2for all six cable lengths in the Rosemount VeriCase.

4. Once the verification is complete, restore the original configuration by

uploading the backup file to the transmitter. Select Device -> Upload Config

from File… and reload the file saved (see Configure device for verification ).

5. After the backup has been restored, disconnect power and communication

to the transmitter.

February 2017

Quick Start Guide

4.0 Performing a verification on a Rosemount 3308

transmitter

4.1 Before you start

Record the serial number of the device from the nameplate located on top of

the transmitter. Open Radar Configuration Tools and record the software

revision of the device to be tested in the verification data tab of the workbook.

This information can be found in the setup window under the info tab.

4.2 Verification procedure

Note

Inches or millimeters should be selected for measurement units (there is a possible

inaccuracy of 1.25mm (0,05-in.) when inches are used for the display).

Configure device for verification

1. Save a memory map from the current device (this will need to be reloaded

once the verification is complete) by selecting Memory Map from the

left-hand menu. Select Receive. When the values have finished loading

select File and Save Memory.

Note

When reading a measurement value remember that the repeatability of a Rosemount

3308 is ± 2mm (0,08-in.)

2. In the Setup window under the Setup menu, configure the following

parameters for the transmitter that will be tested:

Probe type: User Defined

Quick Start Guide

February 2017

Probe length: longest cable length +50cm (20-in)

Probe Impedance: 100 Ω

Reference Pulse Amplitude: 30mV

Make sure that the below parameters are set with the following values

Propagation Factor: 1,000

Tank Connection Length: 0

Probe angle: 0

Vapor DC: 1

Measurement mode: Liquid product level or product level and interface

level

- Save these configuration changes and restart the device.

4.3 Verification test

1. Set the Cable Switch to position 1. Open Monitor in the left-hand menu.

Select Product Distance and Electronics Temperature and press play. Wait

for the values to stabilize before taking a reading from the Device Display

window in Rosemount Radar Master.

2. Record the Product Distance value, Electronics Temperature and

Rosemount VeriCase temperature.

3. Repeat the procedure in 2for all six cable lengths in the Rosemount VeriCase.

4. Once the verification is complete, restore the original configuration by

uploading the memory map to the transmitter. Select File from the top

menu and Open Memory Map. When the values have loaded select Send to

reload the configuration file saved (see Configure device for verification ).

February 2017

Quick Start Guide

5. After the configuration has been restored, disconnect communication to the

transmitter.

5.0 Generating a report

Once testing is complete, a report can be generated from the Excel workbook. It

is possible to generate a verification report and/or a Q4 certificate by selecting

the corresponding generate report buttons located at the bottom of the

verification data tab and the Q4 data tab respectively. In order to generate a Q4

certificate the analog output of the transmitter under verification should be

tested at 4mA, 12mA and 20mA and the results saved in the Q4 data tab before

generating the certificate.

Quick Start Guide

February 2017

6.0 Appendix

6.1 FAQs

Q: Can verification of a FOUNDATION™Fieldbus transmitter be performed using

the Rosemount VeriCase?

A: Yes, but an external FOUNDATION Fieldbus modem (and power supply if

Explosion proof) will be required as a FOUNDATION Fieldbus modem is not built in

to the Rosemount VeriCase.

Q: What do I do if a device fails?

A: Check that the device is correctly configured and repeat the test. If the results

are the same, log a support request in the same way as you would with other

level instrumentation, providing all details of the testing, including results and

backup files.

Q: How do I know if a device has passed the test?

A: Refer to the Rosemount 5300 PDS for accuracy specifications. A device has

passed if the final result is inside the combined accuracy for the Rosemount 5300

and the Rosemount VeriCase as shown in the Excel workbook.

Q: What does the offset value in the results mean? Do I need to adjust anything

in the guided wave radar settings?

A: This is the offset generated from using the Rosemount VeriCase rather than a

probe. This is compensated for automatically and there is no need for manual

adjustments.

Q: Why is the transmitter rebooted every time I switch cable length?

A: This is so the measurement can be reset to lock on to a new value without

echo logic or filtering affecting the measurement.

Q: How often should Rosemount VeriCase be calibrated?

A: Once a year or if calibration seals have been broken.

Q: The calibration of the Rosemount VeriCase has expired. What do I do?

A: Every world area has an assigned administrator to coordinate recalibrations.

Contact your administrator for further instructions.

Global Headquarters

Emerson Automation Solutions

6021 Innovation Blvd.

Shakopee, MN 55379, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

RFQ.RMD-RCC@Emerson.com

North America Regional Office

Emerson Automation Solutions

8200 Market Blvd.

Chanhassen, MN 55317, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

RMT-NA.RCCRFQ@Emerson.com

Latin America Regional Office

Emerson Automation Solutions

1300 Concord Terrace, Suite 400

Sunrise, FL 33323, USA

+1 954 846 5030

+1 954 846 5121

[email protected]

Linkedin.com/company/Emerson-Automation-Solutions

Twitter.com/Rosemount_News

Facebook.com/Rosemount

Youtube.com/user/RosemountMeasurement

Google.com/+RosemountMeasurement

Standard Terms and Conditions of Sale can be found on the Terms

and Conditions of Sale page.

The Emerson logo is a trademark and service mark of Emerson

Electric Co.

Rosemount and Rosemount logotype are trademarks of Emerson.

HART is a registered trademark of the FieldComm Group.

Modbus is a registered trademark of Gould Inc.

FOUNDATION Fieldbus is a trademark of the FieldComm Group.

Excel and Microsoft are a registered trademarks of Microsoft

Corporation in the United States and other countries.

All other marks are the property of their respective owners.

Europe Regional Office

Emerson Automation Solutions

Neuhofstrasse 19a P.O. Box 1046

CH 6340 Baar

Switzerland

+41 (0) 41 768 6111

+41 (0) 41 768 6300

[email protected]

Asia Pacific Regional Office

Emerson Automation Solutions

1 Pandan Crescent

Singapore 128461

+65 6777 8211

+65 6777 0947

Enquiries@AP.Emerson.com

Middle East and Africa Regional Office

Emerson Automation Solutions

Emerson FZE P.O. Box 17033

Jebel Ali Free Zone - South 2

Dubai, United Arab Emirates

+971 4 8118100

+971 4 8865465

RFQ.RMTMEA@Emerson.com

Quick Start Guide

00825-0500-4530, Rev AC

February 2017

*00825-0500-4530*

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rosemount Messgerät Handbücher

Rosemount

Rosemount 702 Bedienungsanleitung

Rosemount

Rosemount TankRadar Rex 3900 Series Benutzerhandbuch

Rosemount

Rosemount 8712D Series Bedienungsanleitung

Rosemount

Rosemount 3051S Series Bedienungsanleitung

Rosemount

Rosemount TankRadar Pro Stücklistenhandbuch

Rosemount

Rosemount 3300 Series Konfigurationshandbuch

Rosemount

Rosemount SOLU COMP II Bedienungsanleitung

Rosemount

Rosemount Series 8700 Bedienungsanleitung

Rosemount

Rosemount 1054A pH Bedienungsanleitung

Rosemount

Rosemount FCL Bedienungsanleitung

Rosemount

Rosemount 8714D Bedienungsanleitung

Rosemount

Rosemount 405 Bedienungsanleitung

Rosemount

Rosemount 3095FB Bedienungsanleitung

Rosemount

Rosemount 8800D Series Bedienungsanleitung

Rosemount

Rosemount 951C Bedienungsanleitung

Rosemount

Rosemount 4500 Bedienungsanleitung

Rosemount

Rosemount 6888Xi Bedienungsanleitung

Rosemount

Rosemount 1054B Bedienungsanleitung

Rosemount

Rosemount 8712E Bedienungsanleitung

Rosemount

Rosemount TankRadar Rex RTG 3920 Bedienungsanleitung

Rosemount

Rosemount 3051S Series Bedienungsanleitung

Rosemount

Rosemount P330 Bedienungsanleitung

Rosemount

Rosemount 5401 Bedienungsanleitung

Rosemount

Rosemount 8712EM Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung