Rowenta EFFECTIVE DZ1700U1 Bedienungsanleitung

Appliance description

1 Spray button

2 Burst of steam and

vertical steam button

3 Variable steam control with

Auto Steam and Self Clean

Function

4 Auto-off light

5 Thermostat light

6 Temperature control dial

7 Water filling inlet

8 Spray nozzle

9 Cord

10 Cord support

11 Water tank with maximum

water level indicator

12 Soleplate

NOT DZ1700 1103480249 13/12/05 17:06 Page 1

IMPORTANT SAFETY INSTRUCTIONS

When using your iron, basic safety precautions should always be follo-

wed,including the following : Read all instructions before using the iron.

• Use iron only for its intended use.

•To protect against a risk of electric shock, do not immerse the iron in

water or other liquids.

•The iron should always be turned to Minimum (Min) before plugging

or unplugging from outlet. Never yank cord to disconnect from outlet,

instead grasp plug and pull to disconnect.

• Do not allow cord to touch hot surfaces. Let iron cool completely

before putting away.

• Loop cord loosely around iron when storing. Always disconnect iron

from electrical outlet when filling iron with water, emptying iron or

when not in use.

• Do not operate iron with a damaged cord or if the iron has been

dropped or damaged.To avoid the risk of electric shock, do not

disassemble the iron, ship it to the nearest authorized Rowenta

Appliance Service Center for examination and repair. Incorrect

reassembly can cause a risk of electric shock when the iron is used.

• Close supervision is necessary for any appliance being used by or

near children. Do not leave iron unattended while plugged in or on an

ironing board. Do not direct steam at people, animals or iron clothes

while they are being worn.

• Burns can occur from touching hot metal parts, hot water or steam.

Use caution when you turn a steam iron upside down there may be hot

water in the reservoir.

•The use of accessory attachments is not recommended by Rowenta

Appliance Company and may result infire, electric shock or personal injury.

SPECIAL INSTRUCTIONS

1.This is either a 1600 / 1700 watt appliance.To avoid an overload, do

not operate another high wattage appliance on the same circuit.

2. If an extension cord is absolutely necessary, the marked electrical

rating of the extension cord should be at least as great as the electri-

cal rating of the appliance. Cords rated for less amperage may over-

heat. Care should be taken to arrange the cordso that it cannot be

pulled or tripped over.

3. Your Rowenta appliance is intended for household

SAVETHESE INSTRUCTIONS

NOT DZ1700 1103480249 13/12/05 17:06 Page 2

Before Use

- Please read all of the Instructions for Use and

the Important Safety Guards carefully.

- Remove all packaging from the iron.

- Remove the soleplate protector.

- It is normal for a small amount of smoke and

a light odor to be produced the first time it is

used.This will quickly disappear.

- Particles may emit from iron during first use.

They are not harmful and should disappear

after the iron has been used.

Helpful Hints

- When ironing, start with fabrics that require a low tempera-

ture setting (•) and finish with those which need the highest

temperature (•••).

- Mixed fiber fabrics should be ironed on the temperature for

the most delicate fabrics. For example a shirt that is 60 %

cotton and 40 % polyester should be ironed at the (•) set-

ting for synthetics.

- If spray starch is used, spray it onto the reverse side of the

garment. Allow starch to penetrate before ironing by set-

ting garment aside for 30 seconds.

- For best results, use a mesh type ironing board to allow

excess steam to escape.

- For delicate fabrics, we recommend carrying out a test on

an unobtrusive area of the garment such as an inner seam.

- Adhere to manufacturer recommendations on garment label.

3 Way Auto-Off

- If the iron is not moved while it is plugged

in, an internal safety switch will turn it off.

- It will turn off in 8 minutes if left vertically or

in 30 seconds if left on its soleplate or tipped

over. A red flashing light indicates that the

auto-off has been activated.

- To switch the iron on again, move the iron

or gently shake it.

Auto off is not on/off switch.

Always unplug iron when it is not use.

Filling with Water

- Ensure the iron is unplugged.

- Slide the variable steam control completely

to the left.

- Rest the iron on heel and tilt it forward

approximately 1 inch.

- Fill with water (containing no additives) to

the max mark on the water tank. We recommend

using a water pitcher rather than filling under

the tap. Iron holds approximately 8.5 oz. of

water.

- If you need to add water during ironing,

UNPLUG the iron and follow the steps above.

- Ensure iron heats back to temperature after-

wards, that means thermostat light will go out.

NOT DZ1700 1103480249 13/12/05 17:06 Page 3

Water Recommendations

Tap water

Rowenta irons are designed to be used with REGULARTAP

WATER (up to 12 grains of hardness). If your water is harder

than this, Rowenta recommends mixing half tap water with

half distilled water which reduces the hardness; or just use

inexpensive bottled spring water. Never use 100% distilled

water since this can cause the iron to spit and leak.

Softened water

There are many types of household water softeners and the

water from many of them is perfectly acceptable for use in

an iron. However, some types of softeners, particularly those

that use chemicals such as salt, can cause the iron to leak or

spit during use. If you experience this type of problem, we

recommend that you try using inexpensive bottled spring

water or untreated tap water. Never use 100% pure distilled

water.

Once you have changed water it will take several uses to

correct the problem. Rowenta recommends trying the steam

function for the first time on an old towel or cloth to avoid

damaging your clothes.

Iron and other impurities

If your water supply contains large amounts of iron or organic

matter, these minerals can collect inside the iron and eventually

appear as brown stains. If you experience these problems

Rowenta recommends using inexpensive bottled spring water.

Never use 100% pure distilled water

Always remember:

Battery water and water containing additives (such as starch,

perfume or fabric conditioner) may not be used. Such additives

can affect the properties of the steam and, at high temperatu-

res, can form deposits in the steam chamber, which will mark

the laundry when they are emitted through the steam vents.

For this reason descaling liquids should not be used.

Selecting the Temperature

- Set the temperature control dial according to

the fabric you are ironing. Check the garments

label for appropriate setting.

We recommend using the chart below as a

guide.

Light will be on as iron is heating. When light goes out iron is ready

to use. When heating a cold iron, please allow thermostat to cycle

twice before use (thermostat light will go on and off twice).

Ironing label Fabric

Synthetic fibres e.g.

viscose, polyester

silk, wool

cotton, linen

Temperature

control

NOT DZ1700 1103480249 13/12/05 17:06 Page 4

Steam Ironing

WARNING !

•Never iron or steam clothes while they are being worn.

• Before ironing for the first time fill iron and allow to heat.

• The iron should be allowed to emit steam for 1 to 2 minutes

while pressing the burst of steam button a few times to

remove any impurities.This should also be done if iron is

not used regularly.

Steam is only produced when the temperature dial is set to the

shaded area (after •• setting).

Burst of steam

- This feature is ideal for removing stubborn

wrinkles or pressing in sharp creases in hori-

zontal use. When the temperature control is

set to the steam zone (after ••) the burst of

steam can be used by pressing the burst of

steam button. Leave an interval of 4 seconds

between bursts.

Vertical Steam

The iron can also be used vertically.

- This is especially useful for getting creases

out of hanging clothes, curtains, tapestries, etc.

- To steam vertically, press the burst of steam

button while holding iron in the upright position.

Warning! Never iron clothes while they are being worn.

Dry Ironing

- To iron without steam, slide the variable

steam control lever to the position.

- We recommend dry ironing with an empty

tank.

- Set the temperature for the type of material to

be ironed (•, •• or •••).

Auto Steam

- For steam output to be automatically

adjusted to the soleplate temperature, turn

the steam control to the position.

NOT DZ1700 1103480249 13/12/05 17:06 Page 5

Spray Setting

- This feature is ideal for stubborn wrinkles or

set in creases.

- Ensure there is water in the tank then press

the spray button.

- Do not spray silk.

Anti-Drip System

- In order to produce steam, all irons require a high tempera-

ture. If the soleplate is not hot enough some of the water will

not turn to steam and can spit or leak from the soleplate.

The Anti-Drip system automatically switches off the steam

when ironing at low temperatures to prevent spitting.

Anti-Calc System

- Minerals in water can build up in the steam chamber.

The Anti-Calc system contains a special material that

neutralizes the harmful minerals.This system is designed

to extend and maintain the high steam performance of the

iron.The cartridge is not replacable.

Self Clean

Warning! Do not use descaling agents.They can damage the

lining of the steam chamber.

This feature allows loose mineral deposits and other impurities

to be flushed from the soleplate.

Self Clean should be carried out occasionally and at least once

a month.

- Fill the iron with tap water to the max mark

on the water tank.

- Be sure that variable steam lever is set to m

minimum.

- Stand the iron onheel and plug in.

` - Set thermostat to ••• setting.

- Once heated, unplug iron.

- Hold iron horizontally over the sink with the

soleplate pointing away from body.

- Move the variable steam lever completely to

the right and hold in the self clean position

for one minute.

Warning! Doing this will cause steam and hot water to be

ejected from the soleplate.Take all proper precautions and

hold iron away from body.

- Move the iron gently back and forth and side to side until all

water has run through plate.

- Carefully wipe all water and material from the soleplate with

an old towel, as the water and minerals can stain the sole-

plate (although this has no effect on glide or performance).

ANTI

CALC

ANTI DRIP

NOT DZ1700 1103480249 13/12/05 17:06 Page 6

Warning! Iron and soleplate may still be very hot. Exercise care

while wiping.

- Place iron on heel and leave to cool.

Before using iron after self cleaning, test steam and burst of

steam on an old towel or cloth than can be discarded.

Vapodur Valve

To ensure the iron continues to steam efficiently, open and

close the valve a few times after each use. This is done by

moving the variable steam control lever left to right a few

times.

After Ironing

1. Turn the temperature dial to the min setting. Slide the steam

lever to the no steam position .

2. Unplug the appliance.

3. Place the iron on its heel and allow to cool completely.

4. Empty water from the appliance before storing.

We recommend emptying the iron when not in use.

5. To protect the soleplate, we recommend storing iron on its

heel.

Cleaning and Maintenance

When cold and unplugged, the iron can be cleaned with a

damp cloth and wiped dry.

Never use household cleaners or solvents.

Cleaning the soleplate

Rowenta soleplates have excellent non-stick properties and can

be wiped clean when cold.

- In normal use a draggy coating may build up on the soleplate

(starch, detergent build-up, burnt synthetic fibers).

This can easily removed by using the Rowenta Soleplate Kit

or a quality hot iron soleplate cleaner available at most

stores.The Rowenta kit is also available through our website:

www.rowentausa.com.

- To prevent scratching of the soleplate, do not iron over sharp

objects (zippers, etc.). Do not place the iron on rough surfaces,

e.g. metal iron support, which may scratch the soleplate.

NOT DZ1700 1103480249 13/12/05 17:06 Page 7

Troubleshooting

Issues

Not properly plugged

in.

The temperature

control is set too low.

Auto-off has engaged

(depending on model).

There is insufficient

water in the tank.

Iron is not set to a

steam setting.

The Anti-drip function is acti-

ve, depending on model.

Water may need to be

changed due to hard-

ness or organic matter.

Garment has not been

rinsed sufficiently.

Over use of burst but-

ton.

Distilled or softened

water being used.

Overfilled.

Auto-off has engaged

(depending on model).

Starch use.

Burnt material.

Ironing at too high

temperature.

Priming may be neces-

sary on first use.

Check that iron is plugged

correctly.

Set the temperature control to a

higher temperature.

Move iron or shake it gently to

reactivate.

Fill the water tank.

See section called “Steam

Ironing”.

Wait for the soleplate to reach the

correct temperature.

See section “Water recommenda-

tions”. Switch to spring water or

mix tap water with distilled water.

Ensure garments are rinsed tho-

roughly to remove any detergent

desposits or chemicals on new

garments.

Allow more time between each

burst.

See section “Water recommenda-

tions”. Switch to spring water or

mix tap water with distilled water.

Do not fill past max line on tank.

Be sure to close the cover at

filling inlet, depending on model.

Move iron or shake gently to

reactivate.

Spray reverse side of fabric and

allow starch to penetrate.

Be sure to set temperature

according to fabric being ironed.

Fill with water.

Hold cold iron horizontally.

Place finger over the spray nozzle

to create a vacuum.

Press the spray button 4 to 5

times.

Remove finger from nozzle, press

spray button a few more times.

Possible causes Solutions

Iron does not

heat.

Not enough

steam.

Iron is emitting a

brown or white

substance.

Iron is leaking.

The Auto-off light

is flashing.

Build up on the

soleplate.

Spray function

does not work.

If troubleshooting does not assist, before consulting the retailer

regarding their return / exchange policy, please telephone

consumer service at: 781-396-0600.

NOT DZ1700 1103480249 13/12/05 17:06 Page 8

All Rowenta products are warranted for 1 year from date

of purchase against defects in material and workmanship.

During this period, any Rowenta product that, upon

inspection by Rowenta, is proved defective, will be repaired

or replaced, at Rowenta's option, without charge to the

customer. If a replacement product is sent, it will carry the

remaining warranty of the original product. This warranty

does not apply to any defect arising from a buyer's or

user's misuse of the product, negligence, failure to follow

Rowenta's instructions, use on current or voltage other

than stamped on the product or alteration or repair not

authorized by Rowenta. Repair or disassembly by anyone

other than a Rowenta authorized service center will void

the warranty. THE WARRANTIES SET FORTH HEREIN ARE

EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE OR USE, ARE MADE BY ROWENTA

OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO

THE PRODUCT. If you believe your product is defective,

bring the product (or send it, postage prepaid) along with

proof of purchase to the nearest authorized Rowenta

Service Center (see below). If you send the product, please

include a letter explaining the nature of the claimed defect.

In the interest of improving products, Rowenta reserves theright

to change specifications without prior notice.

LIMITED WARRANTY

NOT DZ1700 1103480249 13/12/05 17:06 Page 9

Rowenta

196 Boston Avenue

Medford, MA 02155

Tel. : (781) 396-0600

www.rowentausa.com

OFFICE LOCATION ONLY.

To service product see service center information below.

If your appliance needs service, ship the product to your nearest

regional service center. Be sure to put your name on the outside

of shipping box (no P.O. boxes please). If in warranty, Rowenta will

repair or replace product at their discretion. If the product is out of

warranty you will be advised of the cost of repair before any work

begins.

Our main service centers ar listed below :

Turnpike Appliance Authorized Appliance

3495A Lawson Blvd. 1644 West Ogden Ave.

Oceanside, NY 11572 Downers Grove, IL 60515

516-483-5596 630-852-1550

Service center information is subject to change. Please visit our

website at www.rowentausa.com or call our service center

information line at 781-306-4620. The information line provides

current service center information and listings in California.

Rowenta Werke GmbH, 63016 Offenbach am Main

NOT DZ1700 1103480249 13/12/05 17:06 Page 10

Inhaltsverzeichnis

Sprachen:

Andere Rowenta Eisen Handbücher

Rowenta

Rowenta ECO INTELLIGENCE DW6010M1 Bedienungsanleitung

Rowenta

Rowenta PERFECT STEAM DG8535F0 Bedienungsanleitung

Rowenta

Rowenta Ultra Professional Ultra Professional Steam... Bedienungsanleitung

Rowenta

Rowenta DW5000 Bedienungsanleitung

Rowenta

Rowenta EFFECTIVE DX1931U5 Bedienungsanleitung

Rowenta

Rowenta DA1560U1 Bedienungsanleitung

Rowenta

Rowenta Expertise Bedienungsanleitung

Rowenta

Rowenta DX1550 Bedienungsanleitung

Rowenta

Rowenta Professional DW8007D1 Bedienungsanleitung

Rowenta

Rowenta SMART STEAM Bedienungsanleitung

Rowenta

Rowenta DX16XX Bedienungsanleitung

Rowenta

Rowenta 42449 Bedienungsanleitung

Rowenta

Rowenta DW5121D1 Bedienungsanleitung

Rowenta

Rowenta Freemove DE5 Series Bedienungsanleitung

Rowenta

Rowenta DW9220 Bedienungsanleitung

Rowenta

Rowenta Sew 'n' Press Sew 'n' Press Steam Iron Bedienungsanleitung

Rowenta

Rowenta ACCESSTEAM DW23 Bedienungsanleitung

Rowenta

Rowenta SOFT DX2500D1 Bedienungsanleitung

Rowenta

Rowenta DA1511 Bedienungsanleitung

Rowenta

Rowenta DW9216 Bedienungsanleitung

Rowenta

Rowenta DW7000 Bedienungsanleitung

Rowenta

Rowenta DW9220 Bedienungsanleitung

Rowenta

Rowenta Steamium DW9020 Bedienungsanleitung

Rowenta

Rowenta DW5000 Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung