Royal Metal upright Bedienungsanleitung

OWNER'S MANUAL

METAL

Operating and Servicing Instructions

UPRIGHT

Please read

these instructions

carefully before

usingyour

uprightvacuum.

Let us helpyou

put your vacuum

together or

answer any

questions, call

1-800-321-1134

(U.S.A.).

1-800-661-6200

(Canada).

1-880957-001

Rev.

12/98

CONGRATULATIONS!

You are now theproud owner of a Royal vacuum cleaner. We trustyour new

purchase will bring you many hours of satisfaction.

Our companydesigned anddeveloped thisproduct, andit is manufacturedby

us in Cleveland, Ohio. We takegreat care to ensure top quality,but an occasion-

al mistakemay occur; thus,please check to be sure all components are included

in your cartonand that each is free from defects. Please call us shouldyou need

assistance.

In order to assistour marketing efforts,we wouldappreciatethereturn of your

completedwarranty/registrationcard. Please feel free to add any comments.

We are veryproud of our products and hope that you are equally satisfied with

their quality and performance. For all your cleaning needs, remember Royal

because.

."WE BUILD-EM TO LAST".

*THISAPPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY

IMPORTANT SAFETY INSTRUCTIONS

SAVETHESE INSTRUCTIONS

When using an electrical appliance, basic precautions should always be fol-

lowed, includingthe following:

-READALL INSTRUCTIONSBEFOREUSINGTHISAPPLIANCE

.ALWAYS FOLLOWTHESE SAFETY INSTRUCTIONS

WARNING:TO REDUCETHE RISK

OF FIRE, ELECTRIC SHOCK,

OR INJURY:

Do not leave appliance when

plugged in. Unplugfrom outlet

when not in use and before

servicing.

Do not useoutdoors or on wet

surfaces.

Do not allow to be used as a

toy. Close attention is neces-

sary when used by or near

children.

Use only as described in this

manual. Useonly Royal's rec-

ommended attachments.

Do not use with damaged

cord or plug. If appliance is

not working as it should, has

been dropped, damaged, left

outdoors, or dropped into

water, return it to a service

center.

Do not pull or carry by cord,

use cord as a handle, close a

door on cord, or pull cord

around sharp edges or cor-

ners. Do not run appliance

over cord. Keep cord away

from heated surfaces.

Do not unplug by pulling on

cord. To unplug, grasp the

plug, notthe cord.

Do not handle plug or appli-

ance with wet hands.

Do not put any object into

opening. Do not use with any

opening blocked; keep free of

dust, lint, hair, and anything

that may reduce air flow.

Keep hair, loose clothing, fin-

gers, and all parts of the body

away from openings and mov-

ing parts.

Do not pick upanything that is

burning or smoking, such as

cigarettes, matches, or hot

ashes.

Do not use without dust bag

and/or filters in place.

Use extra care when cleaning

on stairs.

Turn off all controls before

unplugging.

Do not useto pick upflamma-

ble or combustible liquids

such as gasoline

use in

areas where they may be pre-

sent.

Do not use an extension cord

with this vacuum cleaner.

Store the vacuum cleaner

indoors. Put the vacuum

cleaner away after use to pre-

vent tripping accidents.

Always turn off the vacuum

cleaner before connecting or

removingthe hose.

Using improper voltage may

damage motor and injure

user.

WARNING:

To reduce the risk of electric shock, this appliance has a polarized plug (one

bladewider than the other). This plugwill fit in a polarizedoutletonly oneway.

Ifthe plug does not fit fully in the outlet, reversethe plug. If itstill does notfit,

contact a qualified electrician to install the proper outlet. Do not change the

plug in any way.

WARNING

Electricalshock could occur if

usedoutdoors or on wet surfaces.

FAMILIARIZEYOURSELF THESE FEATURES

FingertipToggle Switch-conveniently locatedfor quick control.

Eyelet of Upper Cord Hook

*Special Bag Assembly-Outer bag resists wear and has full length

metal zipper for easy access to top-filling "Toss-Out" paper filter bag OR

Cotton top-filling shake-outbag.

Handle Fork

Bag Coupling

Exhaust Couplet

*WheelArrangement

Heavy DutyVinyl Hand Grip-curvedto fit your handcomfortably.

*Strong Metal Cord Hooks

10.

ULApproved Power Cord-permitswide range cleaning.

11.

Adjustable Handle-made of chrome-platedtubular steel. Centered on

motor housingfor balanceand maximum maneuverability.

12.

Wing Nut

13.

Handle Lock-holds handle securely in

positions.

14.

*Headlight-hingedhousingwith protectivevinyl bumperguardand exclu-

sive deodorizing, demothing, sanitizer chamber

standard, brilliant

headlightas shown.

15.

*Patented"Adjust-0-Rite" Belt Cover Plate-eliminatesguesswork

for proper nozzle setting.

16.

Wrap AroundVinyl Nozzle Bumper-protectswalls and furniture.

17.

Belt Lifter Lip

18.

Belt Lifter Base

19.

Cast Aluminum Nozzle, Fancase, and Motor Housing

20.

Adjustable Revolving Brush, beater bar or double helical brush

21.

Metal Rug Nozzle Guard

22.

*"Rite-Hite" Adjustor Knob-lets you set nozzle to exact height for

carpet plushness.

23.

*Five Position Height Adjustor-lets you set the nozzle at five different

carpet heightswith the touch of your toe.

*Styleof feature may differ accordingto model.

GETTO KNOWYOUR NEWVACUUM CLEANER

Your new upright has many special features. All were designed for effortless

cleaning because suction alone does not make a vacuum cleaner clean.

There mustbe"air movement"to have cleaningpower. That's why the nozzle

has deep, wide air vents at both ends. These vents permit air to circulate

between the nozzle and carpet at all times; the result

...

our special self-pro-

pelling CushionaireTMCleaning. Your new upright also has exclusive curved

fan bladeswhich create more air volume per minuteat less motor speed than

straight blades. This means more efficient carpet cleaning and less electrici-

ty consumption;thus you save time and money.

EASY

ASSEMBLE

Note: Do not connect cleaner to electrical outlet until it is assembled.

Assemble the Handle

(Diagram

1. Slide the upper and lower handle

sections together, aligningthe

square or round holes on both

handle sections.

Fromthe literature pack, get the

square neck curved head bolt,

curved washer, and 711

nut.

lnsert square neck curved head

bolt through

square

aligned hole opening, until curved head is flush

with handle. WARNINGDO NOT FORCE HANDLE BOLT. MAY SEVER

CORD, COULD CREATE SHOCK.

Place curved washer over threaded end of bolt and tighten 7116"nut with

appropriatetool (tool not included).

All except models below

Remove wing nut and bolt from fork completely.

lnsert handle and power cord into the fork. Tighten.

Models withapigtail:

Loosenthe largewing nut on the handlefork locatedon

the motor unit. Insetthe handle into the fork and tighten the large wing nut.

Connectthe cords at the handlebottomandthe motor unit. Windthe extra-

long electrical cord over the cord hooks when cleaner is not being used.The

electrical cord is ~ermanentlvattachedto the upper part of the handle and a

short connector plug is at theother end.

Checkto be sure the belt is in place.

If not, follow these easy steps:

Attach the Belt

1. Remove "Adjust-0-Rite" belt cover*

or rotate the grey rubber nozzle

cover* from front of cleaner.

(Diagram 1)

Insert belt lifter tool through belt

loop, beingsure to hookbelt around

the lip of the belt lifter tool from the

left (Diagram

2).

Usingthe tool as a

pry bar, slip the belt onto the motor

shaft until the belt lifter base meets

the shaft. Gentlyturn the tool to the

right (clockwise) to insure proper

belt placement. Removetool.

The front of the belt will be to your

right when installed properly

(Diagram

3).

Snap "Adjust-0-Rite"

belt cover* or rotatethe grey rubber

nozzle cover* over the belt access

opening.

*Featuremay differ accordingtomodel.

Attach the Bag

Placethe bagcoupling over the exhaust outlet of the machine. Slide iton and

twist to the right to lock. Attach the top of the bag by snapping the hook on

the bag chain into the eyelet on the upper corb hook.

Your

New

Upright

Ready

Go!

Plug

in the Cleaner

Plugthe electricalcord into your most convenient outlet, makingsure the volt-

age indicated on the serial number plate of your cleaner is the same as your

electrical source.

Set the Nozzle Height

Infinite Height Settings:

Lets you clean every type of carpet. Your new

uprightwill glide easily over your carpets and rugs, "air-lifting"them as it vac-

uums.

To adjust the nozzle on models with

an "Adjustor KnobW,(l)turnthe "Rite-

Hite" knob (located above rear

wheels) counter-clockwise to raise

the nozzle off the carpeting. (2)Turn

on the vacuum cleaner. Use the fin-

ger switch convenientlylocatedon the

handle. Push down to start--up to

stop. @)Now,graduallyturn the "Rite-

Hite"knobclockwiseto lower the noz-

'Ie

the

when

the

I*/Ju//

knob

nof

com-i

"Adjust-0-Rite"button pops IN.

At this setting the nozzle is at the

mercialmodels.

exact height to do the best cleaning

job. As you clean from carpets to rugs and across bare floors, check the

"Adjust-0-Rite"button and adjust the cleaner accordingly. For high shag car-

peting: adjust for a gentle sweeping action and disregard"Adjust-0-Rite"but-

ton.

Five

Position Height Settings:

Adjust carpet settings for floor surfaceto

be cleaned. Set the nozzle at five different carpet heights with the touch of

your toe. The illustrationsshow the height adjustor in the lowest and highest

positions. The setting should be low enough for effective cleaning, yet high

enough that the cleaner is not difficult to push.

Note: Ifcleaner isdifficult to push, adjust to a highercarpet settingheight.

SETTINGS

FOR

LOW PILE

RELEASETHE CORD

On models equippedwith a quick cord release, simply

pushthe quick releasecord hookforward or backward

until it is upside down. The cord will slide off easily.

Return quick release cord hook to its upright position

so it isready to storethecordwhen you completeyour

cleaningtasks.

TILT NOZZLE

To clean throw rugs andcarpets with fringed edges, push handledown below

normal operating position thereby raising the nozzle (so fringe or binding will

not catch). Throw rugs should be cleaned by working from the center toward

and over the fringe, tilting the nozzle upward and over the edge of the carpet.

LOWER HANDLE

To clean carpeted stairways and under low furniture and beds, startwith han-

dle back in tilting position. Then lift handle lock lever (locatedwhere handle

meets motor housing)with your toe and lower handleto floor. For stairways,

depress handle lock lever so cleaner can be held in a horizontalposition. To

raise handle, release handle lock lever.

PAPER BAG REMOVAL AND INSTALLATION

(disconnect machinefrom electrical outlet prior to performing

any

maintenancefunction).

"TYPE A" PAPER BAGS

Your top-fillingpaperbagallowsdirt anddust

to fall into the storage area, keeping the

intake channel cleaner at all times. When

the paper bag fills to the level indicated,

unplug the cleaner and replace the bag.

Check your toss out bag occassionally by

feelingfor the dirt level.

clean bag assures

maximum cleaning efficiency and prolongs

the lifeof the machine.

"TYPE

PAPER BAGS

Pull cardboard connector of paper bag

away from top-fill tube and dispose of

used paper bag.

Place new paper bag into cloth bag.

Keep cardboard connector facing top-fill

tube.

Tuck paperbagdown intocloth bagas far

as possible.

Push cardboard connector over top-fill

tube opening as far as possible.

Close outer bag.

If your cleaner has the wide-openingcloth "shake-out"bag, follow these

directions when dirt reaches the half-fullpoint:

Unhook bag at the top and remove from cleaner by turning inlet coupling

counter-clockwise.

Turn bagupside down and shake vigorously until dirt settles at bag clamp

end.

Slide off bagclamp and empty dirt onpapersspreadon floor or in suitable

waste container.

Note: Regardlessof type of bag, empty frequentlyfor maximumcleaningeffi-

ciency and machine life.

BRUSH AND BELT

REPLACEMENT AND INSTALLATION

(UNPLUG CLEANER)

If you have occasionto remove the revolvingbrush, either for makingadjust-

ments or for replacing belt:

Pull knob to remove the "Adjust-0-Rite"belt cover* or rotatethe grey rub-

ber nozzle cover* on the front of the nozzle.

Lift the belt off the drive shaft with belt lifter tool (reverse directions for

attaching belt shown on page

6).

Removethe metalguardon the bottomof the nozzle. Removethe beltand

brush.

To adjustthe height of the brush roll or to changethe brush, pullthe brush

out of the nozzle

Slip the belt over the revolving brush before brush is

put into the new position.

Ball bearing brush rolls have color-coded endcaps for easy replacement.

When the brush is new, the color of the endcap must matchthe color marked

on the inside of the nozzle.

For

ALL

brush rolls, arrows on brush

roll and nozzle guard must

match

(Diagram

1).

Diagram

The belt is then placedover the motor drive shaft as described in "Attach

Belt" on page

Place the belt so that the right hand side of the belt is

nearest to you.

If the belt dislodges when

you

turn the unit

"on",

the belt

on "backwards".

Reverse the belt, twist and place over motor drive

shaft. Replaceround"Adjust-0-Rite"plate* or grey rubber nozzle cover*.

CAUTION: Never placeany fingers, tools, etc. in nozzleor belt areawhile the

unitis operating. The"Adjust-0-Rite"plate*or grey rubber nozzlecover* must

be securely installedwhenever operatingthe unit without attachments.

*Featuremay differ according to model

Inhaltsverzeichnis

Sprachen:

Andere Royal Staubsauger Handbücher

Royal

Royal m7020 Bedienungsanleitung

Royal

Royal Vacuum Cleaner Bedienungsanleitung

Royal

Royal VERSO wet & dry Bedienungsanleitung

Royal

Royal Azury Bedienungsanleitung

Royal

Royal Centrino Cleancontrol Bedienungsanleitung

Royal

Royal Dust Devil Deluxe Bedienungsanleitung

Royal

Royal LEXON S20 Bedienungsanleitung

Royal

Royal RY6826 Bedienungsanleitung

Royal

Royal cnister ry3000 Bedienungsanleitung

Royal

Royal Infinity VS8 Loop Bedienungsanleitung

Royal

Royal Prince Bedienungsanleitung

Royal

Royal CAN VAC Bedienungsanleitung

Royal

Royal LEXON S17 Bedienungsanleitung

Royal

Royal Tempo Bedienungsanleitung

Royal

Royal Vacuum Cleaner Bedienungsanleitung

Royal

Royal Prince Bedienungsanleitung

Royal

Royal Dirt Devil Derby Bedienungsanleitung

Royal

Royal Infinity UP1LIGHT Bedienungsanleitung

Royal

Royal Centrino X3.1 Bedienungsanleitung

Royal

Royal STICK VAC PLUS Bedienungsanleitung

Royal

Royal Centrino SX3 Bedienungsanleitung

Royal

Royal Dirt Devil Vii Vac Bedienungsanleitung

Royal

Royal Handy ultra Bedienungsanleitung

Royal

Royal Procision RY3050 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Royal metal upright Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken