RS Mini Galaxy E 050-600 Bedienungsanleitung

Incubator

Model No: 050-600

User Manual

Issue E, January 2009

Contents

ContentsContents

Contents

Section Page No

1. Product Description 2

2. Guidance Notes and Routine Checks 3

3. Installation 4

4. Setting the Hu idity Conditions 7

5. Control Panel Description 8

6. Progra ing Te perature, CO2

& Auto Zeroing 9

7. Progra ing the Alar Syste 10

8. The Alar Syste 11

9. Syste Alar s 13

10. Cleaning and Disinfecting 14

11. Technical Specification 15

12. Ordering Infor ation 16

13. Accessories 18

If this incubator is fitted with Model Options, User Instructions and infor ation is located at the back,

after Ordering Infor ation.

Section 1

Section 1Section 1

Section 1

Product Description

The MiniGala y E CO

Incubator is designed to ensure accurate and reliable operation. The unit

incorporates a touch sensitive keypad and two, 3 digit L. E. D. displays which allows easy setting and

onitoring of the cha ber condition.

The icroprocessor control syste ensures a rapid, controlled return to opti u cha ber conditions

after a door opening whilst also preventing any overshoot.

A ther al heating ele ent co pletely surrounds the incubator providing an even te perature within

the cha ber. The independently heated outer door is designed to ensure an even distribution of heat

thereby eli inating condensation on the inner door.

Incorporated into the unit is an over te perature safety syste . This operates independently of the

ain control syste .

A purpose designed hu idity control syste allows a high unifor relative hu idity and prevents

undesirable condensation in other parts of the cha ber. The anual control syste allows li ited

adjust ent over an approxi ate range of 95 – 97% r/h.

A solid state infra red sensor is used to control the level of CO

giving excellent reliability and is

unaffected by hu idity. The CO

syste has a se i-auto atic zero function which provides a si ple

process for the user to follow to aintain the correct CO

level within the cha ber.

There is a two level alar syste . The cha ber onitoring alar is progra able and will alert you

if te perature or CO

have not recovered within a preset ti e after the door has been opened. If not

required, this syste can be disar ed. Syste alar s occur only if a fault has developed which

requires user intervention to rectify.

Air circulation is achieved without the use of a fan eli inating this potential source of conta ination

and reducing s all sa ple evaporation within the cha ber.

The 50 litre cha ber and all internal co ponents are anufactured fro polished stainless steel.

The shelf rack syste is designed for co plete re oval and easy access to the s ooth interior for

quick and thorough cleaning.

The outer shell of the incubator is anufactured fro zinc plated stove ena elled steel to give a

durable corrosion resistant finish.

The outer door and top cover are vacuu for ed fro ABS plastic and they provide a high level of

insulation. The keypad and display are incorporated into the top cover per itting axi u usable

cha ber volu e.

Section 2

Section 2Section 2

Section 2

Guidance Notes and Routine Checks

2.1 To ensure that cha ber conditions re ain as stable as possible always ini ize the length

of ti e that the inner door is open. The agnetic door catch is specifically designed to ake door

opening and closing as easy as possible. When opening the inner door, wipe off any s all drops of

condensate that ay have for ed on the inner seal. This will avoid a build up of condensation.

2.2 For cell culture work – we reco end the use of copper sulphate (or recognised biocide) in

the hu idity tray. Tests have shown that as well as inhibiting bacterial growth in the tray this

can reduce conta ination on the cha ber walls (one s all teaspoonful copper sulphate

reco ended).

2.3 For IVF and other sensitive work – we do not reco end the use of any biocide in the

hu idity tray. To reduce the possibility of conta ination, the hu idity tray water should be

changed and the hu idity tray cleaned with 70% Alcohol / 30% distilled water solution every

10 – 14 days. To re ove / replace the hu idity tray: - turn the tray through 45° and re ove

for refilling. To replace the hu idity tray, carefully turn through 45° and pass the tray through

the front of the shelf racks.

2.4

Daily

2.4.1 Check that the te perature and CO

levels are reading within specification.

2.4.2 Check the reserve pressure in the CO

cylinder (nor ally 50 bar when full). The design of

the incubator ensures very low consu ption of CO

and during nor al working conditions a type K

cylinder should last approxi ately 12 onths. If there is a significant drop at the cylinder 50 bar

pressure, it eans that the cylinder is al ost e pty and should be replaced, ensuring that there are

no leaks at any of the joints.

2.5

Monthly

2.5.1 If not changing the hu idity tray water / cleaning hu idity tray regularly - top up the hu idity

tray (to a axi u volu e of 0.5 litres). The use of war water (approx. 37.0°C) will ensure a rapid

return to opti u cha ber conditions. After topping-up, check that the hu idity tray is central

between the racks and pushed back against the stops.

Section 3

Section 3Section 3

Section 3

Installation

3.1 Unpack the incubator by lifting it fro the delivery pallet ensuring it is supported by the base.

At least two people are required for safe lifting. In the unlikely event of any transit da age this

ust be reported within 7 days.

3.2 The following ite s are supplied with your new incubator:-

3 Non-tip shelves (securely packed separately)

2 shelving racks (securely packed separately)

18 Silicone Rubber Suction Feet. Supplied packed in accessory bag

1 Hu idity tray (securely packed separately)

1 Mains power cord supplied packed in accessory bag

3 of PVC 6 bore plastic tubing supplied in accessory bag

1 CO

HEPA-vent filter (connected to PVC tube in accessory bag)

2 Hose clips supplied packed in accessory bag

4 Adjustable feet (To ensure adequate airflow for correct operation of the relative hu idity

control syste the incubator feet must be fitted. Feet are supplied fitted to the unit.

4 Anti-slip pads for the adjustable feet

1 Black sensor cover (in situ)

If required, further shelves can be purchased up to a axi u of 6. The hu idity tray has a fixed

position at the lowest shelf rack position. The hu idity tray should always be left in place even if the

incubator is not hu idified.

3.3 In order to use the incubator you will require:-

a) A 220/240V 50 Hz or 100/120V 50/60 Hz earthed electrical supply - ini u

capacity 3 a ps (5 a ps High Te perature Deconta ination Models).

A 100/120V 50/60 Hz earthed electrical supply - ini u capacity 6 a ps (8

a ps High Te perature Deconta ination Models).

b) CO

gas cylinder (100% CO

vapour withdrawal) together with a two

stage regulator for pressure control to 0.35 BAR. (5lbf / in

c) Copper Sulphate or other biocide for the hu idity reservoir (optional).

3.4 The incubator is designed to operate at a cha ber te perature of 4.0°C above a bient and

at an absolute ini u a bient te perature of 15°C if being used at 37°C. Therefore care

should be taken to avoid placing the incubator in draughts, direct sunlight or near a radiator.

The operating temperature range indicated above excludes any heat generating

equipment operating within the unit. The presence on any such appliance will affect the

operational temperature characteristics.

3.5 To ensure adequate airflow for correct operation of the relative hu idity control syste the

incubator feet must be fitted to insert the adjustable feet, front pair first, tilt the incubator

backwards, screw the feet in to the required depth. Repeat the operation, tilting the incubator

forward for the rear pair.

3.6 Place the incubator in the working position. The unit is designed to be sited on a level surface

capable of bearing 32kg (approx – actual weight will depend on options fitted). It is

reco ended that a spirit level be used on the centre of the iddle shelf to position the

incubator, the feet can be individually adjusted to co pensate for uneven surfaces. Fit the

anti-slip pads to the front feet. Purpose designed stands and stacking asse blies are also

available.

3.7 Asse ble the shelf racks as follows:- Carefully re ove any packaging. Fit 7 silicone rubber

suction cup feet to the shelf racks in positions indicated on the picture below left with an ‘*’.

Repeat for the opposite shelf rack.

To fit the shelf racks to the incubator:- The racks are ‘handed’ and the suction cup arked ‘R’

goes to the rear of the cha ber as shown in the centre picture above. The suction cups will

adhere to the cha ber walls dry, but can be da pened with distilled water to increase

adhesion if required. Ensure the shelf racks are fitted squarely to the cha ber to enable the

shelves to sit on a level plane (picture above right).

3.8 Connect the CO

using the 6 plastic tubing to the atching CO

inlet on the rear of the

incubator. Use the tubing clips provided to eli inate CO

leaks. Turn on the gas supply with

the pressure set to 0.35 BAR (5lbf/ in2). Re ove the black protective cover fro sensor

(keep for use when disinfecting). Ensure that the white porous sensor cover re ains in place.

WARNING!

levels.CO

is harmful in high concentrations. Any gases that may escape from the

unit have to be managed via adequate room ventilation or the use of an e haust system.

Check compliance with the ma imum permitted workplace concentration for CO

when

operating all units.

3.9 Connect the incubator to an earthed power supply using the power cord provided. The display

will illu inate i ediately. NB:- Do not progra e the CO

level yet

3.10 The cha ber set points are pre-progra ed at 37.0°C and 0% CO

. Leave the incubator

until the progra ed cha ber te perature has been reached.

3.11 Carefully unpack the hu idity tray. Fill with 0.5 litres of war distilled water (at approx.

37.0°C). For cell culture work – we reco end the use of copper sulphate (or recognised

biocide) in the hu idity tray (one s all teaspoonful copper sulphate reco ended).

For IVF and other sensitive work – we do not reco end the use of any biocide in the

hu idity tray. To reduce the possibility of conta ination, the hu idity tray water should be

changed and the hu idity tray cleaned with 70% Alcohol / 30% distilled water solution every

10 – 14 days. To re ove / replace the hu idity tray: - turn the tray through 45° and re ove

for refilling.. To fit the hu idity tray - Turn the hu idity tray through 45° and pull it forward as

shown in the pictures on the following page:-

NB – ensure that the Hu idity Tray is located centrally between the racks and pushed fully

back against the stop as shown above right.

3.13 Fit the shelves and leave the incubator for at least two hours (preferably overnight) to allow

conditions to stabilise.

3.14 Progra e the CO

level (i.e. 5%) and ensure that the CO

level stabilises at the

progra ed level

3.15 To carry out the Auto Zero, press the

‘∗’

and

‘↵’

keys si ultaneously. The Inner Door ust

be opened and closed according to the displayed instructions, after which the process is

co pletely auto atic.

3.16 The incubator is now ready for use.

Section 4

Section 4Section 4

Section 4

Setting the Humidity Conditions

If hu idification is required, the hu idity tray which is located on the lower shelf runners

should be pulled forward and filled with 0.5 litres of war distilled water for cell culture work –

we reco end the use of copper sulphate (or recognised biocide) in the hu idity tray. Tests

have shown that as well as inhibiting bacterial growth in the tray this can reduce

conta ination on the cha ber walls (one s all teaspoonful copper sulphate reco ended).

For IVF and other sensitive work – we do not reco end the use of any biocide in the

hu idity tray. To reduce the possibility of conta ination, the hu idity tray water should be

changed and the hu idity tray cleaned with 70% Alcohol / 30% distilled water solution every

10 – 14 days. To re ove / replace the hu idity tray: - turn the tray through 45° and re ove

for refilling.

DO NOT LEAVE WATER IN THE HUMIDITY TRAY IF THE INCUBATOR IS SWITCHED OFF , AS

THIS MAY RESULT IN DAMAGE TO THE CO

SENSOR.

Section 5

Section 5Section 5

Section 5

Control Panel escription

Control Panel escriptionControl Panel escription

Control Panel escription

The control panel consists of two, 3 seg ent LED displays, and 4 keys. The functions and

descriptions of these are described below.

∗

PROGRAMMING Key

PLUS Key

MINUS Key

‘↵’

ACCEPT Key

The deci al points on the display for Te perature and CO

flash ON / OFF to signify that the Alar

Syste is not ar ed.

The picture above shows the screen in nor al operation, this is how the screen should be illu inated

when running nor ally.

Section 6

Section 6Section 6

Section 6

Programming Temperature, CO

Programming Temperature, COProgramming Temperature, CO

Programming Temperature, CO

2 2

& Auto Zeroing

& Auto Zeroing& Auto Zeroing

& Auto Zeroing

6.1 Programming Temperature & CO

6.1 Programming Temperature & CO6.1 Programming Temperature & CO

6.1 Programming Temperature & CO

The

‘∗’

Key allows Te perature and CO

to be progra ed within the following ranges:

Te perature Range: 10°C ( ust be 1°C above a bient) to 50°C.

Range: 0.2% to 10%

Once the Te perature has been progra ed it ust be entered with the

‘↵’

Key, the CO

can then

be progra ed.

Press the

‘+

’ and

‘-’

keys si ultaneously to enter the Engineering Mode. If this is inadvertently done,

press the

‘∗’

key to exit.

6.2 CO

6.2 CO6.2 CO

6.2 CO

2 2

Auto Zero

Auto ZeroAuto Zero

Auto Zero

The purpose of the Auto Zero syste is to reference the CO

Sensor to an at ospheric CO

level of

0.05%. Over a period of ti e the sensor zero ay drift causing an inaccuracy in the CO

level at the

progra ed value. It is reco ended that the CO

syste is Auto Zeroed onthly to ensure that

level is correct.

To carry out the Auto Zero, press the

‘∗’

and

‘↵’

keys si ultaneously. The inner door ust be

opened and closed according to the displayed instructions, after which the process is co pletely

auto atic.

6.2.1 The door is opened for 60 seconds to co pletely degas the cha ber. A countdown is shown

on the display after which the instruction to close the door is displayed.

6.2.2 The door is then closed and a 10 inute countdown starts, to allow the cha ber conditions to

recover and the CO

sensor signal to stabilise, after which the sensor signal is auto atically re-

referenced. If the door is accidentally opened during the 10 inute countdown, close the door again to

reset the ti er and resu e the Auto Zero process until co plete.

6.2.3 The incubator will now re-open the CO

valve to allow the CO

level to recover to the

Progra e value.

6.2.4 Pressing the ‘

∗

’ key will auto atically ter inate the Auto Zero. Pressing any other key or

opening the door during the Auto Zero will not ter inate it.

Inhaltsverzeichnis

Andere RS Zubehör Handbücher

RS 7757517 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung