Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Q910 LTE

Access Point

Quick Setup Guide

Introduction

This Quick Setup Guide provides step-by-step instructions on

how to set up your Ruckus Q910 LTE Access Point (AP). After

completing the steps described in this guide, you will be able to

place the Q910 at your site and provide LTE wireless network

access to users.

Before You Begin

Before deploying the Ruckus Q910, verify that all items listed in

Package Contents are included in the package. If any item is

damaged or missing, notify your authorized Ruckus Wireless

sales representative. Also, make sure that you have the all the

hardware and tools mentioned in the Required Hardware and

Tools on page 1.

You can check for the latest information and release

documentation at

http://support.ruckuswireless.com/documents

Software License and Limited Warranty are available at

http://support.ruckuswireless.com/warranty

Required Hardware and Tools

•1/2” (13mm) at-blade screwdriver or equivalent

•No. 2 Phillips screw driver

•Small at-blade screwdriver

•Torque wrench or torque screwdriver with sockets

•Long-nose pliers

•Electrical wire stripping and terminal crimping pliers

•Pipe or pole--OR--a sturdy at surface

•Electric drill with drill bits and customer-supplied wall anchors,

at washers, and hex nuts for at-surface mount

•Four factory-supplied 1/2” (12.7mm) wide stainless steel

adjustable clamps, 2.5” (63.5mm) diameter, for mounting

bracket on smaller poles

•Ruler

Package Contents

A complete Q910 eld installation package includes all of the

items listed below (see Figure 1 for illustrations):

•Q910 LTE Access Point (A)

•Two M25 data cable glands (B)

•Outdoor AP Mounting Bracket Kit (C), consists of:

–Mounting bracket

–U-joint bracket

–Long (175mm) linkage bracket

–Short (100mm) linkage bracket

–AP bracket

–Four (4) hose clamps

–Packet of screws, washers, and other hardware

•Safety cable kit (D)

•One ground wire with lug (E)

•Service Level Agreement/Limited Warranty Statement

•Regulatory Statement

•This Quick Setup Guide

FIGURE 1 Package Contents

Mounting Instructions

The following section provides instructions for connecting,

attaching, and mounting the LTE Access Point.

Step 1: Connecting and Sealing the RJ45

Cables

The Q910 may use one or two RJ-45 cables, one for Ethernet and

Power (PoE IN), and another when the Q910 is optionally

supplying Ethernet out to a peripheral device, such as a small

camera or backhaul radio. Connect and seal the RJ-45 cables

using the M25 data cable glands as shown in Figure 3.

WARNING! Do not use any PoE Injector that is not tested and

approved by Ruckus Wireless to power the Q910 Access Point.

WARNING! Do not plug PoE IN power into the Ethernet OUT

port. See Figure 2.

WARNING! If using a PoE switch to supply power to the Q910,

30W MUST be reserved for the Q910 on the switch. Failure to

ensure a 30W supply may result in unpredictable operation of

the access point.

FIGURE 2 LEDs, PoE IN and Ethernet OUT Ports

1. Feed the end of the cable through the sealing nut, rubber O-

ring, clamping ring assembly and cable gland base as shown

in Figure 3.

FIGURE 3 RJ-45 Cable and Cable Gland Assembly

2. Connect the cable to the Ethernet port in the Q910.

3. Tighten the cable gland base into the Q910 chassis to 7 N.m

or 62 in-lbs.

4. Wrap the clamping ring assembly around the rubber O-ring.

Make sure that the clamping ring assembly fully encloses the

rubber O-ring.

5. Seat the clamping ring assembly and rubber O-ring in the

cable gland base.

6. Hand-tighten the sealing nut.

Published 09 July 2018, Part Number 800-71412-001 Rev A2

Step 2: Attaching the U-Joint bracket to the

Mounting Bracket

1. Position the U-joint bracket on the mounting bracket.

NOTE: Mount the U-joint bracket in any direction on the

mounting bracket, preferably to allow AP azimuth

adjustments. Then the AP bracket allows AP elevation

adjustments.

FIGURE 4 U-joint bracket attached horizontally to the

mounting bracket

2. Use four 1/4-28 bolt and washer sets (A) to mount the U-joint

bracket (B) to the mounting bracket (C). Tighten the bolts to

9.5 N.m (7 ft-lbs.)

3. Continue with Step 3A: Attaching the Mounting Bracket to a

Flat Surface on page 2 or Step 3B: Attaching the Mounting

Bracket to a Metal Pole on page 2.

Step 3A: Attaching the Mounting Bracket to a

Flat Surface

1. Place the mounting bracket at the location on the at surface

where you want to mount the AP. Use the holes on the

mounting bracket as a template to mark the locations of the

mounting holes.

FIGURE 5 Mounting bracket at surface holes

2. Remove the mounting bracket from the at surface.

3. Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall are

not included in the mounting kit.

4. Attach the mounting bracket to the at surface using the

mounting hardware.

5. Using the mounting hardware instructions, tighten the

hardware to secure the mounting bracket.

6. Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket on page 2.

Step 3B: Attaching the Mounting Bracket to a

Metal Pole

1. Insert the open end of one steel clamp into the upper two

slots on Insert the open end of one steel clamp into the

upper two slots on the mounting bracket.

2. Take the other steel clamp and insert it into the lower two

slots on the mounting bracket.

NOTE: The clamps can be daisy-chained together to

accommodate larger poles.

3. Use the clamps to attach the mounting bracket to the pole.

Tighten the clamps to 3 N.m or 27 in-lbs., or per

manufacturer’s specications.

FIGURE 6 Attaching the mounting bracket to a vertical

pole

4. Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket on page 2.

Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket

The linkage bracket attaches to the U-joint bracket using an M8

bolt and washer set. The linkage bracket is symmetrical, and

either end can be attached to the U-joint bracket.

NOTE: If you are mounting Q910 horizontally, use the longer

(175 mm) linkage bracket. If you are mounting Q910 vertically,

use the shorter (100 mm) linkage bracket.

FIGURE 7 Vertical mounting with Short Linkage Arm

Published 09 July 2018, Part Number 800-71412-001 Rev A2

FIGURE 8 Horizontal mounting with Long Linkage Arm

1. Loosely assemble the linkage bracket (A), the U-joint bracket

(C), one serrated external-tooth lock washer (B), and one M8

bolt and washer set (D).

FIGURE 9 Attaching the Linkage Bracket to the U-joint

Bracket

FIGURE 10 Additional orientation view of the

attachment of Linkage Bracket and U-joint Bracket to AP

bracket

2. Set the azimuth required by the AP.

3. Tighten the M8 bolt to 13.6 N.m (10 ft-lbs.)

4. Continue with Step 5: Attaching the AP Bracket to the

Linkage Bracket on page 3.

Step 5: Attaching the AP Bracket to the

Linkage Bracket

Attach the AP bracket to the linkage bracket using the included

bolt, nut, lock washer, at washer, serrated external-tooth

washer shown in Figure 10.

The AP bracket attaches to the linkage bracket using an M8 bolt

and washer set. The linkage bracket is symmetrical, and either

end can be attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its

serrated external-tooth lock washer on the inside of the AP

bracket anges. This ensures that the elevation adjustment

does not change.

As described in Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket on page 2, loosely assemble the AP bracket

(shown in Figure 10), the linkage bracket (A in Figure 9), the

second serrated external-tooth lock washer (B in Figure 9),

and the second M8 bolt and washer set (D in Figure 9).

Step 6: Attaching the AP Bracket to the

Access Point

1. Place the AP bracket on to the back side of the AP so that the

four larger screw holes on the bracket align with the four

screw holes on the AP. Make sure that the end of the AP

bracket with the hoisting loop is on the same side as the AP

PoE IN port.

FIGURE 11 Attaching the AP bracket to the AP

2. Use four 0.5-inch x 0.250-28 hex bolts with split lock and at

washer sets to mount the AP bracket to the AP. Tighten the

bolts to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION! Make sure that the screws are no longer than

0.5 inch. If a screw is longer than 0.5 inch, it can damage

the AP chassis.

3. If required, suspend the AP by attaching a carabiner to the

hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts, and

washers. You may use the extras wherever required.

4. Continue with Step 7: Setting the Elevation and Tightening

the Elevation Bolt on page 3.

Step 7: Setting the Elevation and Tightening

the Elevation Bolt

1. Set the elevation required by the AP.

2. Tighten the M8 bolt to13.6 N.m (10 ft-lbs.)

3. Continue with Step 8: Earth Grounding the AP on page 3.

Step 8: Earth Grounding the AP

CAUTION! Using the factory-supplied ground wire and ground

screw/washer set, connect a good earth ground to the AP

chassis ground point (Figure 12).

Published 09 July 2018, Part Number 800-71412-001 Rev A2

NOTE: The color coding of ground wires varies by region.

Before completing this step, check your local wiring standards

for guidance.

Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

ground point (Figure 12).

CAUTION! The Q910 AP includes one 12 mm stainless

steel M6x1 earth ground screw with split lock and at

washers. Make sure that any replacement screw is no

longer than 12 mm. If a screw is longer than 12 mm, it can

damage the AP chassis.

FIGURE 12 Connect good earth ground to AP here

Step 9: Installing the Security Cable

1. Thread the security cable through the mounting bracket (A)

and through the eye on the cable itself (B), as shown in

Figure 13.

2. Attach the safety cable to the AP (C) in Figure 13.

FIGURE 13 Attaching the Security Cable

Congratulations! You have mounted your Q910 access point.

Step 10: Checking the LED Lights

The LED lights verify the installation of AP

Once connected, AP will power on and automatically connect to

Ruckus Cloud over the Internet to congure itself. You will see

some activity and after 5-10 minutes all lights should turn solid

Green or solid Amber (LTE LED).

If any light is o or ashing, see the following table to help you

troubleshoot the issue.

Light Troubleshooting Action

PWR Check Power, Ethernet connections and PoE

(802.3at Type-2 (PoE+) Certied) switch.

EMS Check Internet connection and network/

rewall settings.

EPC Check Internet connection and network/

rewall settings.

SYNC Ensure at least one AP in the network is near

an unobstructed window for a good GPS

signal.

LTE For additional guidance, use the Ruckus Cloud

or contact Customer Support.

For more Information

The AP is now operational and can be further managed by the

Ruckus Cloud service. For more information, refer to the

appropriate Ruckus Wireless Cloud documentation or visit

http://support.ruckuswireless.com

Information

The Ruckus, Ruckus Wireless, Ruckus logo, and Big

Dog design trademarks are registered in the U.S. and

other countries. Other names and brands mentioned

in this document or website may be claimed as the

property of Ruckus or others.

Published 09 July 2018, Part Number 800-71412-001 Rev A2

Andere Handbücher für Q910

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless Unleashed H320 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310d Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T300 Installationsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex H500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless C500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7343 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZONEFLEX R310 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7321-U Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q710 LTE Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T305e Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless SmartZone 300 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung