Ruckus Wireless T310c Bedienungsanleitung

T310c Access Point

Quick Setup Guide

NOTE: The minimum software revision for the T310c is

ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 3.6 or

later, or standalone AP ﬁrmware 108.0 or later.

This Quick Setup Guide provides step-by-step instructions on

how to ﬁeld-install the Ruckus Wireless T310c access point

(AP). For detailed information on planning the installation,

performing a site survey, and operating the T310c, refer to the

Ruckus Wireless Outdoor Access Point User Guide

, available

at https://support.ruckuswireless.com.

WARNING! Only trained and qualiﬁed personnel should be

allowed to install, replace, or service this equipment.

WARNING! Installation of this equipment must comply with

local and national electrical codes.

CAUTION! Make sure that you form a 80mm - 130mm

(3”-5”) drip loop in any cable that is attached to the AP or

the building. This will prevent water from running along the

cable and entering the AP or the building where the cable

terminates.

CAUTION! Be sure that grounding is available and that it

meets local and national electrical codes. For additional

lightning protection, use lightning rods and lightning

arrestors.

CAUTION! Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING! Ruckus Wireless strongly recommends that you

wear eye protection before mounting the T310c.

This Guide in Other Languages

• 请从以下网站请得请指南的请体中文版 https://

support.ruckuswireless.com.

• Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

•このガイドの日本語版は https://

support.ruckuswireless.com でご覧ください。

•이가이드의 한국어 버전은 웹사이트 (https://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em https://

support.ruckuswireless.com.

• Puede ver la versión en español (América Latina) de esta

guía en https://support.ruckuswireless.com.

Before You Begin

Before deploying Ruckus Wireless products, please check for

the latest software and the release documentation.

• Release Notes and other user documentation are available

at http://support.ruckuswireless.com/documents.

• Software upgrades are available at http://

support.ruckuswireless.com/software.

• Open source information is available at http://

opensource.ruckuswireless.com.

• Software license and limited warranty information are

available at http://support.ruckuswireless.com/warranty.

Before deploying your Ruckus Wireless Access Point, verify

that all items listed in

Package Contents

are included in the

package. If any item is damaged or missing, notify your

authorized Ruckus Wireless sales representative. Also,

make sure that you have the required hardware and tools.

Required Hardware and Tools

• No. 2 Phillips screwdriver

• Small ﬂat-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole --OR-- a sturdy ﬂat surface

• Electric drill with drill bits and customer-supplied wall

anchors, ﬂat washers, and hex nuts for ﬂat-surface mount

Package Contents

A complete T310c ﬁeld installation package includes all of the

items listed below (see Figure below for illustrations):

• T310c Access Point (A)

• M25 data cable gland (B)

• Ground wire with lug (C)

• Pole/Wall Mount Bracket Kit (D)

• Four steel pipe clamps

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

FIGURE 1 T310c Package Contents

Mounting Instructions

Connecting And Sealing the RJ-45 Cables

Connect and seal the RJ-45 cable(s) using the M25 data

cable glands shown in the Figure below.

WARNING! Do not use any PoE injector not tested and

approved by Ruckus Wireless to power the T310c Access

Point.

FIGURE 2 T310c LEDs and Ports

1. Feed the end of the cable through the sealing nut, rubber

O-ring, clamping ring assembly and cable gland base as

shown.

NOTE: Do not seat the clamping ring and rubber O-ring

into the gland body until the gland body has been

torqued to spec.

Published September 2017, Part Number 800-71622-001 Rev A

FIGURE 3 RJ-45 cable and cable gland assembly

2. Use a wide ﬂat-blade screwdriver to remove the required

(PoE IN) blanking cap from the AP.

3. Connect the cable to the Ethernet port on the AP.

4. Tighten the cable gland base into the AP chassis to 7 N.m

or 62 in-lbs.

5. Wrap the clamping ring assembly around the rubber O-

ring. Make sure that the clamping ring assembly fully

encloses the rubber O-ring.

6. Seat the clamping ring assembly and rubber O-ring in the

cable gland base.

7. Hand-tighten the sealing nut.

Attaching the Mounting Bracket To A Flat

Surface

1. The AP mounting bracket attaches to the AP using a

captive screw. Use a medium ﬂat-blade or No. 2 Phillips

screwdriver to loosen the captive screw (A in the Figure

below) and pull up on the end of the bracket to remove

the bracket from the AP (B in the Figure below).

FIGURE 4 Removing the mounting bracket

2. Using either of the two options shown in Figure 5, hold

the mounting bracket at the location on the mounting

surface where you want to mount the AP. Use the holes

on the mounting bracket as a template to mark the

locations of the mounting holes.

NOTE: The mounting bracket can be mounted to a

vertical or horizontal surface to support the AP in the

required orientation.

FIGURE 5 Mounting bracket on a ﬂat surface

3. Remove the mounting bracket from the mounting surface.

4. Drill holes required for the customer-supplied mounting

hardware.

5. Attach the mounting bracket to the ﬂat surface using the

mounting hardware.

6. Using the mounting hardware instructions, tighten the

hardware to secure the mounting bracket.

7. Continue with Mounting the AP.

Attaching the Mounting Bracket to a Pole

1. The AP mounting bracket attaches to the AP using a

captive screw. Loosen the screw (A in Figure 4) and pull

up on the end of the bracket to remove the bracket from

the AP (B in the Figure above).

2. Insert the open end of one steel clamp (D in the Figure

above) into two of the slots on the mounting bracket.

NOTE: The mounting bracket can be mounted to a

vertical or horizontal pole to support the AP in the

required orientation.

3. Using either of the two options shown, use the clamp(s) to

attach the mounting bracket to the pole. Tighten the

clamps to 3 N.m or 27 in-lbs, or per manufacturer’s

speciﬁcations if the factory-supplied clamps are not used.

4. If necessary, daisy-chain the other steel clamps to

accommodate larger poles.

FIGURE 6 Mounting bracket on a pole

5. Continue with Mounting the AP.

Mounting the AP

1. Snap the AP back onto the mounting bracket (A in the

Figure below), and use a medium ﬂat-blade or No. 2

Phillips screwdriver to tighten the captive screw to 1.1

N.m or 10 in-lbs to secure the bracket to the AP (B).

FIGURE 7 Attaching the mounting bracket to the AP

2. Optional Step: If you also need to lock the mounting

bracket to the AP, then use a matching security

screwdriver to screw the customer-supplied locking

stainless steel 6mm M3 panhead security screw through

the mounting bracket and into the AP chassis.

CAUTION! Make sure that the customer-supplied

locking stainless steel M3 panhead security screw is no

longer than 6mm. If the security screw is longer than

6mm, it can damage the AP chassis.

Published September 2017, Part Number 800-71622-001 Rev A

FIGURE 8 Locking the mounting bracket to the AP

You have completed mounting the AP to the mounting

bracket.

Earth Grounding the AP

CAUTION! Make sure that earth grounding is available and

that it meets local and national electrical codes. For

additional lightning protection, use lightning rods and

lightning arrestors.

NOTE: The color coding of ground wires varies by region.

Before completing this step, check your local wiring

standards for guidance.

Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

ground point.

CAUTION! The T310c AP includes one 9mm stainless steel

M6x1 earth ground screw with split lock and ﬂat washers.

Make sure that any replacement screw is no longer than

9mm. If a screw is longer than 9mm, it can damage the AP

chassis.

FIGURE 9 Connect good earth ground to AP here

Congratulations! You have mounted your T310c access point.

Troubleshooting

CAUTION! If required, you can reset the AP to its factory

default settings by pressing the reset button located inside

the PoE IN port. DO NOT DO THIS UNLESS SO

INSTRUCTED. (Doing this resets the AP IP address to

192.168.0.1.)

NOTE: After a reset, you can access the internal AP web

interface using https://192.168.0.1. Your device must use

any other address from 192.168.0.2 through

192.168.0.254, with subnet mask 255.255.255.0. The

username is super, and the password is sp-admin. Refer to

the

Outdoor Access Point User Guide

for information on

conﬁguring and operating the AP. This document is

available at https://support.ruckuswireless.com.

For More Information

For information on how to conﬁgure and manage the AP, refer

to the

Ruckus Wireless Outdoor Access Point User Guide

available from https://support.ruckuswireless.com.

Published September 2017, Part Number 800-71622-001 Rev A

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless T610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7441 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed R310 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Installationsanleitung

Ruckus Wireless

Ruckus Wireless SC8800-S Installationsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7372 Einrichtungshandbuch

Ruckus Wireless

Ruckus Wireless ZF7761CM Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 802.11g Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless VF2811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R600 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R560 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R350 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed H510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless C500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung