Ruckus Wireless ZoneFlex 7372-E Bedienungsanleitung

Published June 2013, Part Number 800-70494-001 Rev B

ZoneFlex 7372-E 802.11n

Multimedia Wi-Fi Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on

how to set up your Ruckus Wireless ZoneFlex Access Point. After

completing the steps described in this Guide, you will be able to

place the Access Point (AP) at your site and provide wireless

network access to users.

THIS GUIDE IN OTHER LANGUAGES

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

請造訪以下網址，取得此手冊的繁體中文版本

https://support.ruckuswireless.com.

Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

このガイドの⽇本語版は https://support.ruckuswireless.com

でご覧ください。

이가이드의 한국어 버전은 웹사이트

(https://support.ruckuswireless.com)에서 확인하시기 바랍니다 .

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com.

BEFORE YOU BEGIN

Before deploying Ruckus Wireless products, please check for the

latest software and the release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents.

• Software Upgrades are available at

http://support.ruckuswireless.com/software.

• Open Source information is available at

http://opensource.ruckuswireless.com.

• Software License and Limited Warranty available at

http://support.ruckuswireless.com/warranty.

PACKAGE CONTENTS

• ZoneFlex 7372-E Access Point

• Mounting screws and anchors (2)

• Security screw (1)

• Regulatory flyer

• Declaration of Conformity (country-dependent)

• Product Warranty Statement

•ThisQuick Setup Guide

SETUP REQUIREMENTS

• A computer running Windows 7 (procedures for other OS’s

are similar)

• One or more of the following:

• A modem (DSL or cable), broadband router, or other

device provided by your Internet Service Provider that

brings Internet access to your site.

• A network switch or a DSL/Internet gateway device.

• Two Ethernet cables (Cat5e or better for PoE in)

• An AC power adapter (sold separately), or

• An 802.3af or 802.3at -compliant Power over Ethernet (PoE)

switch or PoE injector

STEP 1: CONNECT THE AP TO YOUR COMPUTER

1After removing your Ruckus Wireless AP from its package,

place it next to your computer.

2Using an Ethernet cable, connect your computer’s network

port to the 10/100/1000 port on the AP.

3Using the AC adapter (sold separately), connect the AP to a

convenient (and protected) power source.

• Alternatively, connect the 10/100/1000 port to a PoE

injector or PoE switch for both power and network con-

nectivity.

4Verify that the Power LED on the external enclosure is a

steady green.

STEP 2: PREPARE YOUR COMPUTER FOR AP

SETUP

1On your Windows 7 computer, configure your network

adapter from the Local Area Connection settings as follows:

•Start > Control Panel > Network and Sharing

Center > Change Adapter Settings

2Edit the TCP/IPv4 address settings as follows:

•Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties

The TCP/IPv4 Properties dialog box appears.

3Select Use the following IP address (if it is not already

selected) and then make the following entries:

•IP address: 192.168.0.22 (or any address in the

192.168.0.x network)

•Subnet mask: 255.255.255.0

•Default gateway: 192.168.0.1

Leave the DNS server fields empty.

4Click OK to save your changes.

Your changes are put into effect immediately.

NOTE: The ZoneFlex 7372-E requires a minimum of Zone-

Flex firmware version 9.6 and above to operate.

IMPORTANT!

If the AP is deployed with a ZoneDirector, follow the

ZoneDirector Quick Setup Guide, and connect the AP to your

local network.

NOTE:

The following procedures assume Windows 7 as the operating

system. Procedures for other OS’s are similar.

IMPORTANT!

Write down all of the currently active settings so you can

restore your computer to its current configuration later (when

this process is complete).

Published June 2013, Part Number 800-70494-001 Rev B

STEP 3: LOG INTO THE AP

As specified earlier, the AP should be directly connected to your

computer (through the Ethernet port) and powered on, ready for

setup.

1On your computer, open a Web browser window.

2In the browser, type this URL to connect to the AP:

https://192.168.0.1

3Press <Enter> to initiate the connection. When a security

alert dialog box appears, click OK/Yes to proceed.

4When the Ruckus Wireless Admin login page appears, enter

the following:

•Username: super

•Password: sp-admin

5Click Login.

STEP 4: CUSTOMIZE THE WIRELESS SETTINGS

1On the Web interface menu, click Configuration > Wire-

less (Configuration > Radio 2.4G or Configuration > Radio

5G). The Configure :: Wireless :: Common options appear.

2Verify that the following options are active:

•Channel: SmartSelect

•Country Code: If you are not located in the United

States, select your current country.

•External Antenna: Enable the check box and enter

the external antenna gain in the field provided.

3Click Update Settings if you made any changes.

4Click any of the eight “Wireless #” tabs at the top of the

page.

5In Wireless Availability, click Enabled.

6Delete the text in the SSID field, and then type a name for

your network that will help your users identify the AP in their

wireless network connection application.

7Click Update Settings to save your changes.

8Repeat Steps 4-7 for each Wireless # interface that you want

to enable.

9Click Logout to exit the Web interface.

10 Disconnect the AP from the computer and from the current

power source, and then restore your computer to its original

network connection configuration.

STEP 5: PLACE THE AP IN YOUR SITE

1Move the AP to its permanent location (accessible to both

AC power and network connection).

2Use an Ethernet cable to connect the 10/100/1000 port of

the AP to your network.

3Connect the AC power adapter (or PoE power supply) to the

AP, then to a convenient power source.

4Verify that the 10/100/1000 port LED is lit.

5Connect external antennas to the RP-SMA connectors on

the 7372-E enclosure. Note that each connector is a dual-

band (2.4 GHz & 5 GHz) spatial stream.

• Ruckus Wireless offers two different antenna kits as sep-

arately orderable accessories, certified for use with the

7372-E:

• 911-0303-VP02 (articulating direct-mount antenna

pair)

• 911-0505-DP01 (2-stream sector antenna panel)

After a short pause to re-establish the Internet connection, you

can test the AP.

STEP 6: VERIFY THE INSTALLATION

1Using any wireless-enabled computer or mobile device,

search for and select the wireless network you previously

configured.

2If you can connect, open a browser and link to any public

Web site.

Congratulations! Your wireless network is active and ready for

use.

Default AP Settings (For Your Reference)

Network Names

(SSIDs)

Wireless1—Wireless8 (2.4GHz radio)

Wireless9—Wireless16 (5GHz radio)

Security (Encryption

method)

Disabled for each wireless interface

Default Management

IP Address

192.168.0.1

NOTE:

If you will be using PoE, you will need a Cat5e (or better)

Ethernet cable to connect the AP to the PoE injector or switch.

Published June 2013, Part Number 800-70494-001 Rev B

(OPTIONAL) MOUNTING INSTRUCTIONS

The ZoneFlex 7372-E can be mounted to a wall, ceiling or to a T-

bar using the supplied mounting screws or the T-bar clips built

into the bottom of the AP enclosure.

Mounting to a Flat Surface

1Use this Quick Start Guide template or the alignment spacer

to mark the locations for screw holes on the mounting sur-

face. Use a 5mm drill bit to drill approximately 25mm into

the mounting surface.

2Insert the anchors and mounting screws into the mounting

surface, leaving approximately 0.28” (7 mm) of the screw

heads protruding for the AP enclosure.

The screws should be approximately 3.25” (82.6 mm) apart

per the template.

3Insert a straightened paperclip (or similar) into the hole on

the side of the AP (Figure 1.), to release the locking mecha-

nism.

Figure 1. Insert a paperclip into the pinhole

4Place the AP onto the mounting screws so that the screw

heads enter the mounting holes on the AP enclosure, and

push the AP downward to lock in place.

5Remove the paperclip to release the lock mechanism and

secure the AP.

6To unmount, insert a straightened paperclip into the hole on

the side of the AP to unlock, then push the AP upward to

release the AP enclosure from the mounting screws.

Mounting to a T-Bar

The ZoneFlex 7372-E provides mounting options for flush tile

and recessed frame T-bars in acoustical ceiling tiles.

Flush Tile

1Orient the AP so that the T-bar is positioned between the T-

bar clips as shown in Figure 2., then rotate the AP until the

third T-bar clip catches the T-bar and the latch locks the T-bar

in place (Figure 3.).

Figure 2.

Figure 3.

2For added security, insert the Torx-head security screw into

the security screw hole shown in Figure 3.

3To remove the unit, first remove the security screw, then

depress the latch while rotating the AP so that the T-bar clips

disengage the T-bar.

FOR MORE INFORMATION

You can now use the wireless network to log into the AP’s Web

interface. Use the Web interface to review and fine-tune a wide

range of AP settings. For information on how to configure the AP

from the Web interface, refer to the Ruckus Wireless ZoneFlex

Indoor Access Point User Guide or the Online Help, available

from within the Web interface.

Hold paperclip in

while mounting

Security screw

hole

Published June 2013, Part Number 800-70494-001 Rev B

Mounting template

Andere Handbücher für ZoneFlex 7372-E

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless Unleashed T610s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless SmartCell Gateway 200 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed T610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7351-U 802.11n Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R560 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R750 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7341 802.11n Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7372-E Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R600 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R320 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7343 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7441 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310c Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless H510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7962 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung