Ruckus Wireless T310n Bedienungsanleitung

T310n Access Point

Quick Setup Guide

NOTE: The minimum software revision for the T310n is

ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 3.6 or

later, or standalone AP ﬁrmware 108.0 or later.

This Quick Setup Guide provides step-by-step instructions on

how to ﬁeld-install the Ruckus Wireless T310n access point

(AP). For detailed information on planning the installation,

performing a site survey, and operating the T310n, refer to the

Ruckus Wireless Outdoor Access Point User Guide

, available

at https://support.ruckuswireless.com.

WARNING! Only trained and qualiﬁed personnel should be

allowed to install, replace, or service this equipment.

WARNING! Installation of this equipment must comply with

local and national electrical codes.

CAUTION! Make sure that you form a 80mm - 130mm

(3”-5”) drip loop in any cable that is attached to the AP or

the building. This will prevent water from running along the

cable and entering the AP or the building where the cable

terminates.

CAUTION! Be sure that grounding is available and that it

meets local and national electrical codes. For additional

lightning protection, use lightning rods and lightning

arrestors.

CAUTION! Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING! Ruckus Wireless strongly recommends that you

wear eye protection before mounting the T310n.

This Guide in Other Languages

• 请从以下网站请得请指南的请体中文版 https://

support.ruckuswireless.com.

• Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

•このガイドの日本語版は https://

support.ruckuswireless.com でご覧ください。

•이가이드의 한국어 버전은 웹사이트 (https://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em https://

support.ruckuswireless.com.

• Puede ver la versión en español (América Latina) de esta

guía en https://support.ruckuswireless.com.

Before You Begin

Before deploying Ruckus Wireless products, please check for

the latest software and the release documentation.

• Release Notes and other user documentation are available

at http://support.ruckuswireless.com/documents.

• Software upgrades are available at http://

support.ruckuswireless.com/software.

• Open source information is available at http://

opensource.ruckuswireless.com.

• Software license and limited warranty information are

available at http://support.ruckuswireless.com/warranty.

Before deploying your Ruckus Wireless Access Point, verify

that all items listed in

Package Contents

are included in the

package. If any item is damaged or missing, notify your

authorized Ruckus Wireless sales representative. Also,

make sure that you have the required hardware and tools.

Required Hardware and Tools

• No. 2 Phillips screwdriver

• Small ﬂat-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole --OR-- a sturdy ﬂat surface

• Electric drill with drill bits and customer-supplied wall

anchors, ﬂat washers, and hex nuts for ﬂat-surface mount

Package Contents

A complete T310n ﬁeld installation package includes all of the

items listed below (see Figure below for illustrations):

• T310n Access Point (A)

• M25 data cable gland (B)

• Ground wire with lug (C)

• Pole/Wall Mount Bracket Kit (D)

• Four steel pipe clamps

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

FIGURE 1 T310n Package Contents

T310n Sector Antenna Coverage

The T310n 30-Degree Narrow Sector AP is best deployed

where internal-antenna narrow beamwidths can provide

exceptional coverage to a narrow sector, or can support

extended reach in a point-to-point deployment. See the

following illustrations for typical internal-antenna coverage

patterns and high-density narrow-sector coverage pattern.

FIGURE 2 Typical AP narrow sector or point-to-point coverage

Published September 2017, Part Number 800-71623-001 Rev A

FIGURE 3 Typical AP high-density narrow-sector coverage

Mounting Instructions

Connecting And Sealing the RJ-45 Cables

Connect and seal the RJ-45 cable(s) using the M25 data

cable glands shown in the Figure below.

WARNING! Do not use any PoE injector not tested and

approved by Ruckus Wireless to power the T310n Access

Point.

FIGURE 4 T310n LEDs and Ports

1. Feed the end of the cable through the sealing nut, rubber

O-ring, clamping ring assembly and cable gland base as

shown.

NOTE: Do not seat the clamping ring and rubber O-ring

into the gland body until the gland body has been

torqued to spec.

FIGURE 5 RJ-45 cable and cable gland assembly

2. Use a wide ﬂat-blade screwdriver to remove the required

(PoE IN) blanking cap from the AP.

3. Connect the cable to the Ethernet port on the AP.

4. Tighten the cable gland base into the AP chassis to 7 N.m

or 62 in-lbs.

5. Wrap the clamping ring assembly around the rubber O-

ring. Make sure that the clamping ring assembly fully

encloses the rubber O-ring.

6. Seat the clamping ring assembly and rubber O-ring in the

cable gland base.

7. Hand-tighten the sealing nut.

Attaching the U-Joint Bracket to the Mounting

Bracket

1. Position the U-joint bracket on the mounting bracket.

NOTE: Mount the U-joint bracket in any direction on the

mounting bracket, preferably to allow AP azimuth

adjustments. Then the AP bracket allows AP elevation

adjustments.

FIGURE 6 U-joint bracket attached horizontally to the mounting bracket

2. Use four 1/4-28 bolt and washer sets (A) to mount the U-

joint bracket (B) to the mounting bracket (C). Tighten the

bolts to 9.5 N.m (7 ft-lbs).

3. Continue with

Attaching the Mounting Bracket to a Flat

Surface

Attaching the Mounting Bracket to a Pole

Attaching the Mounting Bracket to a Flat Surface

1. Place the mounting bracket at the location on the ﬂat

surface where you want to mount the AP. Use the holes

on the mounting bracket as a template to mark the

locations of the mounting holes.

FIGURE 7 Mounting bracket ﬂat surface holes

2. Remove the mounting bracket from the ﬂat surface.

3. Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall

are not included in the mounting kit.

4. Attach the mounting bracket to the ﬂat surface using the

mounting hardware.

5. Using the mounting hardware instructions, tighten the

hardware to secure the mounting bracket.

6. Continue with

Mounting the Linkage Bracket to the U-

Joint Bracket

Attaching the Mounting Bracket to a Pole

1. Insert the open end of one steel clamp into the upper two

slots on the mounting bracket.

2. Take the other steel clamp and insert it into the lower two

slots on the mounting bracket.

NOTE: The clamps can be daisy-chained together to

accommodate larger poles.

3. Use the clamps to attach the mounting bracket to the

pole. Tighten the clamps to 3 N.m or 27 in-lbs, or per

manufacturer’s speciﬁcations.

Published September 2017, Part Number 800-71623-001 Rev A

FIGURE 8 Attaching the mounting bracket to a vertical pole

4. Continue with

Mounting the Linkage Bracket to the U-

Joint Bracket

Mounting the Linkage Bracket to the U-Joint

Bracket

1. The linkage bracket attaches to the U-joint bracket using

an M8 bolt and washer set. The linkage bracket is

symmetrical, and either end can be attached to the U-joint

bracket.

NOTE: Make sure that linkage bracket is installed with

its serrated external-tooth lock washer on the inside of

the U-joint bracket ﬂanges. This ensures that the

azimuth adjustment does not change.

2. Loosely assemble the linkage bracket (A), the U-joint

bracket (C), one serrated external-tooth lock washer (B),

and one M8 bolt and washer set (D).

FIGURE 9 Attaching the linkage bracket to the U-joint bracket

3. Set the azimuth required by the AP.

4. Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

5. Continue with

Attaching the AP Bracket to the Linkage

Bracket

Attaching the AP Bracket to the Linkage Bracket

Attach the AP bracket to the linkage bracket using the

included bolt, nut, lock washer, ﬂat washer, serrated external-

tooth washer shown in the illustration below.

The AP bracket attaches to the linkage bracket using an M8

bolt and washer set. The linkage bracket is symmetrical, and

either end can be attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its

serrated external-tooth lock washer on the inside of the AP

bracket ﬂanges. This ensures that the elevation adjustment

does not change.

As described in

Mounting the Linkage Bracket to the U-

Joint Bracket

, loosely assemble the AP bracket to the

linkage bracket using the second serrated external-tooth

lock washer and the second M8 bolt and washer set.

FIGURE 10 Attach the linkage bracket to the AP bracket

Attaching the AP Bracket to the Access Point

1. Place the AP bracket onto the back side of the AP so that

the four larger screw holes on the bracket align with the

four screw holes on the AP. Make sure that the end of the

AP bracket with the hoisting loop is on the same side as

the AP PoE IN port.

FIGURE 11 Attaching the AP bracket to the AP

2. Use four 0.5-inch x 0.250-28 hex bolts with split lock and

ﬂat washer sets to mount the AP bracket to the AP.

Tighten the bolts to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION! Make sure that the screws are no longer

than 0.5 inch. If a screw is longer than 0.5 inch, it can

damage the AP chassis.

3. If required, suspend the AP by attaching a carabiner to

the hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts and

washers. You may use the extras where required.

4. Continue with

Set the Elevation and Tighten Elevation

Bolt

Set the Elevation and Tighten the Elevation Bolt

1. Set the elevation required by the AP.

2. Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

3. Continue with

Powering the AP with DC

Published September 2017, Part Number 800-71623-001 Rev A

Powering the AP with DC

The T310n can accommodate two sources of power – PoE

(48V) power and 12V DC.

The T310n can draw power from the Ethernet input as a class

3 device, providing a maximum of 12.95W to the system.

Alternately, power can be supplied through a customer-

provided 12V DC power supply (7-20V DC acceptable) that

will connect to a two pin terminal block. The terminal block is

accessible through a water-tight gland on one end of the unit.

The terminal block connection has surge and polarity

protection to protect against inserting the wrong polarity leads

into the terminal block.

NOTE: When both 12V DC and the 48V PoE power are

active, the T310n will prioritize the 12VDC power.

NOTE: If DC cables are individual wires, then a special

cable gland insert is required for IP67 seal.

1. Install the DC power supply as described in the DC power

supply accessory installation guide.

2. Connect the power cord to a DC power source.

3. Verify that the PWR LED is a steady green.

Earth Grounding the AP

CAUTION! Make sure that earth grounding is available and

that it meets local and national electrical codes. For

additional lightning protection, use lightning rods and

lightning arrestors.

NOTE: The color coding of ground wires varies by region.

Before completing this step, check your local wiring

standards for guidance.

Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

ground point.

CAUTION! The T310n AP includes one 9mm stainless steel

M6x1 earth ground screw with split lock and ﬂat washers.

Make sure that any replacement screw is no longer than

9mm. If a screw is longer than 9mm, it can damage the AP

chassis.

FIGURE 12 Connect good earth ground to AP here

Congratulations! You have mounted your T310n access point.

Installing a USB Dongle

To install a USB dongle (such as an IoT radio device such as

BLE, 802.15.4, Z-wave or similar), remove the two 3mm hex

screws, remove the cap, and insert the dongle into the USB

port.

Once installed, replace the cap and the hex screws, and

torque the screws to 7 in-lbs (0.79 N.m).

NOTE: If required, a larger USB dongle cap can be

purchased separately. The maximum dimensions of the

USB dongle that can be inserted (with the large USB

dongle cap, part # 902-0127-000) are 6 cm x 2 cm x 1.1

cm. Max Power: 450mW (SiLabs EM3578 max current

draw at +20 dBm is 80mA over a 3.3V rail).

FIGURE 13 Installing a USB dongle

Troubleshooting

CAUTION! If required, you can reset the AP to its factory

default settings by pressing the reset button located inside

the PoE IN port. DO NOT DO THIS UNLESS SO

INSTRUCTED. (Doing this resets the AP IP address to

192.168.0.1.)

NOTE: After a reset, you can access the internal AP web

interface using https://192.168.0.1. Your device must use

any other address from 192.168.0.2 through

192.168.0.254, with subnet mask 255.255.255.0. The

username is super, and the password is sp-admin. Refer to

the

Outdoor Access Point User Guide

for information on

conﬁguring and operating the AP. This document is

available at https://support.ruckuswireless.com.

For More Information

For information on how to conﬁgure and manage the AP, refer

to the

Ruckus Wireless Outdoor Access Point User Guide

available from https://support.ruckuswireless.com.

Published September 2017, Part Number 800-71623-001 Rev A

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless ZF2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T300 Installationsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed R600 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless MediaFlex 7811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless SmartZone 300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7372 Einrichtungshandbuch

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless zoneflex t301n Installationsanleitung

Ruckus Wireless

Ruckus Wireless T504 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless VF2811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed T610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless C500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310c Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed H510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R750 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung