Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Q910 LTE Access

Point

Quick Setup Guide

Introduction

This Quick Setup Guide provides step-by-step instructions on

how to set up your Ruckus Q910 LTE Access Point (AP). After

completing the steps described in this guide, you will be able to

place the Q910 at your site and provide LTE wireless network

access to users.

Before You Begin

Before deploying the Ruckus Q910, verify that all items listed in

Package Contents are included in the package. If any item is

damaged or missing, notify your authorized Ruckus Wireless

sales representative. Also, make sure that you have the all the

hardware and tools mentioned in the Required Hardware and

Tools on page 1.

You can check for the latest information and release

documentation at

http://support.ruckuswireless.com/documents

Software License and Limited Warranty are available at

http://support.ruckuswireless.com/warranty

Required Hardware and Tools

•1/2” (13mm) at-blade screwdriver or equivalent

•No. 2 Phillips screw driver

•Small at-blade screwdriver

•Torque wrench or torque screwdriver with sockets

•Long-nose pliers

•Electrical wire stripping and terminal crimping pliers

•Pipe or pole--OR--a sturdy at surface

•Electric drill with drill bits and customer-supplied wall anchors,

at washers, and hex nuts for at-surface mount

•Four factory-supplied 1/2” (12.7mm) wide stainless steel

adjustable clamps, 2.5” (63.5mm) diameter, for mounting

bracket on smaller poles

•Ruler

Package Contents

A complete Q910 eld installation package includes all of the

items listed below (see Figure 1 for illustrations):

•Q910 LTE Access Point (A)

•Two M25 data cable glands (B), packed in the Safety Cable kit

•Outdoor AP Mounting Bracket Kit (C), the box consists of:

–Mounting bracket

–U-joint bracket

–Long (175mm) linkage bracket

–Short (100mm) linkage bracket

–AP bracket (set of two pieces)

–Four (4) hose clamps

–Packet of screws, washers, and other hardware

•Safety Cable kit (D) and Quick Setup guide

•One ground wire with lug (E), packed in the Safety Cable kit

•Ruckus End User License Agreement/Limited Warranty

Statement

•Regulatory Statement

•This Quick Setup Guide

FIGURE 1 Package Contents

Mounting Instructions

The following section provides instructions for connecting,

attaching, and mounting the LTE Access Point.

Step 1: Connecting and Sealing the RJ45

Cables

The Q910 may use one or two RJ-45 cables, one for Ethernet and

Power (PoE IN), and another when the Q910 is optionally

supplying Ethernet out to a peripheral device, such as a small

camera or blackhaul radio. Connect and seal the RJ-45 cables

using the M25 data cable glands as shown in Figure 3.

WARNING! Do not use any PoE Injector that is not tested and

approved by Ruckus Wireless to power the Q910 Access Point.

WARNING! Do not plug PoE IN power into the Ethernet OUT

port. See Figure 2.

WARNING! If using a PoE switch to supply power to the Q910,

30W MUST be reserved for the Q910 on the switch. Failure to

ensure a 30W supply may result in unpredictable operation of

the access point.

FIGURE 2 LEDs, PoE IN and Ethernet OUT Ports

1. Feed the end of the cable through the sealing nut, rubber O-

ring, clamping ring assembly and cable gland base as shown

in Figure 3.

FIGURE 3 RJ-45 Cable and Cable Gland Assembly

2. Connect the cable to the Ethernet port in the Q910.

3. Tighten the cable gland base into the Q910 chassis to 7 N.m

or 62 in-lbs.

4. Wrap the clamping ring assembly around the rubber O-ring.

Make sure that the clamping ring assembly fully encloses the

rubber O-ring.

5. Seat the clamping ring assembly and rubber O-ring in the

cable gland base.

6. Hand-tighten the sealing nut.

Published December 2018, Part Number 800-71412-001 Rev B

Step 2: Attaching the U-Joint bracket to the

Mounting Bracket

1. Position the U-joint bracket on the mounting bracket.

NOTE: Mount the U-joint bracket in any direction on the

mounting bracket, preferably to allow AP azimuth

adjustments. Then the AP bracket allows AP elevation

adjustments.

FIGURE 4 U-joint bracket attached horizontally to the

mounting bracket

2. Use four 1/4-28 bolt and washer sets (A) to mount the U-joint

bracket (B) to the mounting bracket (C). Tighten the bolts to

9.5 N.m (7 ft-lbs.)

3. Continue with Step 3A: Attaching the Mounting Bracket to a

Flat Surface on page 2 or Step 3B: Attaching the Mounting

Bracket to a Metal Pole on page 2.

Step 3A: Attaching the Mounting Bracket to a

Flat Surface

1. Place the mounting bracket at the location on the at surface

where you want to mount the AP. Use the holes on the

mounting bracket as a template to mark the locations of the

mounting holes.

FIGURE 5 Mounting bracket at surface holes

2. Remove the mounting bracket from the at surface.

3. Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall are

not included in the mounting kit.

4. Attach the mounting bracket to the at surface using the

mounting hardware.

5. Using the mounting hardware instructions, tighten the

hardware to secure the mounting bracket.

6. Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket on page 2.

Step 3B: Attaching the Mounting Bracket to a

Metal Pole

1. Insert the open end of one steel clamp into the upper two

slots on Insert the open end of one steel clamp into the

upper two slots on the mounting bracket..

2. Take the other steel clamp and insert it into the lower two

slots on the mounting bracket.

NOTE: The clamps can be daisy-chained together to

accommodate larger poles.

3. Use the clamps to attach the mounting bracket to the pole.

Tighten the clamps to 3 N.m or 27 in-lbs., or per

manufacturer’s specications.

FIGURE 6 Attaching the mounting bracket to a vertical

pole

4. Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket on page 2.

Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket

The linkage bracket attaches to the U-joint bracket using an M8

bolt and washer set. The linkage bracket is symmetrical, and

either end can be attached to the U-joint bracket.

NOTE: If you are mounting Q910 horizontally, use the longer

(175 mm) linkage bracket. If you are mounting Q910 vertically,

use the shorter (100 mm) linkage bracket.

FIGURE 7 Vertical mounting with Short Linkage Arm

Published December 2018, Part Number 800-71412-001 Rev B

FIGURE 8 Horizontal mounting with Long Linkage Arm

1. Loosely assemble the linkage bracket (A), the U-joint bracket

(C), one serrated external-tooth lock washer (B), and one M8

bolt and washer set (D).

FIGURE 9 Attaching the Llnkage Bracket to the U-joint

Bracket

FIGURE 10 Additional Orientation view of the

attachment of Linkage Bracket to U-joint Bracket

2. Set the azimuth required by the AP.

3. Tighten the M8 bolt to 13.6 N-m (10 ft-lbs.)

4. Continue with Step 5: Attaching the AP Bracket to the

Linkage Bracket on page 3.

Step 5: Attaching the AP Bracket to the

Linkage Bracket

Attach the AP bracket to the linkage bracket using the included

bolt, nut, lock washer, at washer, serrated external-tooth

washer shown in Figure 10.

The AP bracket attaches to the linkage bracket using an M8 bolt

and washer set. The linkage bracket is symmetrical, and either

end can be attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its

serrated external-tooth lock washer on the inside of the AP

bracket anges. This ensures that the elevation adjustment

does not change.

As described in Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket on page 2, loosely assemble the AP bracket

(shown in Figure 10), the linkage bracket (A in Figure 9), the

second serrated external-tooth lock washer (B in Figure 9),

and the second M8 bolt and washer set (D in Figure 9).

Step 6: Attaching the AP Bracket to the

Access Point

1. Place the AP bracket on to the back side of the AP so that the

four larger screw holes on the bracket align with the four

screw holes on the AP. Make sure that the end of the AP

bracket with the hoisting loop is on the same side as the AP

PoE IN port.

FIGURE 11 Attaching the AP bracket to the AP

2. Use four 0.5-inch x 0.250-28 hex bolts with split lock and at

washer sets to mount the AP bracket to the AP. Tighten the

bolts to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION! Make sure that the screws are no longer than

0.5 inch. If a screw is longer than 0.5 inch, it can damage

the AP chassis.

3. If required, suspend the AP by attaching a carabiner to the

hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts, and

washers. You may use the extras wherever required.

4. Continue with Step 7: Setting the Elevation and Tightening

the Elevation Bolt on page 3.

Step 7: Setting the Elevation and Tightening

the Elevation Bolt

1. Set the elevation required by the AP.

2. Tighten the M8 bolt to13.6 N-m (10 ft-lbs.)

3. Continue with Step 8: Earth Grounding the AP on page 4.

Published December 2018, Part Number 800-71412-001 Rev B

Step 8: Earth Grounding the AP

CAUTION! Using the factory-supplied ground wire and ground

screw/washer set, connect a good earth ground to the AP

chassis ground point (Figure 12).

NOTE: The color coding of ground wires varies by region.

Before completing this step, check your local wiring standards

for guidance.

Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

ground point (Figure 12).

CAUTION! The Q910 AP includes one 12 mm stainless

steel M6x1 earth ground screw with split lock and at

washers. Make sure that any replacement screw is no

longer than 12 mm. If a screw is longer than 12 mm, it can

damage the AP chassis.

FIGURE 12 Connect good earth ground to AP here

Step 9: Installing the Security Cable

1. Thread the security cable through the mounting bracket (A)

and through the eye on the cable itself (B), as shown in

Figure 13.

2. Attach the safety cable to the AP (C) in Figure 13.

FIGURE 13 Attaching the Security Cable

Step 10: Checking the LED Lights

The LED lights verify the installation of AP

Once connected, AP will power on and automatically connect to

Ruckus Cloud over the Internet to congure itself. You will see

some activity and after 5-10 minutes all lights should turn solid

Green or solid Amber (LTE LED).

If any light is o or ashing, see the following table to help you

troubleshoot the issue.

Light Troubleshooting Action

PWR Check Power, Ethernet connections and PoE

(802.3at Type-2 (PoE+) Certied) switch.

EMS Check Internet connection and network/

rewall settings.

EPC Check Internet connection and network/

rewall settings.

SYNC Ensure at least one AP in the network is near

an unobstructed window for a good GPS

signal.

LTE For additional guidance, use the Ruckus Cloud

or contact Customer Support.

For more Information

The AP is now operational and can be further managed by the

Ruckus Cloud service. For more information, refer to the

appropriate Ruckus Wireless Cloud documentation or visit

http://support.ruckuswireless.com

ARRIS, the ARRIS logo, Ruckus, Ruckus Wireless, the Ruckus logo, and

the Big Dog design are trademarks of ARRIS International plc and/or

its aliates. All other trademarks are the property of their respective

owners.

Published December 2018, Part Number 800-71412-001 Rev B

Page 1

Ruckus Wireless, Inc. 350 West Java Drive Sunnyvale, CA 94089 USA

Q910 – LTE Access Point Ruckus Wireless Inc., an ARRIS Company

Federal Communications Commission Notices

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this

equipment.

For Class B Equipment:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different — Consult the dealer or an experienced radio/TV technician for help.

from that to which the receiver is connected.

This device meets all requirements specified in the FCC Part 96 Rules. This transmitter must not be co-located or operate in conjunction with any other

antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated

with minimum distance 20 cm between the radiator & your body.

Safety Notices and National Restrictions

This product is intended to be installed at a restricted access location and is marked with a visible warning that the surface may be hot

Professionally Installed Products

The product is to be installed according to the installation instructions. The User/Operator does not have access to the device once the device is

installed and in use. Provisions for permanent grounding are provided.

1. Installation personnel: This product is designed for a specific application and is to be installed by qualified personnel with knowledge of RF and

applicable rules. General users are not to attempt installation or changing settings.

2. Installation location: The product is to be installed at a location where the radiating antenna can be kept at least 20 cm from any nearby persons in

normal operation conditions to meet regulatory RF exposure requirement.

3. Installation procedure: Please refer to installation instructions for details.

4. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set forth in US CFR 47

Part 96. Violation of the rule could lead to serious federal penalty.

Products intended to be powered by an external power supply:

Warning –This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard EN 60950-

1). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits of the power supply

part number represent the country code. For additional applicable power supplies/options, see user instructions and product datasheet.

Medical Statement

Ruckus Wireless Access Points shall only be used in ME systems where the intended EM ENVIRONMENT does NOT rely on the Wireless radio link for

BASIC SAFETY or ESSENTIAL PERFORMANCE of the ME SYSTEM.

800-71413-001-B

Andere Handbücher für Q910

Inhaltsverzeichnis

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless T710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7351-U 802.11n Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782 Installationsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed T610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZF2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R350 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex H500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T300 Installationsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7441 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless E510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless MediaFlex 7811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless H320 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless VF2811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q710 LTE Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZF7762-AC Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless MediaFlex 7811 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung