Ruckus Wireless Unleashed R310 Bedienungsanleitung

Published September 2016, Part Number 800-71078-001 Rev B

UnleashedTM R310 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to set up

your Ruckus Wireless Unleashed R310 access point. After completing the

steps described in this Guide, the Unleashed Master Access Point

(Master AP) will be created. Additional Unleashed access points can be

added to the network for additional coverage and capacity.

BEFORE YOU BEGIN

Before deploying your Ruckus Wireless device, please check the Ruckus

Wireless Web site for the latest software and release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents

• Product Limited Warranty documents are available at

http://support.ruckuswireless.com/warranty

• Online Training Resources are available at

https://training.ruckuswireless.com

PACKAGE CONTENTS

• One Unleashed R310 access point

• Two mounting screws and plastic wall anchors

• One T8 5mm M2.5 Torx locking security screw

• One unit removal pin

• Regulatory flyer

• Product warranty statement

• Declaration of conformity, if required

•ThisQuick Setup Guide

CONFIGURING THE AP

•Step 1: Collecting Setup Requirements, Hardware, and Tools

•Step 2: Connect the AP to Power and Your Computer Network

•Step 3: Log In and Run the Setup Wizard

•Step 4: Customize Your Wireless LANs

•Step 5: Deploy Additional Unleashed Access Points

Figure 1. Unleashed R310 AP - top view

Step 1: Collecting Setup Requirements, Hardware,

and Tools

• A computer with Ethernet adapter running Windows 7 or equivalent,

with Firefox or equivalent web browser.

• One Cat 5e (or better) Ethernet cable.

• T8 Torx screwdriver.

• An AC-to-12VDC power adapter (sold separately)

--OR--

an 802.3af-compliant Power over Ethernet (PoE) switch or PoE

injector.

Step 2: Connect the AP to Power and Your

Computer Network

AAfter removing your Unleashed AP from its package, connect it to your

network switch or router using an Ethernet cable.

BConnect the AC power adapter (sold separately) to the 12VDC AP

port, and plug the AC power adapter into a convenient and protected

AC power source.

• Alternatively, connect the POE IN port to a PoE injector or PoE

switch for both power and network connectivity.

Figure 2. AP rear panel

CAfter bootup, verify that the PWR LED on the AP is a steady green.

Step 3: Log In and Run the Setup Wizard

AAs soon as the Unleashed AP is powered on and connected to the local

network, it boots up and begins broadcasting a temporary unencrypted

WLAN named “Configure.Me-[xxxxxx]” from the 2.4 GHz radio only.

BUsing your client’s WiFi configuration settings, select and associate to

the “Configure.Me-[xxxxxx]” WLAN.

Figure 3. Connect to the “ConfigureMe” WLAN

CLaunch a web browser and enter the following into the browser’s URL

bar: unleashed.ruckuswireless.com, and press Enter.

DSelect Create New Unleashed Network, and click Start to

begin.

Figure 4. Select “Create New Unleashed Network”

EThe “Configuring Unleashed Master” progress screen displays the

progress. Wait until the initialization process completes.

FOnce initialization is complete, ensure that you are still connected to

the “Configure.Me” WLAN, and click Next.

GYou will be redirected to the Setup Wizard. Complete the steps in the

Setup Wizard and click Finish.

Note: Do NOT disconnect the power or network cable from the

device during the setup process.

Published September 2016, Part Number 800-71078-001 Rev B

Figure 5. Complete the Setup Wizard to set up your Unleashed network

HOnce the Setup Wizard is finished, a “Configuring system settings and

rebooting” progress screen appears. Wait until the process is

complete.

Figure 6. Configuring system settings and rebooting

IConnect to the WLAN that you configured in the Setup Wizard, and

click OK to reconnect. You will be redirected to the

unleashed.ruckuswireless.com login screen.

JEnter your Admin Name and Password to login.

Figure 7. The Login page

KUpon successful login you will be presented with the Unleashed

Dashboard, which displays an overview of your Ruckus Unleashed

network.

Figure 8. : The Unleashed Dashboard

LThe first time you log in, you will be presented with a “Registration”

screen prompting you to register your Unleashed AP with Ruckus. This

step is optional, and you can choose to skip the registration and

Figure 9. Registration page

Step 4: Customize Your Wireless LANs

Once the Unleashed Master AP has been initialized, you can fine-tune the

settings of your first WLAN (that you created during the setup wizard), and

create any additional WLANs needed prior to attaching additional

Unleashed member APs. Then, when you deploy additional member APs in

whatever order you prefer, they will automatically retrieve all WLAN

configuration settings (and any other settings you have configured) from

the Unleashed Master AP.

AFrom the Dashboard, click anywhere in the WiFi Networks section to

expand the display of your deployed WLANs.

BOn the left side of the screen, select the WLAN box for the WLAN you

would like to configure, and click the Edit button to edit the

configuration; or click Create to create a new WLAN.

CIf you made any changes to the original WLAN, you will be

disconnected and will need to reconnect once the changes have been

deployed on the AP radios.

Congratulations! Your Unleashed network is now configured and ready for

use. You may now proceed to Step 5: Deploy Additional Unleashed

Access Points.

Step 5: Deploy Additional Unleashed Access Points

Deploying additional Unleashed member APs is simply a matter of

connecting them to the same Layer 2 network (subnet) and providing

power. They will discover the Unleashed Master and join automatically. No

additional steps are necessary.

For More Information

For more information on managing your Unleashed network, refer to the

Ruckus Wireless Unleashed Access Point Online Help, available from

https://support.ruckuswireless.com.

INSTALLING THE AP

The AP can be mounted on a flat surface, on a drop-ceiling T-bar, or on a

pole or flat surface. Refer to the following sections:

•Mounting on a Flat Surface

•Removing the AP from Flat-Surface Mounting Screws

•Mounting the AP on a Drop-Ceiling T-Bar

•Removing the AP from a Drop-Ceiling T-Bar

•Mounting the AP on a Flat Surface or Pole Using the Optional

Secure Mounting Bracket

•Removing the AP from the Optional Secure Mounting Bracket

Mounting on a Flat Surface

The factory-supplied mounting screws and plastic wall anchors allow you

to attach the AP to a wall or ceiling.

AUse the Mounting Template on the last page of this guide to mark the

locations for two drill holes on the mounting surface.

BUse a 4.75mm (3/16”) drill bit to drill holes approximately 25mm (1”)

deep into the mounting surface.

CInsert the factory-supplied anchors (A in Figure 10) and mounting

screws (B) into the mounting surface, leaving approximately 6 mm

(1/4”) of the screw heads protruding from the surface.

Figure 10. Mounting the AP on a flat surface

Published September 2016, Part Number 800-71078-001 Rev B

DPlace the AP onto the mounting screws so that the screw heads enter

the keyholes on the AP enclosure (C), and gently press down on the AP

until the locking tab in the upper AP keyhole locks the AP onto the top

mounting screw.

Removing the AP from Flat-Surface Mounting

Screws

ATo remove the AP from the factory-supplied mounting screws, gently

press the unit removal pin (A in Figure 11) into the access hole on the

end of the AP to release the bracket locking tab in the upper keyhole.

Figure 11. Removing the AP from the screw heads

BPush the AP up and pull it away from the mounting screw heads.

Mounting the AP on a Drop-Ceiling T-Bar

AOrient the AP so that the T-bar is positioned between the T-bar clips

as shown in Figure 12, then rotate the AP until the third T-bar clip

catches the T-bar and the latch locks the T-bar in place (Figure 13).

Figure 12. Initial position

Figure 13. Final position

B(OPTIONAL, for added security.) Using a Torx T8 screwdriver, insert the

locking screw (A) into the hole near the latch to lock the AP in place.

Removing the AP from a Drop-Ceiling T-Bar

• To remove the AP, first remove the security screw, then depress the

latch while rotating the AP so that the T-bar clips disengage the T-bar.

Mounting the AP on a Flat Surface or Pole Using the

Optional Secure Mounting Bracket

The customer-ordered Ruckus Wireless secure mounting bracket kit

(ordering part number 902-0120-0000) includes a metal mounting bracket

and provides greater security when attaching the AP to flat surfaces (walls

and ceilings) and to poles.

• If you are mounting the AP on a flat surface, then you will also need an

electric drill with a 4.75mm (3/16”) drill bit, and the four No. 6 zinc

plated screws and plastic wall anchors included with the kit.

• If you are mounting the AP on a truss or pole, then you will also need

the two customer-supplied stainless steel pipe clamps.

Continue with the following:

AIf you are mounting the AP on a flat surface, then use the secure

mounting bracket as a template to mark the locations for four drill

holes on the mounting surface. There are four screw holes available on

the secure mounting bracket.

Fasten the bracket to the flat surface using four mounting screws and

plastic wall anchors and continue with Step C.

BIf you are mounting the AP on a pipe or pole, then feed the two

customer-supplied stainless steel clamps through the slots on the

secure mounting bracket. Use common hand tools to tighten the

clamps around the pipe or pole.

After the bracket is attached, continue with Step C.

Figure 14. Attaching the AP to the secure mounting bracket

CInsert the two studs on the secure mounting bracket (A) into the

keyholes on the bottom of the AP.

DSlide the AP toward the Ethernet port until the locking tab in the upper

AP keyhole locks the AP onto the top mounting bracket stud.

Published September 2016, Part Number 800-71078-001 Rev B

Removing the AP from the Optional Secure

Mounting Bracket

AGently press the unit removal pin (A in Figure 15) into the access hole

on the end of the AP to release the bracket locking tab in the upper

keyhole.

Figure 15. Removing the AP from the secure mounting

bracket

BSlide the AP toward the unit removal pin and remove the AP from the

bracket.

TROUBLESHOOTING

• If required, you can reset the AP to its factory default settings by using

a straightened paper clip to press and hold the reset button located

between the POE IN and 12VDC ports, for six or more seconds.

CAUTION: DO NOT DO THIS UNLESS SO INSTRUCTED. (Doing this

resets the AP to its factory default settings.)

• Refer to the Ruckus Wireless Unleashed Access Point Online Help for

information on configuring and operating the AP. This document is

available at

https://support.ruckuswireless.com

Mounting Template:

82.6mm

3.25in

Inhaltsverzeichnis

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless E510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310c Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex H500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Installationsanleitung

Ruckus Wireless

Ruckus Wireless ZF7762-AC Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R750 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2925 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7942-OT Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q710 LTE Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless E510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless zoneflex t301s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T504 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless VF2811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZF7761CM Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless MediaFlex 7811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7351-U 802.11n Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless SC8800-S Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung