Ruckus Wireless Unleashed T610s Bedienungsanleitung

Published July 2017, Part Number 800-71452-001 Rev B Page 1 of 4

Unleashed T610s Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to

field-install the Ruckus Wireless Unleashed T610s access point (AP).

For detailed information on planning the installation, performing a site

survey, and operating the T610s, refer to the Unleashed Online Help,

available at https://docs.ruckuswireless.com/unleashed/200.4/

index.html.

WARNING: Only trained and qualified personnel should be allowed to

install, replace, or service this equipment.

WARNING: Installation of this equipment must comply with local and

national electrical codes.

CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip

loop in any cable that is attached to the AP or the building. This will

prevent water from running along the cable and entering the AP or the

building where the cable terminates.

CAUTION: Be sure that grounding is available and that it meets local

and national electrical codes. For additional lightning protection, use

lightning rods and lightning arrestors.

CAUTION: Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING: Ruckus Wireless strongly recommends that you wear eye

protection before mounting the T610s.

THIS GUIDE IN OTHER LANGUAGES

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

Vous trouverez la version française de ce guide à l'adresse suivante

https://support.ruckuswireless.com.

このガイドの⽇本語版は https://support.ruckuswireless.com

でご覧ください。

이가이드의 한국어 버전은 웹사이트

(https://support.ruckuswireless.com)에서 확인하시기 바랍니다 .

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com.

BEFORE YOU BEGIN

Before deploying your Ruckus Wireless Unleashed T610s, verify that

all items listed in Package Contents are included in the package. If any

item is damaged or missing, notify your authorized Ruckus Wireless

sales representative. Also, make sure that you have the required

hardware and tools.

REQUIRED HARDWARE AND TOOLS

• Customer-supplied outdoor-rated three-wire (1-2mm2or 14-

18AWG) AC cable

• 1/2” (13mm) flat-blade screwdriver or equivalent

• No. 2 Phillips screwdriver

• Small flat-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole --OR-- a sturdy flat surface

• Electric drill with drill bits and customer-supplied wall anchors, flat

washers, and hex nuts for flat-surface mount

• Four factory-supplied 1/2” (12.7mm) wide stainless steel

adjustable clamps, 2.5” (63.5mm) diameter, for main mounting

bracket on smaller poles

•Ruler

PACKAGE CONTENTS

A complete Unleashed T610s field installation package includes all of

the items listed below (see Figure 1for illustrations):

• Unleashed T610s Access Point (A)

• Two M25 data cable glands (B)

• Ground wire with lug (C)

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

Figure 1: Package Contents

NOTE: The outdoor AP Mounting Bracket and security cable are

optional accessories that must be purchased separately.

T610SSECTOR ANTENNA COVERAGE

The T610s 120-Degree Sector AP is best deployed where

internal-antenna beamforming can provide extended reach and

throughput to a 120-degree coverage area. See Figure 2 for the

azimuth coverage pattern, and see Figure 3 for the elevation

coverage pattern.

Figure 2: Typical AP sector azimuth plane coverage, top view

Figure 3: Typical AP sector elevation plane coverage, side view

Extended

120º Reach

Extended

30º Vertical

Beamwidth

10º - 20º Downtilt

Recommended for

Extended Coverage

Published July 2017, Part Number 800-71452-001 Rev B Page 2 of 4

CONFIGURING THE AP

If you will be installing the AP before configuring, then skip to Physical

Installation. If you will be configuring the AP first before physical

installation, then continue with this section.

Step 1: Configure Your Unleashed Network

Unleashed can be deployed using either a Mobile App, available for both iOS and Android,

or using your PC’s web browser. Refer to the relevant section depending on which method

you prefer to use:

•Step 2a: Setup Using the Unleashed Mobile App

•Step 2b: Setup Using a Web Browser

Step 2a: Setup Using the Unleashed Mobile App

To perform setup using the Unleashed Mobile App, download the iOS or Android app from

the app store.

AAs soon as the Unleashed AP is powered on and connected to the local network, it

boots up and begins broadcasting a temporary unencrypted WLAN named

“Configure.Me-[xxxxxx]” from both radios.

BUsing your client’s Wi-Fi connection settings, select and associate to the

“Configure.Me-[xxxxxx]” WLAN.

CLaunch the app, and follow the on-screen instructions to configure your Unleashed

network(s).

Figure 1. Unleashed Mobile App for iOS and Android

Figure 2. Configuring Unleashed from the Mobile App

Step 2b: Setup Using a Web Browser

AAs soon as the Unleashed AP is powered on and connected to the local network, it

boots up and begins broadcasting a temporary unencrypted WLAN named

“Configure.Me-[xxxxxx]” from both radios.

BUsing your client’s Wi-Fi connection settings, select and associate to the

“Configure.Me-[xxxxxx]” WLAN.

CLaunch a web browser and enter the following into the browser’s URL bar:

unleashed.ruckuswireless.com, and press Enter.

DYou will be redirected to the Setup Wizard. Complete the steps in the Setup Wizard

and click Finish.

Figure 3. Complete the Setup Wizard to set up your Unleashed network

EOnce the Setup Wizard is finished, a “Configuring system settings and rebooting”

progress screen appears. Wait until the process is complete.

FConnect to the WLAN that you configured in the Setup Wizard, and click OK to

reconnect. You will be redirected to the Unleashed login screen.

GEnter your Admin Name and Password to login.

Figure 4. The Login page

HUpon successful login you will be presented with the Unleashed Dashboard, which

displays an overview of your Ruckus Unleashed network.

Figure 5. The Unleashed Dashboard

IClick OK to save your changes.

Your changes are put into effect immediately. Continue with Step 3: Customize Your

Wireless LANs.

STEP 3: CUSTOMIZE YOUR WIRELESS LANS

Once the Unleashed Master AP has been initialized, you can fine-tune the settings of your

first WLAN (that you created during the setup wizard), and create any additional WLANs

needed prior to attaching additional Unleashed member APs. Then, when you deploy

additional member APs in whatever order you prefer, they will automatically retrieve all

WLAN configuration settings (and any other settings you have configured) from the

Unleashed Master AP.

1From the Dashboard, click anywhere in the WiFi Networks section to expand the

display of your deployed WLANs.

2On the left side of the screen, select the WLAN box for the WLAN you would like to

configure, and click the Edit button to edit the configuration; or click Create to create

a new WLAN.

3If you made any changes to the original WLAN, you will be disconnected and will need

to reconnect once the changes have been deployed on the AP radios.

Congratulations! Your Unleashed network is now configured and ready for use. You may

now proceed to Step 4: Deploy Additional Unleashed Access Points.

STEP 4: DEPLOY ADDITIONAL UNLEASHED ACCESS

POINTS

Deploying additional Unleashed member APs is simply a matter of connecting them to the

same Layer 2 network (subnet) and providing power. They will discover the Unleashed

Master and join automatically. No additional steps are necessary.

Published July 2017, Part Number 800-71452-001 Rev B Page 3 of 4

PHYSICAL INSTALLATION

STEP 1: CONNECTING AND SEALING THE RJ-45

CABLES

Connect and seal the RJ-45 cable(s) using the M25 data cable gland

as shown in Figure 5.

WARNING: Do not use any PoE injector not tested and approved by

Ruckus Wireless to power the T610s Access Point.

WARNING: Do NOT plug PoE in power into the non-PoE Port (see

Figure 4).

Figure 4: T610s bottom view

1Feed the end of the cable through the sealing nut, rubber O-ring,

clamping ring assembly and cable gland base as shown in Figure

Figure 5: RJ-45 cable and cable gland assembly

2Use a wide flat-blade screwdriver to remove the required (PoE IN)

blanking cap from the T610s.

3Connect the cable to the Ethernet port on the T610s.

4Tighten the cable gland base into the T610s chassis to 7 N.m or

62 in-lbs.

5Wrap the clamping ring assembly around the rubber O-ring. Make

sure that the clamping ring assembly fully encloses the rubber O-

ring.

6Seat the clamping ring assembly and rubber O-ring in the cable

gland base.

7Hand-tighten the sealing nut.

STEP 2: ATTACHING THE U-JOINT BRACKET TO THE

MOUNTING BRACKET

NOTE: The following mounting instructions require purchase of

optional accessories that are not included in the standard T610s

package. The outdoor AP Mounting Bracket and safety cable are

optional accessories that must be purchased separately.

1Position the U-joint bracket on the mounting bracket.

Figure 6: U-joint bracket attached horizontally to the mounting bracket

NOTE: Mount the U-joint bracket in any direction on the mounting

bracket, preferably to allow AP azimuth adjustments. Then the AP

bracket allows AP elevation adjustments.

2Use four 1/4-28 bolt and washer sets (A) to mount the U-joint

bracket (B) to the mounting bracket (C). Tighten the bolts to 9.5

N.m (7 ft-lbs).

3Continue with Step 3a: Attaching the Mounting Bracket to a

Flat Surface or Step 3b: Attaching the Mounting Bracket to a

Metal Pole.

STEP 3A: ATTACHING THE MOUNTING BRACKET TO A

FLAT SURFACE

1Place the mounting bracket at the location on the flat surface

where you want to mount the AP. Use the holes on the mounting

bracket as a template to mark the locations of the mounting

holes.

Figure 7: Mounting bracket flat surface holes

2Remove the mounting bracket from the flat surface.

3Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall are not included

in the mounting kit.

4Attach the mounting bracket to the flat surface using the

mounting hardware.

5Using the mounting hardware instructions, tighten the hardware to

secure the mounting bracket.

6Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

STEP 3B: ATTACHING THE MOUNTING BRACKET TO A

METAL POLE

1Insert the open end of one steel clamp into the upper two slots on

the mounting bracket.

2Take the other steel clamp and insert it into the lower two slots on

the mounting bracket.

NOTE: The clamps can be daisy-chained together to accommodate

larger poles.

3Use the clamps to attach the mounting bracket to the pole.

Tighten the clamps to 3 N.m or 27 in-lbs, or per manufacturer’s

specifications.

Figure 8: Attaching the mounting bracket to a vertical pole

4Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

STEP 4: MOUNTING THE LINKAGE BRACKET TO THE

U-JOINT BRACKET

The linkage bracket attaches to the U-joint bracket using an M8 bolt

and washer set. The linkage bracket is symmetrical, and either end

can be attached to the U-joint bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the U-joint bracket

flanges. This ensures that the azimuth adjustment does not

change.

1Loosely assemble the linkage bracket (A), the U-joint bracket (C),

one serrated external-tooth lock washer (B), and one M8 bolt

and washer set (D).

Cable gland base

Clamping ring assembly

Rubber O-ring

Sealing nut

Published July 2017, Part Number 800-71452-001 Rev B Page 4 of 4

Figure 9: Attaching the linkage bracket to the U-joint bracket

2Set the azimuth required by the AP.

3Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

4Continue with Step 5: Attach the AP bracket to the linkage

bracket.

STEP 5: ATTACH THE AP BRACKET TO THE LINKAGE

BRACKET

Attach the AP bracket to the linkage bracket using the included bolt,

nut, lock washer, flat washer, serrated external-tooth washer shown in

Figure 10.

The AP bracket attaches to the linkage bracket using an M8 bolt and

washer set. The linkage bracket is symmetrical, and either end can be

attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the AP bracket flanges.

This ensures that the elevation adjustment does not change.

1As described in Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket, loosely assemble the AP bracket (shown in

Figure 11), the linkage bracket (A in Figure 9), the second

serrated external-tooth lock washer (B in Figure 9), and the

second M8 bolt and washer set (D in Figure 9).

Figure 10: Attach the linkage bracket to the AP bracket

STEP 6: ATTACHING THE AP BRACKET TO THE

ACCESS POINT

1Place the AP bracket onto the back side of the AP so that the four

larger screw holes on the bracket align with the four screw holes

on the AP. Make sure that the end of the AP bracket with the

hoisting loop is on the same side as the AP PoE IN port.

Figure 11: Attaching the AP bracket to the AP

2Use four 0.5-inch x 0.250-28 hex bolts with split lock and flat

washer sets to mount the AP bracket to the AP. Tighten the bolts

to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION: Make sure that the screws are no longer than 0.5 inch.

If a screw is longer than 0.5 inch, it can damage the AP chassis.

3If required, suspend the AP by attaching a carabiner to the

hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts and washers. You

may use the extras wherever required.

STEP 7: SET THE ELEVATION AND TIGHTEN ELEVA-

TION BOLT

1Set the elevation required by the AP.

2Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

STEP 8: EARTH GROUNDING THE AP

CAUTION: Make sure that earth grounding is available and that it

meets local and national electrical codes. For additional lightning

protection, use lightning rods and lightning arrestors.

NOTE: The color coding of ground wires varies by region. Before

completing this step, check your local wiring standards for

guidance.

• Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

ground point (Figure 12).

CAUTION: The T610s AP includes one 12mm stainless steel

M6x1 earth ground screw with split lock and flat washers. Make

sure that any replacement screw is no longer than 12mm. If a

screw is longer than 12mm, it can damage the AP chassis.

Figure 12: Connect good earth ground to AP here

STEP 9: INSTALLING THE SECURITY CABLE

NOTE: The security cable is an optional accessory that must be

purchased separately.

1Thread the security cable through the mounting bracket (A) and

through the eye on the cable itself (B), as shown in Figure 13.

2Attach the safety cable to the AP (C) in Figure 13.

Figure 13: Attaching the security cable

Congratulations! You have mounted your T610s access point.

INSTALLING AUSB DONGLE

To install a USB dongle, which could be an IoT radio like BLE,

802.15.4, Z-wave or the like, remove the two 3mm hex screws,

remove the cap, and insert the dongle into the USB port. Once

installed, replace the cap and the hex screws, and torque the screws

to 7 in-lbs.

Figure 14: Installing a USB dongle

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless E510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed R310 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T811-CM Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZF7761CM Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless zoneflex t301s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782 Installationsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7025 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R720 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless E510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex H500 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7343 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Q910 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T710 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless VF2811 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782-E Installationsanleitung

Ruckus Wireless

Ruckus Wireless T750 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless MediaFlex 7811 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung