Ruijie RG-PF2920U-4GT1MS-P Series Installations- und Betriebsanleitung

RG-PF2920U-4GT1MS-P

Series Switch

Hardware Installation and Reference Guide

Document version: V1.4

Date: 2023-11-13

All rights are reserved in this document and this statement.

Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document

or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks

is prohibited.

Trademark and are owned by Ruijie Networks.

All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.

Disclaimer

The products, services, or features you purchase are subject to commercial contracts and terms, and some or

all of the products, services, or features described in this document may not be available for you to purchase or

use. Except for the agreement in the contract, Ruijie Networks makes no explicit or implicit statements or

warranties with respect to the content of this document.

Due to product version upgrades or other reasons, the content of this document will be updated from time to

time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.

This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder

any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Intended Audience

This document is intended for:

Network engineers

Technical support and servicing engineers

Network administrators

Technical Support

Ruijie Networks website: https://www.ruijienetworks.com/

Technical support website: https://ruijienetworks.com/support

Case portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical support email: [email protected]

Live chat: https://www.ruijienetworks.com/rita

Conventions

1. Signs

The signs used in this document are described as follows:

Warning

An alert that calls attention to important rules and information that if not understood or followed can result in

data loss or equipment damage.

Caution

An alert that calls attention to essential information that if not understood or followed can result in function

failure or performance degradation.

Note

An alert that contains additional or supplementary information that if not understood or followed will not lead to

serious consequences.

Specification

An alert that contains a description of product or version support.

2. Note

The manual offers configuration information (including model, port type and command line interface) for

indicative purpose only. In case of any discrepancy or inconsistency between the manual and the actual version,

the actual version prevails.

Hardware Installation and Reference Guide

1 Product Description

The RG-PF2920U-4GT1MS-P is the simplified optical Ethernet (SOE) switch released by Ruijie Networks for

all-optical network scenarios.

It can be used with the Power over Fiber (PoF) switch to realize remote power supply, dual-network deployment,

energy saving, and flexible installation. It is also designed with a built-in PD power supply, which is stable and

reliable and suitable for indoor scenarios.

With Ruijie's modular OS, the RG-PF2920U-4GT1MS-P is fit for the SOE solution, and implements lifecycle

management, security control, plug and play, and intelligent O&M through software-defined networking (SDN).

Table 1-1 Ports of the RG-PF2920U-4GT1MS-P

Model

10M/100M/1000M

Base-T Ethernet

Electrical Port

2.5G SFP Port

Console Port

RG-PF2920U-4GT1MS-P

Note

2.5G SFP ports are downward compatible with 1000Base-X ports.

1000Base-T ports are downward compatible with 100Base-T and 10Base-T ports.

Table 1-2 Technical Specifications of the RG-PF2920U-4GT1MS-P

Model

PoE-

capable

Port

Maximum

PoE

Power

Per Port

Overall

Available

PoE

Power

Dimensions (W x

D x H)

Cooling

RG-PF2920U-4GT1MS-P

Ports 1–4

30 W

60 W

200 mm x 170 mm

x 55 mm (7.87 in. x

6.69 in. x 2.17 in.)

Natural

heat

dissipation

for fanless

design

1.1 RG-PF2920U-4GT1MS-P

Table 1-3 Technical Specifications

Model

RG-PF2920U-4GT1MS-P

CPU

Built-in CPU, single-core processor, and clock speed of 400 MHz

Hardware Installation and Reference Guide

BootROM

N/A

Flash Memory

128 MB

SDRAM

256 KB

Supported Optical

Module

See Appendix B.

The supported optical module types may update without prior notification. Please

contact Ruijie Networks for any updates.

SFP Port

2500Base-X and 1000Base-X

Power Supply

Rated voltage range: 44 V DC to 57 V DC

Rated current: 1.7 A

Maximum Ground

Leakage Current

3.5 mA

Energy Efficient

Ethernet (EEE)

Supported

PoE

Ethernet electrical ports 1–4 support PoE.

Maximum overall PoE output power ≥ 60 W

The maximum number of PoE devices supported by the switch is determined by

the PoE output power of the switch and the actual power of the PoE devices.

Maximum Power

Consumption

Without PoE load: 15 W

With PoE load: 75 W

Operating

Temperature

Rack deployment: 0ºC to 45ºC (32°F to 113°F) at the altitude between 0 m to

1,800 m (0 ft. to 5905.51 ft.)

Desktop or ELV box deployment: 0ºC to 40ºC (32°F to 104°F) at the altitude

between 0 m to 1,800 m (0 ft. to 5905.51 ft.)

At the altitude between 1,800 m (5905.51 ft.) and 5,000 m (16404.2 ft.), every

time the altitude increases by 220 m (721.79 ft.), the maximum temperature

decreases by 1°C (1.8°F).

Storage

Temperature

–40°C to +70°C (–40°F to +158°F)

Operating Humidity

10% to 90% RH (non-condensing)

Storage Humidity

5% to 95% RH (non-condensing)

Fan Module

Natural heat dissipation for fanless design

Intelligent

Temperature

Control

Temperature alarm and overheat protection

EMC Standard

GB/T 9254.1

Hardware Installation and Reference Guide

Safety Standard

GB 4943.1

Dimensions (W x D

x H)

200 mm x 170 mm x 55 mm (7.87 in. x 6.69 in. x 2.17 in.)

Weight

2.07 kg (4.56 lbs) (including the package)

Warning

In a domestic environment, this product may cause radio interference in which case the user may be required

to take adequate measures.

1.1.1 Product Appearance

The RG-PF2920U-4GT1MS-P provides 4 ×10/100/1000M Base-T Ethernet electrical ports, 1 x 2.5G SFP port,

and 1 x console port on the front panel, and the AC power input port on the side panel.

Figure 1-2 Appearance of the RG-PF2920U-4GT1MS-P

Hardware Installation and Reference Guide

1. Front Panel

Figure 1-3 Front Panel of the RG-PF2920U-4GT1MS-P

Note:

1. System status LED

2. PoE LED

3. Mode button

4. Type-C connector (5 V power supply

only)

5. Console port

6. Optical port LED

7. 1G/2.5GBase-X optical port

8. 10/100/1000Base-T Ethernet port with auto-

negotiation

9. Ethernet port LED

Caution

You can press the mode button to switch the port status indicator function (switch mode or PoE mode). Hold down the

button for more than 2s to ensure successful switching.

Hardware Installation and Reference Guide

2. Side Panel

Figure 1-4 Side Panel of the RG-PF2920U-4GT1MS-P

Note:

1. Grounding stud

2. Power port

1.2 Power Supply

Rated values of the RG-PF2920U-4GT1MS-P:

Rated voltage range: 44 V DC to 57 V DC

Rated current: 1.7 A

1.3 LEDs

LED

Panel

Identification

Status

Description

Status LED

Status

Off

The switch is not powered on.

Blinking

green

The switch is being initialized. If the LED blinks

continuously, a fault occurs.

Solid

green

The switch works properly.

Solid

yellow

A switch temperature alarm is generated. Check

the operating environment of the switch.

Hardware Installation and Reference Guide

Solid red

The temperature exceeds the threshold,

causing the system to restart.

PoE LED

PoE

Solid

green

The LED shows the switching status (switch

mode).

Solid

yellow

The LED shows the PoE status (PoE mode).

Electrical port LED

(switch mode)

1–4

Off

The port is not connected.

Solid

green

The port works at the rate of 10/100/1000 Mbps.

Blinking

green

The port is sending or receiving data at the rate

of 10/100/1000 Mbps.

Electrical port LED

(PoE mode)

1–4

Off

PoE of the port is disabled.

Solid

green

PoE of the port is enabled.

Blinking

green

PoE of the port is overloaded or the port is

faulty.

Optical port LED

Off

The port is not connected.

Solid

green

The port is connected at the rate of 1 Gbps or

2.5 Gbps.

Blinking

green

The port is sending or receiving data at the rate

of 1 Gbps or 2.5 Gbps.

Solid red

An error occurs when the optical module sends

signals.

Solid

yellow

An error occurs when the optical module

receives signals.

1.4 Heat Dissipation

The RG-PF2920U-4GT1MS-P adopts natural heat dissipation to ensure that it works properly in a specified

environment. Dust the device every three months to avoid blocking ventilation openings on the housing.

Hardware Installation and Reference Guide

2 Preparing for Installation

2.1 Safety Precautions

Warning

To avoid personal injury and device damage, carefully read the safety precautions before you install the

RG-PF2920U-4GT1MS-P.

The following safety precautions may not cover all possible dangers.

2.1.1 Mounting

Keep the chassis clean and dust-free.

Do not place the device in a walking area.

During installation and maintenance, do not wear loose clothes, ornaments, or any other things that may be

hooked by the chassis.

Cut off all the power supplies and unplug all power cords before handling the switch.

2.1.2 Handling

Avoid handling the device frequently.

Keep balance and prevent personal injuries when handling the device.

Cut off all the power supplies and unplug all power cords before moving or handling the switch. Avoid scalds

because the housing surface is hot.

2.1.3 Electricity

Observe local regulations and specifications during electric operations. Only qualified personnel can perform

such operations.

Before installing the device, check whether there are hidden risks in the operating environment of the device.

For example, check whether the power socket is grounded and whether the ground is wet.

Determine the location of the indoor emergency power supply switch before installing the device. When an

accident occurs, immediately cut off all power supplies.

Do not maintain the device by yourself when the device is powered on.

Make sure that the device is powered off when you cut off the power supply.

Do not place the device in a wet position, and keep the device away from liquid.

Warning

Improper or incorrect electric operations may cause a fire, electric shock, and other accidents, and lead

to severe and fatal personal injury and device damage.

Direct or indirect contact through wet objects with high voltage or mains power supply may be fatal.

If a power supply system is equipped with a leakage protector (also referred to as leakage current switch

or breaker), the rated leakage action current of each leakage protector must be twice greater than the

maximum leakage current of all the power supplies in the system. For example, if the system is equipped

with 16 identical power modules and the leakage current of each power module is equal to or less than

Inhaltsverzeichnis

Andere Ruijie Schalten Handbücher

Ruijie

Ruijie RG-IS2712G Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2600G-I Series Bedienungsanleitung

Ruijie

Ruijie RG-ES126S-P Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-IF2920U-12GT1XS-DC Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NIS3100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6000C-48GT4XS-E Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES05 Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-NBS5100-24GT4SFP-P Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6580-24DC8QC Installations- und Betriebsanleitung

Ruijie

Ruijie RG-N18000-X Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6930-2C Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NIS3100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S5000-E Series Anleitung zur Verwendung

Ruijie

Ruijie Reyee RG-ES Series Bedienungsanleitung

Ruijie

Ruijie RG-S29 Series Installationshandbuch

Ruijie

Ruijie RG-ES100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2910-24GT4SFP-UP-H Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6580-48CQ8QC Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S7800 Series Handbuch

Ruijie

Ruijie RG-S6930-2C Installations- und Betriebsanleitung

Ruijie

Ruijie RGOS 11.X Bedienungsanleitung

Ruijie

Ruijie RG-CS85 Series Installations- und Betriebsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

Vimar

Vimar 6592 Montageanleitung