Ruijie RG-AP710 Series Installations- und Betriebsanleitung

Ruijie RG-AP710 Series Access Points

Hardware Installation and Reference Guide V1.00

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: [email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

Hardware Installation and Reference Guide Product Overview

1Product Overview

Featuring leading 802.11ac Wave2, Ruijie RG-AP710 supports 2 spatial streams and delivers up to [email protected]

(802.11b/g/n) and 2 spatial stream and delivers up to 867Mbps@5G (802.11a/n/ac). The overall dual-radio, dual-band

performance speeds up to 1167Mbps per device, totally eliminating Gigabit wireless bottlenecks. AP710 is ideal for a

variety of scenarios, such as large-scaled campuses, governments, financial services, and enterprises.

1.1 Technical Specifications

Table 1-1 Technical Specifications of RG-AP710

Hardware Specifications

Radio

2.4GHz: 2 x 2MIMO

5GHz: 2 spatial streams

Transmission

Protocol

Support concurrent 802.11b/g/n and 802.11a/n/ac.

Operating Bands

802.11b/g/n: 2.4 GHz to 2.4835 GHz

802.11a/n/ac: 5.15 GHz to 5.35 GHz, 5.47 GHz to 5.725 GHz, 5.725 GHz to 5.85GHz

(Depending on which country the AP is installed)

Antenna

Built-in antenna

Spatial Streams

2.4G supports 2 spatial streams, 5G supports 2 spatial streams

Access Rates

2.4GHz: up to 300Mbp

5GHz: up to 867Mbps

Total: up to1167Mbp

Modulation

OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and [email protected]/11Mbps

MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM and 256QAM

Receive Sensitivity

11b: -91dBm(1Mbps), -88dBm(5Mbps), -85dBm(11Mbps)

11a/g: -89dBm (6Mbps), -80dBm (24Mbps), -76dBm (36Mbps), -71dBm (54Mbps)

11n: -83dBm@MCS0, -65dBm@MCS7, -83dBm@MCS8, -65dBm@MCS15

11ac HT20: -83dBm (MCS0), -57dBm (MCS9)

11ac HT40: -79dBm (MCS0), -57dBm (MCS9)

11ac HT80: -76dBm (MCS0), -51dBm (MCS9)

Maximum Transmit

Power

20 dBm

(Depending on the country of use, laws and regulations.)

Transmit Power

Adjustment

1 dBm

Physical

Dimensions

(W x D x H)

194 mm x194 mm x 37 mm

(7.64in x7.64in x 1.46in)

Weight

0.42 kg

Service Ports

One 10/100/1000BASE-T Ethernet port (PoE-capable)

Hardware Installation and Reference Guide Product Overview

Management Ports

One Micro USB Console port

Button

One Reset button

LED

1 LED (red, green, blue, orange, and flashing modes, flashing mode for smart device access,

and the indicator can be switched off to silent mode)

Power Supply

Adapter: DC 5V/3A (optional)

PoE: IEEE 802.3af

Power Consumption

Maximum: 12.95W

Operating: -10°C to 50°C (14°F to 122°F)

Temperature

Storage: -40°C to 70°C (-40°F to 158°F)

Operating: 5% to 95% RH (non-condensing)

Humidity

Storage: 5% to 95% RH (non-condensing)

Installation

Ceiling/wall mount

IP Rating

IP41

Safety Standards

GB4943

IEC 60950-1

EMC Standards

GB9254

EN301 489

EN50155

EN50121

Vibration Standards

IEC61373

Radio

China Radio Transmission Equipment Type Approval Certificate

EN300 328

EN301 893

MTBF

>400,000H

The weight refers to the weight of host and bracket.

1.2 Product Image

The AP provides 5 ports, including 2 internal RF antenna ports, 1 Ethernet ports (PoE-capable), 1 Console port, and 1

power port for external power supply.

Figure 1-1 Top Panel of RG-AP710

Note

1. Laptop lock

4. LED indicator

Hardware Installation and Reference Guide Product Overview

2. Console port

3. Reset button

5. LAN1/PoE port

6. 5V DC power supply input port

1.3 LED Indicators

Fit AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

uBoot program initialization in progress

Solid green

N/A

Main program initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

Solid orange

N/A

Initialization is complete, and the AP is establishing a CAPWAP connection

with an AC.

Blinking orange

3Hz

Firmware upgrade in progress. Do not power off.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Blinking blue

3Hz

Normal operation, at least one wireless client is associated with the AP.

Pressed for less

than 2s

Restart the device.

Reset button

Pressed for more

than 3s

Restore default settings.

Fat AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

uBoot program initialization in progress

Solid green

N/A

Main program initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Blinking blue

3Hz

Normal operation, at least one wireless client is associated with the AP.

Pressed for less

than 2s

Restart the device.

Reset button

Pressed for more

than 3s

Restore default settings.

1.4 Power Sources

The AP can be powered either with a DC power adapter or through Power over Ethernet (PoE).

Hardware Installation and Reference Guide Product Overview

The AP requires Ruijie power adapters (If needed, you can buy them from Ruijie).

To use a PoE device, make sure it supports the IEEE 802.3af/at PoE standard.

1.5 Cooling Solution

The AP adopts fanless design.

Leave sufficient space at the surrounding of the AP when place the AP to permit airflow for proper ventilation.

Hardware Installation and Reference Guide Preparing for Installation

2Preparing for Installation

To prevent device damage and bodily injury, please read carefully the safety recommendations described in this

chapter.

The recommendations do not cover all possible hazardous situations.

2.1 Installation

The AP must be installed indoors. To ensure its normal operation, the installation site must meet the following

requirements.

Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling

system.

Make sure the site is sturdy enough to support the AP and its accessories.

Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.

Also, to avoid mutual interference, ensure the site is at least 2 meters away from a base station antenna.

Do not expose the AP to high temperature, dusts, or harmful gases.

Do not install the AP in an inflammable or explosive environment.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the seaside and do not face it toward the wind from the sea.

The installation site should be free from water flooding, seepage, dripping, or condensation.

The installation site shall be selected according to network planning and features of communications equipment, and

considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.

Please follow the correct method described in the installation guide to install and remove the device.

2.2 Movement

Avoid moving the device frequently.

Turn off all power supplies and unplug all power cables before you remove the device.

2.3 EMI

Please observe local regulations and specifications when performing electrical operations. Relevant operators must

be qualified.

Please carefully check for any potential danger in the working area, for example, damp/wet ground or floor.

Find out the location of the emergency power supply switch in the room before installation. First cut off the power

supply in case of an accident.

Hardware Installation and Reference Guide Preparing for Installation

Be sure to make a careful check before you shut down the power supply.

Do not place the device in a damp/wet location. Do not let any liquid enter the chassis

Keep the AP far away from the grounding or lightning protection devices of power equipment.

Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus

causing severe even fatal damages to human bodies and device.

Direct or indirect touch through a wet object on high voltage and power line can bring a fatal danger.

2.4 Ventilation

For proper ventilation, leave sufficient space around the AP.

2.5 Temperature and Humidity

To ensure normal operation and service life of the device, maintain appropriate temperature and humidity levels in your

equipment room. See Table 2-1. Improper room temperature and humidity can cause damages to the device.

High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage, and

sometimes may lead to change of mechanical properties of materials and corrosion of metal parts.

Low relative humidity may dry and shrink insulation sheets and cause static electricity that can damage the circuitry

inside the device.

High temperature greatly reduces reliability of the device and shortens its service life.

Table 2-1 Required Temperature and Humidity for the RG-AP710

Temperature

Relative Humidity

-10°C to 50°C (14°F to 122°F)

5% to 95%

2.6 Cleanness

Dust poses a serious threat to device operation. Dust that falls onto the surface of the device can be absorbed onto metal

contact points by static electricity, resulting in poor contact. Electrostatic absorption of dust occurs more easily when the

relative humidity is low, which may shorten the service life of the device and cause communication failures. Table 2-2

shows the maximum concentration and diameter of dust allowed in the equipment room.

Table 2-2

Maximum diameter (μm)

0.5

Maximum concentration

(Particles/m3)

1.4×107

7×105

2.4×105

1.3×105

Besides, the contents of salts, acids and sulfides in the air are also strictly limited for the equipment room. These

substances can accelerate metal corrosion and the aging of some parts. Table 2-3 describes the limit of some hazardous

gases such as SO2, H2S, NO2and Cl2 in the equipment room.

Hardware Installation and Reference Guide Preparing for Installation

Table 2-3

Gas

Average (mg/m3)

Maximum (mg/m3)

SO2

0.2

1.5

H2S

0.006

0.03

NO2

0.04

0.15

NH3

0.05

0.15

Cl2

0.01

0.3

2.7 Power Supply

DC power adapter: 5V/3A, 15W

Specifications of Connector

Internal Diameter

External Diameter

Depth

Polarity

2.10+/-0.05mm

5.50+/-0.05mm

10mm

Internal: positive External: negative

PoE injector: IEEE 802.3af/802.3at compliant

The DC input power should be greater than the power actually consumed by the system. The input power for the

RG-AP710 should be greater than 15 W.

Please use Ruijie recommended power adapters.

Please use Ruijie certified PoE injectors.

2.8 Installation Tools

Common Tools

Phillips screwdriver, related copper and fiber cables, bolts, diagonal pliers, cable ties

Special Tools

Wire stripper, crimping pliers, RJ-45 crimping pliers, punch down tool

Meter

Multimeter, bit error rate tester (BERT)

The listed tools are customer supplied.

2.9 Unpacking the Access Point

Package Contents

Items

Verify that all parts are installed and debugged.

Screws

Mounting brackets

Product quick installation guide

Packing list

Inhaltsverzeichnis

Andere Ruijie Drahtloser Zugangspunkt Handbücher

Ruijie

Ruijie RG-AP180 Series Bedienungsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie RG-AP740-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RAP6260-D Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP885-SP Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2260 Installations- und Betriebsanleitung

Ruijie

Ruijie AP850-AR Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2200 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP880-E Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP73HD Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AM5532 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP850-I-V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP880-AR Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-RAP1200-MNT Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-RAP52-OD Bedienungsanleitung

Ruijie

Ruijie RG-AP730-L Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-A Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee Series Abmessungen

Ruijie

Ruijie RG-SAP685-SP Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP740-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP825-SP Installations- und Betriebsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung