Russell Hobbs Reflections RHRSP1 Installationsanleitung

RECHARGEABLE SALT & PEPPER GRINDER

MODEL RHRSP1

Instructions & Warranty RHRSP1_IB02_141209

Please read the instructions and keep them safe. If you pass the appliance on, pass on the

instructions too. Remove all packaging, but keep it until you know the appliance works.

IMPORTANT SAFEGUARDS

Follow basic safety precautions, including:

XThis appliance must be used by or under the supervision of a responsible adult.

XDon’t put the appliance in liquid, don’t use it in a bathroom, near water or outdoors.

X 6WRUHWKHDSSOLDQFHDZD\IURPGLUHFWVXQOLJKWDQGLISRVVLEOHIURPÀXRUHVFHQWOLJKW

XDon’t run the motor for more than 1 minute, or it may overheat. After 1 minute, switch off

for at least 3 minutes to let the motor cool.

XDon’t use the appliance for any purpose other than those directed in the instructions.

XDon’t run the appliance empty. It may overheat.

XDon’t use the appliance if it’s damaged or malfunctions.

Before operating this appliance, the following safety points should be observed:

XInspect the plugs and cords. If any damage is found, please return for replacement or

 UHSDLUE\DTXDOL¿HGHOHFWULFLDQ

XOnly use the adapter provided for this appliance.

XDo not cut the cord or use the cord to lift the appliance. Keep it away from heat sources

and wet areas.

Do not clean the grinder while it is charging in it’s base. Please clean it while it is unplugged.

XDo not plug or unplug the power source with wet hands.

XOnly use a genuine charger from Russell Hobbs. Contact customer service if

replacement is required.

PRODUCT SPECIFICATIONS

Product name: Russell Hobbs Rechargeable Salt or Pepper Grinder

Model: RHRSP1

For use ONLY with transformer provided

Charging base input: DC 6V 500mA

Rechargeable battery: 2 x AA 1.2V 1000mAh Ni-MH (Nickel Metal Hydride) batteries

Measurement: 84mm x 84mm x 258mm

Weight: 850g approx.

PARTS AND ACCESSORIES TO THIS PRODUCT

a. Stainless Steel Casing h. *ULQGLQJ.QREFRDUVH¿QHSRZGHUVHOHFWLRQ

b. Control Switch i. Bulb

c. Rechargeable Battery j. Charging Jack

d. Battery Holder (irremovable) k. Charging Pilot Light (red)

e. Transparent Container l. Control Pilot Light (green)

f. Base m.Transformer (originally matched)

g. Charging Base n. Transformer Plug

ASSEMBLING THE GRINDER (Figure 1 & 2)

1. Align the pointers on the bottom of the motor unit with the

padlocks on the top of the grinder and lower the motor unit

on to the grinder.

2. The spindle should slide easily into the centre of the motor unit.

3. Lower the cover on to the motor unit.

4. Align the pointer on the cover with the open padlock ,push

the cover down, then turn it to align the pointer with the closed

padlock .

DISMANTLING

1. Grip the cover in one hand and the grinder in the other.

2. Turn the cover to move the pointer from to .

3. Lift the cover off.

CHARGING (Figure 3)

1. Remove the grinder and components from the packaging.

2. Plug the charger cord into the charging base, plug into the

socket and switch on the mains power. (the light on the base

will illuminate).

3. Sit the grinder on the base to charge (red charging light

will illuminate).

 &KDUJLQJZLOOWDNHDSSUR[KRXUVIRUWKH¿UVWWLPH2QFHIXOO\

charged, the green charge light will illuminate.

5. For longer battery life, leave the grinder to charge for up to 8

hours continuously.

Please note: the transformer and stainless steel

casing will become warm when charging is

completed. This is normal. It is recommended that

you remove the grinder from it’s base and let it

cool slightly before using.

FILL THE GRINDER (Figure 4)

1. Lift the motor unit off the grinder.

2. Fill the grinder with peppercorns, sea salt, dried herbs or spices.

 'RQRWRYHU¿OOWKHJULQGHURULWZRQ¶W¿WWRJHWKHU

4. Align the pointers on the bottom of the motor unit with the

padlocks on the top of the grinder and lower the motor unit

onto the grinder.

5. The spindle should slide easily into the centre of the motor unit.

6. Lower the cover on to the motor unit.

7. Align the pointer on the cover with the open padlock push the

cover down, then turn it to align the pointer with the closed

padlock .

Figure 1 Figure 2

Figure 3

Figure 4

ADJUST THE GRIND (Figure 5)

1. Turn the whole mill upside down and turn the knob right (-) until

it won’t go any further.

2. Now turn it left (+) a little.

3. Turn the mill right way up press and release the switch.

4. Check the grind size and adjust untill it is the way you want it.

5. Don’t turn it more than 6 complete turns towards + or you may

unscrew the knob from the spindle.

CARE AND MAINTENANCE

1. Wipe the outside of the mills with a dry cloth. Do not let them get wet or damp, do not

use detergent.

2. Do not use the mills over cooking as moisture can clog the grinding mechanism.

3. Clean the contact points on both the motor unit and grinder.

4. Wipe any excess Salt or Pepper from the underneath of the grinder.

 6HWWKHULJKWJUDQXOHVL]HE\DGMXVWLQJWKHFRDUVH¿QHVHWWLQJRQWKHXQGHUQHDWKRI

the grinder

6. Ensure you are using grinder grade Salt & Pepper.

BULB REPLACEMENT

1. The bulb is wire-ended in a plastic housing.

2. You need to remove the housing from the underside of the mill.

3. Turn the whole mill upside down.

4. Grip the plastic surrounding the bulb and pull it straight up.

5. You will feel some initial resistance, then it will come out.

6. Align the wires in the replacement bulb with the contacts inside the socket underneath

the mill and push the replacement bulb fully into the socket.

Figure 5

GENERAL TROUBLE-SHOOTING

Problem Possible Causes Trouble-shooting

XÍ Control Pilot Light “l” on

Íthe charging base does

Ínot illuminate.

XÍ No power. XÍ Check wall socket has

Íbeen switched on.

XÍ Check plugs are properly

Íinserted into charging

Íbase and wall socket.

XÍ Charging Pilot Light “k”

Íthe charging base does

Ínot illuminate.

XÍ

Grinder not properly

seated in charging base

XÍ Dirty charging contacts.

XÍ The green light is on “l”

Íbecause the battery is

Íalready fully charged.

XÍ Re-position grinder in

Ícharging base.

XÍ Clean contacts.

XÍ The grinder does not

Íoperate when the switch

Í“b” is pressed.

XÍ Improper installation of the

Ístainless steel casing and

Íthe transparent container.

XÍ Carefully align the arrow

Ísign of the stainless steel

casing withÍthe transparent

Ícasing lock symbol.

XÍ The bulb on the base “i” is

Ínot lit. XÍ Burnt-out or damaged

Íbulb. XÍ Replace bulb.

If your grinder does not function after checking through the items in the trouble-shooting

guide, please contact customer service.

Limited 2 year warranty

Nothing in this warranty or the instructions relating to the product excludes, restricts or otherwise

affects your statutory rights under the Trade Practices Act 1974 and other relevant legislation.

In addition to your statutory rights, Salton (Aust) Pty Ltd and Salton NZ Ltd (hereafter referred to as

“Salton”) provide a LIMITED 2 YEAR WARRANTY for this product. Salton warrants this product free from

defects in material and workmanship for two (2) years from the date of purchase. Within this warranty

period Salton will repair or replace defective parts at no charge. Defective products may be returned

to Salton or the place of purchase. Salton recommends you keep your receipt as proof of purchase. If

distance prevents you from taking the product to the place of purchase, please call the Salton

customer service department freecall within Australia 1800 427 842, or freecall within New Zealand

0508 629 777.

The warranty does not cover improper installation, misuse, abuse or neglect of the product. This

warranty also does not cover any product taken apart, altered or serviced by an unauthorised repairer.

Registration of your warranty card is not compulsory, but entitles you to receive these benefits:

Information on special price offers and promotions,

Notification of any issues concerning your product.

To register your product please:

9isit www.salton.com.auwarranty 2R

)ill in the warranty card below and send it to the address shown on the back

(email address must be supplied)

Received as a gift

Prior experience with Salton

Prior experience with Russell Hobbs

Recommendation of family/friend

Recommendation of Salesperson

Product features

Salton reputation

Russell Hobbs reputation

Ease of operation

Seen in store

Seen on television

Seen in newspaper/magazine

In store demo

Special offer

RH_WC_011209

Inhaltsverzeichnis

Andere Russell Hobbs Küchengerät Handbücher

Russell Hobbs

Russell Hobbs 13619 Installationsanleitung

Russell Hobbs

Russell Hobbs RHDF35D Bedienungsanleitung

Russell Hobbs

Russell Hobbs 14607 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPC1000 Series Installationsanleitung

Russell Hobbs

Russell Hobbs 25950 Bedienungsanleitung

Russell Hobbs

Russell Hobbs 26520-56 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RH1140 Installationsanleitung

Russell Hobbs

Russell Hobbs Illumina 20210-56 Bedienungsanleitung

Russell Hobbs

Russell Hobbs Temptations Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHSB150 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHBI46DZWC1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs 14452 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHBI18WC1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHBI7WC1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs 21850 -56 Bedienungsanleitung

Russell Hobbs

Russell Hobbs 20920 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHSP015 Installationsanleitung

Russell Hobbs

Russell Hobbs 20355-56 Bedienungsanleitung

Russell Hobbs

Russell Hobbs ROSETTA RHMS1 Installationsanleitung

Russell Hobbs

Russell Hobbs DualChef RHMC60 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMC1000 Installationsanleitung

Russell Hobbs

Russell Hobbs 12683 Installationsanleitung

Russell Hobbs

Russell Hobbs RU-23460-56 Bedienungsanleitung

Russell Hobbs

Russell Hobbs 24520 Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung