Rydeen BSS1 Bedienungsanleitung

Owner’s Manual

BSS1

Microwave Radar Blind Spots System

Version1.2

Table of Contents

I. Items List.............................................................................................................................................. 2

II. Technical Specification....................................................................................................................... 3

III. Wiring Diagram. .................................................................................................................................3

IV. Wire Connection Diagram................................................................................................................4

V. Installation Guide..............................................................................................................................5

VI. Alert Conditions............................................................................................................................... 8

VII. How does it Alert..............................................................................................................................9

VIII. Troubleshooting...............................................................................................................................9

IX. Technical Support Info..................................................................................................................10

X. Limited Warranty............................................................................................................................10

XI. To Obtain Warranty Service...........................................................................................................11

I. Items list

Number

Item Name

Quantity

Picture

Main Unit

1PCS

Main Harness

+ Extension Cable

1SET

Radar Sensor

2PCS

LED Indicator

2PCS

GPS Antenna

1PCS

Buzzer

1PCS

3M Velcro

4PCS

Tools for installation: angle gauge; insulation tape; multi-meter; screwdriver; cleaning cloth; tape.

II. Technical specification

Operating frequency

24.0 ----24.25GHZ

Transmit power

15dbm

Detection range

40 degree ( Horizontal )

Detection ability

5 targets can be detected at the same time

Speed range

0.5mph---137mph

Speed accuracy

< 0.5mph

Speed Restriction

1. The GPS Antenna when connected activates notifications

over 20mph (Example LED + Speaker)

2. If No GPS signal is detected or satellites not found, the

system will give notifications at any speed.

Direction of movement

Approached or overtaken by vehicles

Detection range

Truck : 1ft-60ft

Car : 1ft-50ft

Motorcycle:1ft-33ft

Pedestrian:1ft-23ft

Operating voltage

9---35V

Waterproof

Radars: IP65 / Cables: NOT waterproof

Working current

< 200mA

Working temperature

-40℃~ + 85℃

III. Installation Diagram

Red

Black

Red

Yellow

Pink

White/gray

Yellow

Orange

Green

Reverse Trigger

(Optional)

Black

IV. Wire Connection Diagram

GPS Ant

L_sensor

L_LED indicator

R_sensor

R_LED indicator

Buzzer

ACC/IGN

GND

N/A

L_lamp

R_lamp

V. Installation Guide

1. Sensor Installation

Installation requirements: sensors should be adhered to the inner corner of the bumper with

supplied Velcro. The angle should be between 20 to 25 degrees with the height ranging from

13-35 inches. (Fig.1-Fig.2)

Fig.1 Fig.2

Step1: Measuring method: Measure the rear bumper using the angle gauge to locate the 20 to 30

Degrees angle. (Fig.3-Fig.4)

The angle of the Microwave

radar sensors are between

20 to 25 Degrees.

The microwave sensors are only intended for

plastic bumpers.

Please note the BSS1 is NOT applicable for metal

bumpers.

Step2: Locate the desired position for the sensors. (Fig.5 - Fig.6)

Step3: Remove the rear bumper to clean the surface for the sensors. (Fig.7)

Fig7

Step4: Place the provided Velcro (To Help Absorb Vibration) on the surface of the

sensors (black side) and the desired location on the bumper (See image below).

Fig.8 Fig.9

Make sure the surface is

clean before Velcro

placed with sensors.

2. Installation of the left/right turn signal.

Step 5. Using the voltage Multi-meter, locate the left and right turn signal trigger wires behind

the tail lamp. Once verified, connect the left and right signal wires of the BSS1 wire harness to

the correct signal wires.

Fig10 Fig11 Fig12

3. LED indicator installation:

Step 6. Place the LED indicators where it is visible for the driver. Ideally on the A-pillar or in field

view side mirrors.

Fig.13 Fig.14

4. Speaker location:

Step 7. While installing the speaker, make sure it is not obstructed by any panels inside the

vehicle.

Fig.15

Step 8. Tuck the wires neatly to hide and prevent wire pinch.

Note

Illumination of the LED indicator on the control box:

1. The LED comes on solid when the system is first powered up;

2. The LED blinks slowly while the GPS module is connected to the satellite;

3. The LED blinks quickly while sensing moving objects that are approaching in the

blind spot (same frequency as to the alarm LED indicators & the buzzer);

4. The LED maintains the last blinking status after the alerts have ended (the last

blinking status of alarming is off / on randomly)

VI. Alert conditions:

1. When the vehicle is on, the system would start detecting objects in the blind area in the lane

next to and behind the vehicle 50 feet. (Fig.16)

2. When vehicles are approaching and their speed is faster than our own speed.

Fig.16

VII. How does it alert?

A: Blind detection on right side:

1. R-LED indicator will be activated when there is an object approaching to the right side blind

area of your vehicle (see Fig.16).

2. If the right turn signal of your vehicle is triggered at the same time, the R-LED indicator will be

blinking and the buzzer will be beeping as well (with the same frequency).

B: Blind detection on left side:

1. L-LED indicator will be activated when there is an object approaching to the left side blind area

of your vehicle (see Fig.16).

2. If the left turn signal of your vehicle is triggered at the same time, the L-LED indicator will be

blinking and the buzzer will be beeping as well (with the same frequency).

C: The LED and buzzer will standby (no activity) if there is no object approaching to the blind area

of your vehicle.

D: During reversing, the R & L LED will be blinking according to the approaching object detection

of each side.

VIII. Troubleshooting:

NO.

Issue

Reason

Solution

LED light does not

work

Incorrect connection or pins

not making contact

Check the harness and make

sure connection is correct

LED light is broken

Replace LED light

Opposite LED

indicator

Microwave sensor or LED

indicators are plugged in to the

opposite connector

Make sure RED is driver side and

YELLOW is passenger side.

Buzzer does not work

Wrong connection or pins not

making contact

Check the harness and make

sure connection is correct

Defective buzzer speaker

Replace buzzer

Sensors or GPS does

not work

Sensors or GPS module are

covered by the metal bumper

or other metal

Find the best location where the

GPS antenna cannot be blocked

by any metal

Unit does not work

after GPS is

connected

Blind spot system does not

trigger the sensors if the speed

is less than 20mph

Normal behavior in this case.

The GPS needs to detect

+20mph to trigger the sensors

IX. Technical Support Contact Info.

•Telephone:

1-877-777-8811

(within USA only)

•Email: [email protected]

•Web Address: www.rydeenmobile.com

Inhaltsverzeichnis

Andere Rydeen Autozubehör Handbücher

Rydeen

Rydeen MV311T Bedienungsanleitung

Rydeen

Rydeen MV332S Bedienungsanleitung

Rydeen

Rydeen DG240 Bedienungsanleitung

Rydeen

Rydeen MV437FL Bedienungsanleitung

Rydeen

Rydeen CM-T1000P Bedienungsanleitung

Rydeen

Rydeen TOMBO ProKit Bedienungsanleitung

Rydeen

Rydeen rdv360II Bedienungsanleitung

Rydeen

Rydeen PSR4000D Bedienungsanleitung

Rydeen

Rydeen BF-450PM Bedienungsanleitung

Rydeen

Rydeen BL-422P Bedienungsanleitung

Rydeen

Rydeen BSS2 Bedienungsanleitung

Rydeen

Rydeen BP1 Bedienungsanleitung

Rydeen

Rydeen BSS3 Bedienungsanleitung

Rydeen

Rydeen MD4BT Bedienungsanleitung

Rydeen

Rydeen BB-400PM Bedienungsanleitung

Rydeen

Rydeen BM500S Bedienungsanleitung

Rydeen

Rydeen BSS3 Bedienungsanleitung

Rydeen

Rydeen MV432T Bedienungsanleitung

Rydeen

Rydeen CM-AHD1 Bedienungsanleitung

Rydeen

Rydeen MV311S Bedienungsanleitung

Rydeen

Rydeen 360 VIEW Bedienungsanleitung

Rydeen

Rydeen SV747HD Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung