Salus Quantum SQ610 Bedienungsanleitung

IX 2019

2 3

Introduction

The SQ610 Quantum is a ZigBee temperature controller for wireless control of iT600 series devices, such as the

KL08RF wiring centre, mini TRV head, RX10RF boiler control module.

In order to control SQ610 over the Internet or via the SALUS Smart Home mobile app (ONLINE mode), it

must be installed together with the UGE600 Internet gateway (sold separately). From the application level, it

is possible to pair SQ610 with other system elements, e.g. Smart Plug SPE600, Smart Relay SR600 or window/

door sensor OS600/SW600.

SQ610 can be used locally without an Internet connection (OFFLINE mode), however, it’s communication with

other devices must be done using the CO10RF coordinator (sold separately).

Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition. Product for

indoor use only. Installation must be carried out by a qualied person in accordance to national and EU regulations.

Disconnect your equipment before cleaning it with a dry cloth.

Please always ensure the AC 230V mains power is switched o before installing or working on any components.

Product Compliance

Safety Information

Warning:

This product complies with the essential requirements and other relevant provisions of Directives 2014/30/ EU,

2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the

following internet address: www.saluslegal.com.

Before you start: Wiring diagram:

Symbols explanation:

S - volt-free contact

T - temperature sensor

L, N - 230V AC pover supply

COM, NO -Voltage free output

S1,S2 Terminals:

- air or oor temperature sensor

- external volt-free contact to connect any ON/

OFF switch or occupancy sensor (Hotel card)

Mounting: to mount thermostat you can use included

accessories (mounting screws). Remove plate from

the back to mount it to the wall. After that just put

thermostat on the plate.

Please note:

The ideal position to thermostat mounting is about 1,5m

under oor level far from heating or cooling sources.

Thermostat can’t be exposed to sunlight or any extreme

conditions like for example draft.

Package Content:

1) SQ610 Quantum Thermostat

2) Mounting screws

3) Manual instruction

COM

SQ610

NO L

230V~,50Hz

S1 S2

150 cm

min 20 cm

Select correct thermostat location

THERMOSTAT SQ610 Quantum can work without Universal Gateway or CO10RF Coordinator as a standalone device.

Full manual in PDF format is available at www.salus-controls.eu site.

AC 230V

Français Deutsch

Nederlands English

4 5

1. Menu/Settings description + Clock

2. AM/PM

3. Temperature unit

4. Heating indicator (icon is animating when

there is heating demand)

5. Cooling indicator (icon is animating when

there is cooling demand)

6. RF Connection indicator

7. Internet connection indicator

8. Occupancy sensor (hotel card)

9. Key lock function

10. Standby mode icon

11. Current Temperature / Setpoint Temperature

12. Holiday mode

13. Temporary override mode

14. Settings icon

15. External / Floor temp sensor indicator

16. Schedule program number

17. Schedule mode icon

18. Day indicator/ SET information

19. Current Humidity value

10111214

LCD Icon Description

Buttons DescriptionButtons Description

1) Menu button / Return button.

2) In the MAIN SCREEN: Press and hold for 3 sec to change the thermostat operating mode

(Schedule mode / Permanent mode / Temporary override mode).

3) In the SETTINGS SCREEN:

Press and hold for 3 sec to go back without saving the changes.

4) In the PAIRING SCREEN (in SYSTEM TYPE Menu): Press and hold for 3 sec to see other

pairing options.

In the MAIN SCREEN - press and hold these buttons together for 3 seconds to LOCK / UNLOCK

the Thermostat keys).

“Up”Button (Increase parameter value/moving on the menu in‘UP’direction)

„Down”Button (Decrease parameter value/moving on the menu in‘DOWN’direction)

1)“OK / Tick”Button (Conrm parameter value / Go to the next menu / Save settings)

2) In the MAIN SCREEN: Press and hold for 3 seconds to enter Standby mode

3) In the SETTINGS SCREEN: Press and hold for 3 sec to go back to the MAIN SCREEN & SAVE all the changes.

Button Function

Français Deutsch

Nederlands English

6 7

COMPATIBILTY WITH OTHER SALUS CONTROLS DEVICES

Quantum Thermostat can work in ONLINE or OFFLINE mode. *Quantum Thermostat can work in ONLINE or OFFLINE mode. *

At rst step you need to decide in which mode your thermostat will work.At rst step you need to decide in which mode your thermostat will work.

ONLINE MODE OFFLINE MODE

Universal Gateway is

CONNECTED TO THE INTERNET

You can congure and use all your

devices in the Smart Home App

Download the Smart Home

App on your iOS or Android

device for remote access to your

SALUS equipment. SALUS

Smart Home

CO10RF Coordinator - You can use

standard ZigBee network coordinator

to install and use your devices.

Universal Gateway is NOT

CONNECTED TO THE INTERNET

You can use your devices locally

without the SmartHome App.

Gateway works in this mode as

standard ZigBee coordinator.

Compatibile devices:

KL08RF

Wiring Centre for 8-zone

underoor heating (UFH).

TRV

(Thermostatic

Radiator Valve) with

wireless communication.

RX10RF

receiver

First power up sequence

To power on the Thermostat you

have to connect it to the 230V power

then...

For easier installation, please make sure you have already added other devices to your ZigBee network, such as

Underoor Heating Control Box (KL08RF) or Radiator heads (TRV’s) etc.

Please note:

Now, choose your language by

„” or „ ”buttons. Conrm

your language by button.

...display will showall icons... ...then thermostat will display

the software version.

SR600*

Smart Relay

SPE600*

Smart Plug

SQ610 Quantum Thermostat can work without coordinators (ONLINE/

OFFLINE MODE) as a standalone device with the wires use.

*Only with Online Mode

Thermostat work as a standalone device

for pump, boiler, receivers etc. That is, you

can directly connect thermostat to selected

device without any network system. You

can add it later anytime.

NO - STANDALONE.

You can congure your thermostat

with universal gateway or CO10RF

coordinator.That is, add it to the Salus

Smart Home system.

GET IT ON

Download on the

Please note:

Français Deutsch

Nederlands English

YES - ONLINE, OFFLINE MODE.

8 9

Installation in ONLINE mode

After Language selection follow below steps to add your device to the Smart Home app and pair with other devices:

SALUS

SmartHome

Go to SALUS Smart Home app

Français Deutsch

Nederlands English

Once your thermostat is added to

the app you will see above screen

on the LCD.

45 6

After that thermostat will show

main screen.

Congratulations!

You succesfully configured SQ610

QuantumThermostat.

1211

Name this equipment

SQ610 230V Thermostat

Connect equipment

Finish

10 11

Installation in OFFLINE mode

123

Open the ZigBee network

456

Select system type: UNDERFLOOR,

press button to conrm

Using and buttons select the Control

Box number (press PAIR button on the Control

Box to see its address number). Press button

to conrm

Use or buttons to select

the zone number and press

button to conrm.

Now you can pair your thermostat

with additional zones. Select one

more zone or nish the pairing

process by button.

5 sec

Close the ZigBee network

5 sec.

5 sec

Pairing with Wiring Centre / Control Box (Installthe Wiring Centre / Control Box according to the

instructions included with product)

Open the ZigBee network

Select system type:

RADIATORS

Now hold antenna button for 10

sec. on all TRV’s which you want

to pair with your Termostat.

Pairing with TRV radiator head (Install the TRV accordingtothe instructionsincludedwith

product)

On the LCD you will see the number of

pairedTRV’s. Once allTRV’s are paired - press

button to nish the pairing process.

5 sec

5 sec.

10 sec

Close the ZigBee network

5 sec

You can pair up to 6 TRV’s with

1 Thermostat. All TRV’s have

to within the same room with

Thermostat.

Français Deutsch

Nederlands English

12 13

Wired device

Thermostat SQ610 Quantum can work without Universal Gateway or CO10RF Coordinator as a standalone device.

Please note:

Wiring diagram for volt-free connection (e.g. boiler control):

2Wiring diagram for 230VAC connections:

Wiring diagram for control box connection:

1-8 Zones

SLL

AC 230V

Power

AC 230V

BOILER CONNECTIO

AC 230V

COM NO

COM

Legend:

Boiler connection * - Boiler’s contacts

for ON/OFF thermostat (according to the

boiler’s instructions)

Pump

Boiler

Valve actuator

Heating mat

KL08NSB

Self-acting SQ610 Quantum Thermostat without application support can be easily added to the

Smart Home app anytime. All settings made before adding to the application are automatically

copied to the Smart Home app.

MAX 3(1)A

Français Deutsch

Nederlands English

14 15

SQ610 Full menu structure

Schedule settings

User settings

Admin settings

Language

TIME/DATE

HOLIDAY MODE

THERMOSTAT CALIBRATION

SHOW/HIDE DISPLAY HUMIDITY

SHOW/HIDE DISPLAY FLOOR

STANDBY TEMP SETPOINT

HEAT/COOL

RESET USER SETTINGS

ENGLISH

DANISH

POLISH

...

DISABLE

MO-FR+SA-SU

MO-SU

SINGLE DAYS

Main menu

TEMPERATURE SCALE

DISPLAY TEMPERATURE RESOLUTION

HEAT CONTROL ALGORITHM

COOL CONTROL ALGORITHM

S1/S2 INPUT

MINIMUM SETPOINT

MAXIMUM SETPOINT

VALVE PROTECTION

INTERNAL RELAY (NO / NC)

MINIMUM TURN OFF TIME

OPTIMISATION FEATURE

COMFORT WARM FLOOR

PIN CODE

DEVICE INFORMATION

CONNECT WITH GATEWAY

FACTORY RESET

10.*

Short description of some selected functions

(all functions are described in the full version of the SQ610 manual):

1. DISPLAY TEMP RESOLUTION: This function determines the resolution of the displayed

temperature ( 0.5°C or 0.1°C ).

2. CONTROL ALGORITHM: This function denes how to control the room temperature. Available

options are: ITLC for Underoor Heating / Radiators / Electrical Heating (that’s advanced algorithm for

precise maintenance of room temperature), hysteresis +/-0.5°C or +/-0.25°C, THB Actuator (option

recommended for systems withTHB auto balancing actuators).

3. S1/S2 INPUT: A oor sensor, an external temperature sensor or an occupancy sensor can be

connected to the S1/S2 input of SQ610RF. Additionally, by connecting a NO type of ON/OFF voltage-

free contact, you can use this input as a OneTouch rules trigger (programmed in the Salus Smart Home

app) or as a Heat/Cool changeover.

4. VALVE PROTECTION: This function activates all actuators once a week for 5 minutes (in summer,

this function helps to prevent the actuators stuck).

6. MIN TURN OFF TIME: Minimum switch-o time (thermostat will not send the signal for

heating/cooling more often than specied in this parameter).

7. OPTIMISATION FEATURE: Optimum Start and Optimum Stop functions are energy saving feature

that makes thermostat most cost eective (in combination with ITLC control algorithm).

9. DEVICE INFORMATION: In this menu user can check: Software Version, RF range value, Paired

devices or also user can activate Identication mode.

*10. FACTORY RESET: Here you can RESET your device to factory settings. After successfull reset

device will be removed from ZigBee network and you will need to add / pair your device again.

8. COMFORT WARM FLOOR: This function helps to keep the oor warm, even if the room is warm

enough and there is no need to turn on the heating. User can select 3 levels of warm oor feature.

Please note it is not an economy feature, as your heating system may be ON even if there is no heating

demand from the room thermostat. It is COMFORT feature which keeps your oor warm all the time.

5. INTERNAL RELAY (COM/NO): Internal relay activation or deactivation with COM/NO outputs use. Default

is enable.

Français Deutsch

Nederlands English

58 59

QUANTUM SQ610

Power Supply AC 230 V

Temperature range 5-40°C

Display temperature accuracy 0.5°C or 0.1°C

Control algorithm ITLC

SPAN

(±0.25°C / ±0.5°C)

THB

S1-S2 Input

(multifunctional input)

Floor temperature

Air temperature

Occupancy sensor

One Touch

Changeover

(heating/cooling)

Output control COM – NO

(volt-free)

Max current 3 (1) A

Communication protocol ZigBee 2,4GHz

Mounting Flush mounting

Working temperature 0-45°C

IP protection class IP30

Dimensions

[Width x Height x Deep]

86 x 86 x 10 mm

Thickness after mounting in a

wall-box φ60

10 mm

English

Andere Handbücher für Quantum SQ610

Inhaltsverzeichnis

Andere Salus Thermostat Handbücher

Salus

Salus RT310SR Bedienungsanleitung

Salus

Salus ERT30RT Bedienungsanleitung

Salus

Salus RT510WBC Bedienungsanleitung

Salus

Salus AWRT10RF Bedienungsanleitung

Salus

Salus 091FLRF Bedienungsanleitung

Salus

Salus RT500 Bedienungsanleitung

Salus

Salus RT310TX Bedienungsanleitung

Salus

Salus RT100 Bedienungsanleitung

Salus

Salus DIGITAL PROGRAMMABLE THERMOSTAT Bedienungsanleitung

Salus

Salus RT310SPE Bedienungsanleitung

Salus

Salus TH-3 Bedienungsanleitung

Salus

Salus RT510BC+ Bedienungsanleitung

Salus

Salus HTR2420 Bedienungsanleitung

Salus

Salus EP101 Bedienungsanleitung

Salus

Salus BTRP230 Bedienungsanleitung

Salus

Salus RT510RF Bedienungsanleitung

Salus

Salus RT310iSPE Bedienungsanleitung

Salus

Salus RT200 Bedienungsanleitung

Salus

Salus HTRS230 Benutzerhandbuch

Salus

Salus Quantum WQ610 Bedienungsanleitung

Salus

Salus SQ605RF Bedienungsanleitung

Salus

Salus RXRT505 Bedienungsanleitung

Salus

Salus VS35W Bedienungsanleitung

Salus

Salus QUANTUM SQ610RF Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung