Samsung SADT-103WM Bedienungsanleitung

SADT - 103WM

Wall Mount Adaptor

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please

www.samsung.com/global/register

SADT-103WM_ENG.indd 1 2008-03-18 오전 9:13:51

ENG

SADT-103WM_1

Overview

The Wall Mount Adapter is used to install the OUTDOOR

HOUSING (SHG-221/222) on the indoor/outside wall.

Notice

• Make sure that you must select an installation spot to endure the total weight of "Wall

Mount Adapter", "Outdoor Housing" and "Smart Dome Camera".

•This product is designed to use with anchor bolts and anchor nuts (M10).

• If installing in a concrete wall, use a M10 anchor bolt (nut) with ﬂat washer and spring

washer.

•Each installed anchor bolt should endure 700kg of pulling force.

• Wall Mount Adapter can be installed directly in the wall, and also attached to CORNER

MOUNT ADAPTOR(SADT-110CM), or POLE MOUNT ADAPTOR(SADT-100PM). At this

time, please use the PG-13.5 cable grand.

Installation

1. Select an installation spot which can endure more than 4 times of the product weight.

2. Refer to the following wring diagram to prepare cables necessary for connecting the

Outdoor Housing.

SADT-103WM_ENG.indd 1 2008-03-18 오전 9:13:51

2_SADT-103WM

The wiring diagram to connect the outdoor cable of the OUTDOOR HOUSING(SHG-221/222)

3. If you mount the Wall Mount Adaptor on the wall, mark a hole where you insert the anchor

bolt or anchor nut (M10) using the Cover Plate, and drill a hole for the anchor bolt (nut).

If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM).

If installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM) for this

purpose.

COVER PLATE

The hole for joining

a ANCHOR BOLT

150 mm

80 mm

SADT-103WM_ENG.indd 2 2008-03-18 오전 9:13:52

ENG

SADT-103WM_3

4. Prepare the Holder Housing from the Outdoor Housing and insert the cables of the Holder

Housing into the Wall Mount Adaptor before pulling them out through the hole of the

Cover Fixing Part.

5. Fit the Guide of the Holder Housing into the corresponding Guide Hole of the Wall Mount

Adaptor while inserting the Holder Housing into the Wall Mount Adaptor.

- Install the Holder Housing so that the “FRONT” label faces the front of the camera.

- Make sure that the Bush Cable should not be loose from the Holder Housing.

(If the Bush Cable is not secured ﬁrmly, the product is not properly waterproof.)

HOLDER HOUSING

WALL MOUNT ADAPTOR

BUSH CABLE

GUIDE HOLE

GUIDE

WALL MOUNT ADAPTOR

CABLE

HOLDER HOUSING

The place for

joining a COVER

WALL MOUNT ADAPTOR

HOLDER HOUSING

SADT-103WM_ENG.indd 3 2008-03-18 오전 9:13:53

4_SADT-103WM

6. Turn the Holder Housing clockwise by 18 degrees. Then, use 3 screws(M4×L8,

suported), to ﬁx the Holder Housing to the Wall Mount Adaptor.

7. According to the status of connected cable of the OUTDOOR HOUSING, SHG-221/222),

a way of installation is different as follows.

If the cable pipe is installed inside of the wall

Use the Cable Grand to connect the external cables with the Cover Plate.

- You should use only the Grand Cable for waterproof purpose. Furthermore, it is

recommended to keep the cable about 150mm longer than the Cover Plate.

COVER PLATE

150 mm

CABLE GRAND

WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR

HOLDER

HOUSING

HOLDER HOUSING

SCREW

Turn to the clockwise

about 18 degrees

SADT-103WM_ENG.indd 4 2008-03-18 오전 9:13:54

ENG

SADT-103WM_5

If you use only the Grand Cable to ﬁx the cables to the Cover Plate, the other hole of

the Cover Plate should be sealed up with the Rubber Cap for waterproofness.

The different cables on the Cover Plate can be pulled out through the hole of the Cover

Fixing Part of the Wall Mount Adaptor. 4) Then, use 6 screws (Flat, M3xL8) to ﬁx the

Cover Plate to the Wall Mount Adaptor.

Make sure that the Gasket part should keep contact with the Wall Mount Adaptor

during the ﬁxation.

COVER PLATE

150 mm

CABLE GRAND

RUBBER CAP

WALL MOUNT ADAPTOR

The place for joining a COVER

GASKET COVER PLATE

SCREW

SADT-103WM_ENG.indd 5 2008-03-18 오전 9:13:55

6_SADT-103WM

If the cable pipe is installed outside of the wall

Drill a 21mm-diameter hole on the Wall Mount Adaptor (side and top, respectively).

For your reference, see the ﬁgure below.

- The drilling process for the Wall Mount Adaptor must be performed prior to the

ﬁxing process of the Holder Housing according to the steps 4, 5, 6 in this installation

guide.

Put two Rubber Caps upon the Cover Plate.

Make sure you do this as it is necessary for waterprooﬁng.

COVER PLATE

RUBBER CAP







* Drilling Points (unit: mm)

(a) Top (b) Side

SADT-103WM_ENG.indd 6 2008-03-18 오전 9:13:56

ENG

SADT-103WM_7

Use the Grand Cable to ﬁx the necessary cables to the Wall Mount Adaptor before

pulling them out of the hole of the Cover Fixing Part.

Use 6 screws (Flat, M3xL8) to ﬁx the Cover Plate to the Wall Mount Adaptor.

Make sure that the Gasket part should keep contact with the Wall Mount Adaptor

during the ﬁxation.

8. Use the anchor bolt and nut to secure the Wall Mount Adaptor to the wall.

WALL MOUNT ADAPTOR

GASKET

COVER PLATE

SCREW

WALL MOUNT ADAPTOR

ANCHOR BOLT

WALL MOUNT ADAPTOR

CABLE GRAND

The place for

joining a COVER

SADT-103WM_ENG.indd 7 2008-03-18 오전 9:13:57

8_SADT-103WM

9. See the wiring diagram below for connecting the cables of the Camera Adaptor.

A. Remove one of the Connectors connected to the cable end of the Camera Adaptor.

B. Peel off the coating on the cable end of the Connector and connect it to the external

cable using soldering.

(See the cable wiring diagram in the installation guide of the Camera for connecting the

cables.)

C. Use an insulation tape to wrap up the soldering portion of two cables.

D. Connect the Connector to the Camera Adaptor again.

E. Repeat the above 4 steps to connect all of the 4 Connectors to the corresponding

external cables.

F. In the last step, connect the BNC jack.

CAMERA ADAPTOR CAMERA ADAPTOR

CABLE

CONNECTOR

BNC JACK

CONNECTOR

Soldering

External Cable

SADT-103WM_ENG.indd 8 2008-03-18 오전 9:13:59

ENG

SADT-103WM_9

10. Insert the joined cable into the Wall Mount Adaptor through the Cover Fixing Part.

Insert one piece of the two-strand cable into an empty area of the Wall Mount Adaptor

as in the ﬁgure below and push the other one into the Wall Mount Adaptor.

(Ensure that the insulated coating of the cable should be kept intact while the insertion)

11.Use 2 screws (M3xL4, suported) to ﬁx the Cover to the Wall Mount Adaptor.

WALL MOUNT ADAPTOR

SCREW

COVER

WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR

< Insert one piece of the two-stranded cable > < Insert the other piece of the two-stranded cable >

the place for joining a cover

SADT-103WM_ENG.indd 9 2008-03-18 오전 9:14:01

Andere Handbücher für SADT-103WM

Inhaltsverzeichnis

Andere Samsung Rack & Stand Handbücher

Samsung

Samsung WMN3000C Series Bedienungsanleitung

Samsung

Samsung 46UE Bedienungsanleitung

Samsung

Samsung STN-SF40 Bedienungsanleitung

Samsung

Samsung Wisenet SBP-160TM Bedienungsanleitung

Samsung

Samsung WMN-7070 Bedienungsanleitung

Samsung

Samsung LFD EX Series Bedienungsanleitung

Samsung

Samsung WMN550M/XC Bedienungsanleitung

Samsung

Samsung SBP-300NB Bedienungsanleitung

Samsung

Samsung WMN550M Bedienungsanleitung

Samsung

Samsung SCX-300CM Bedienungsanleitung

Samsung

Samsung Harman AMX VARIA-ACS-810A Bedienungsanleitung

Samsung

Samsung SADT-100EC Bedienungsanleitung

Samsung

Samsung Sbr-100dcm Bedienungsanleitung

Samsung

Samsung WMN750M/XC Bedienungsanleitung

Samsung

Samsung WMN-M21E Bedienungsanleitung

Samsung

Samsung WMN350M Bedienungsanleitung

Samsung

Samsung WMN-M13E Bedienungsanleitung

Samsung

Samsung WMN-M22E Bedienungsanleitung

Samsung

Samsung CY-SMN1000D Bedienungsanleitung

Samsung

Samsung SBP-300HM4 Bedienungsanleitung

Samsung

Samsung WMN-M20E Bedienungsanleitung

Samsung

Samsung TWMB-1900 Bedienungsanleitung

Samsung

Samsung WMN-M15EB Bedienungsanleitung

Samsung

Samsung WMN-M12E Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung