Samsung VC-U366 Bedienungsanleitung

Vacuum

Cleaner

For Household

use Only

Operating

Instructions

Read these instructions before operating the vacuum cleaner

※The design and specification may be different depending on the models.

Safety Instructions

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical appliance,

basic precautions should always be followed, including the following:

PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS APPLIANCE

To reduce the risk of fire, electric shock, or injury:

·Do not leave appliance unattended when plugged in. Unplug the vacuum from the outlet

when it is not in use, or when it is being cleaned.

·Do not use outdoors or on wet surfaces.

·Do not allow to be used as a toy. Close attention is necessary when used by or near

children.

·Use only as described in this manual. Use only manufacturer’s recommended

attachments.

·Do not use with damaged cord or plug. If appliance is not working as it should, or has

been dropped, damaged, left outdoors or dropped in water, take it to a service center.

·Do not pull or carry the vacuum by the cord, or use the cord as a handle. Do not close a

door on cord, or pull the cord around sharp edges or corners. Do not run the appliance

over its cord. Keep the cord away from heated surfaces.

·Do not unplug the vacuum by pulling on the cord. To unplug, grasp the plug, not the

cord.

·Do not handle plug or appliance with wet hands.

·Do not put any object into vacuum openings. Do not operate with any opening blocked:

Keep free of dust, lint, hair and anything that may reduce air flow.

·Keep hair, loose clothing, fingers and all parts of body away from openings and moving

parts.

·Do not use to pick up anything that is burning or smoking, such as cigarettes, matches

or hot ashes.

·Do not use without dust bag and filters in place.

·Turn off all controls before unplugging.

·Use extra care when cleaning on stairs.

·Do not use to clean up flammable or combustible liquids such as gasoline. Do not use

the vacuum in areas where such liquids may be present.

·Store your cleaner indoors in a cool, dry area.

·Do not use extension cords or plug into an electrical outlet with inadequate current

carrying capacity.

·Avoid vacuuming up sharp objects.

·Always turn this appliance off before connecting or disconnecting the hose, replacing

bags, or removing the bottom plate for maintenance.

·Unplug electrical appliances before vacuuming them.

To reduce the risk of electrical shock, this appliance has a polarized plug with one blade

wider than the other. This plug will fit in a polarized outlet only one way. If the plug does

not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

replace the outlet. Do not change the plug in any way.

Warning:

Save these instructions!

Assembling Parts

The assembled cleaner will look like the illustration to the left.

Hose Clip Handle

Power Switch

Louvers

Upper Tank

Frame and

Filter(Inside

Louvers)

Upper Tank

Post-Motor Filter

Hepa Media Filter

(Optional Item)

Lock ’n Seal™

Lever

Handle

Release Pedal

Furniture Protection Guard

Powerfoot

Height

Adjustment

Knob

Pre-Motor Filter

Dirt Container

Power Cord

Stretch Hose

Quick Release

Cord Wrap

Carrying

Handle

Quick Reach

Handle

Hose WandDusting Brush

Extension Wand

Upper Tank Knob

Crevice Tool

Hose

Wand Base

Locate the vacuum

Handle and remove the

screw packet taped to

the base of the Handle.

Stand the vacuum

upright and slide the

base of the handle firmly

into the grooves at the

top of the vacuum body.

Check to be sure the Handle

is fitted to the vacuum body.

If there is a gap in front,

continue to push firmly until

the Handle is flush.

Insert one screw provided

from the screw packet into

the existing hole. Tighten

securely with a Philliphs

head screwdriver.

1-1 1-2

Position the Hose

Assembly on the

back of the

vacuum as shown.

Attach the Hose

with the remaining

two screws from

the packet.

Tighten securely

with a screwdriver.

Grasping the Quick

Reach Handle, slide the

end of the Hose Wand

onto the Hose Wand

Base. Snap the Hose

into the Hose Clip.

NOTE: The Powerfoot

will not operate

effectively unless the

Hose Wand is firmly

attached.

Slide the

Extension

Wand and

the Crevice

Tool together

into the

storage clip

as shown.

Slide the Dusting Brush Tool into

the storage clip as shown.

1-3 1-4 1-5

Step 1. Attaching the Handle

Step 2. Attaching the Hose and Tools

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

1. How to put it together.

Assembled Vacuum Cleaner Parts

Operation

Dusting Brush Tool:

Use to dust furniture, blinds, books,

lamps, shelves, draperies, cushions.

Crevice Tool:

Use in tight narrow spaces.

Extension Wand:

Use with desired attachment for a

longer reach.

The cleaner can also be moved by

using the carrying handle.

2-4 2-5

Attachment tools can be used to clean

furniture or drapes, on stairs or in

corners. Place the vacuum on the floor

with the handle in the upright position.

2-1 2-2 2-3

1.To turn cleaner ON(I), press the

ON/OFF switch to the ON position.

2.To the cleaner OFF(O), press the

ON/OFF switch to the OFF position.

The handle of your cleaner has three

positions; upright for storage and

when using cleaning tools; operating

for general operation on carpet and

floors; low for reaching under low

furniture. Step on handle release

pedal to lower handle.

To move your cleaner from room to

room, put the handle in upright

position, tilt the cleaner back on its

rear wheels and push forward.

CAUTION:

WARNING:

NOTICE:

While vacuuming, certain carpets

and low humidity conditions may

generate small static discharges.

The discharges are entirely

harmless and are not associated

in any way with the main power

supply.

NOTICE:

The Floor Brush will continue to

rotate while you use your vacuum

for above floor cleaning. To prevent

carpet damage, do not lean on the

vacuum or let the Powerfoot tilt

forward.

2. How to use you samsung vacuum

ON-OFF Switch

Carrying handle

Cleaning Tool attachments

Handle positions

Transporting cleaner

To maintain maximum cleaning

performance, the following

maintenance steps must be

performed:

Empty the Dirt Container when the

dirt reaches the “Full” line on the

side.

Check the Upper Tank and Pre-

Motor Filters monthly and clean or

replace as needed.

Clean or replace the Post-Motor

Filter every three months.

Note: More frequent filter

cleaning may be necessary if

you are vacuuming new carpet,

fine dust, or have allergy

concerns. Follow the

instructions on the following

pages to perform these simple

maintenance steps.

The Rotating Floor Brush continues

to rotate while tools are in use. To

reduce the risk of injury from moving

parts, always move the cleaner with

the Carrying Handle at the back of

the cleaner. Always place vacuum

cleaner on floor with Handle in

Upright position when using tools.

Never place your fingers under the

cleaner when it is running. Never

place Powerfoot on furniture or

uneven surfaces. Do not place

vacuum cleaner close enough to

objects to pull them into rotating

brush.

To reduce the risk of electric

shock, turn Power Switch OFF

and disconnect plug from

electrical outlet before

performing mainte- nance or

troubleshooting checks.

Maintenance

The Dirt Container needs to be

emptied when the dirt reaches

the “Full” line on the side of the

Container.

①Unplug the cleaner from electrical

outlet.

②Slide the Lock ‘n Seal Lever to

the "Unlock" position.

③Grasp handle and pull the Dirt

Container straight out to remove

from vacuum.

④Empty dirt into garbage

container.

⑤Put the Dirt Container back in the

vacuum and slide the lever to the

"Lock" position.

①Unplug the cleaner from electrical

outlet.

②The Upper Tank Filter can be

reached by removing the Dirt

Container, reaching underneath the

Upper Tank and turning the rim of

the Filter Frame to unlock. Pull

straight down to remove. Brush the

dirt off the Louvers and Upper Tank

Filter.

③The foam Upper Tank Filter may be

removed and hand washed in cold

water with mild detergent. Rinse

well then air dry thoroughly before

replacing.

④The Upper Tank and Louvers may

also be wiped clean with a damp

cloth.

3-2

3-3

3-1

Full Line

Lock Position

Unlock

Position

Stand on one end of rug and move

cleaner toward other end or edge.

Before reaching edge, push down on

handle. This will lift up the nozzle(front of

cleaner)and will prevent rug from clinging

to cleaner.

Continue to lift front of cleaner so that

when you have reached the edge, it is

completely off the rug. Move cleaner

back to start again, lower front of cleaner,

and use only forward strokes.

Carpet and rug cleaning takes place at the

nozzle (A).

When it is necessary to raise and lower the

nozzle for various carpet pile heights, rotate

the nozzle control knob (B) to the desired

setting.

For maximum cleaning performance, The

following carpet height settings are recommended:

·Lowest setting: for all types of carpet

·Higher settings: for very deep pile carpet where

easier pushing effort is desired, while maintaining

good cleaning performance.

Note: If the cleaner is difficult to push, rotate knob to

the next higher setting.

To change the power level of the vacuum

cleaner, rotate the knob.

2-6 2-7

2-8

2-9

Note: The Dirt Container may

be washed in warm water

with a mild detergent. Make

sure it is completely dry

before using again.

3. How to maintain youer samsung vacuum

Carpet height adjustment

Power control

(some models only)

Empty Dirt Container

Cleaning lightweight flexible rugs

Cleaning The Upper Tank & Filter

Maintenance

The Pre-Motor Filter protects the

motor from dirt particles.

It is located in the slide out tray

underneath the Dirt

Container. If the filter becomes dirty,

pull out the tray, lift

out the filter and clean.

The Post-Motor Filter assists in the

filtration process to return clean air to

the room. It is located behind the

door on the side of the cleaner. If the

filter becomes dirty, open the door,

remove the filter and clean.

Note: A white, pleated HEPA

Media Filter is offered as an

optional item. This filter is not

washable and must be replaced.

WARNING:

Do Not operate cleaner with damp or

wet filters or without all

filters in place.

The belt on your cleaner causes the

agitator to rotate and is important for

the effective operation of the

cleaner. The belt is located under

the bottom plate of the cleaner and

should be checked from time to time

to be sure it is in good condition.

Disconnect cleaner from

electrical outlet.

To check belt, remove bottom plate

as shown in “How to replace.”

Replace belt it is stretched, cut or

broken.

Remove agitator and used belt.

Discard used belt.

3-6

3-7

Insert agitator through belt and place

belt in belt guide (C) on agitator.

Should the agitator shield (D)

become dislodged while replacing

the belt or the agitator, reposition it

as shown, noting the placement of its

belt guide (D)

3-9

With lettering on outside of belt and

positioned as shown in box on (D),

slide new belt over motor pulley (B).

3-8

Disconnect cleaner from electrical

outlet.

Place handle in low position and turn

cleaner over so bottom side is up.

Remove the 4 screws as shown with

a screw driver.

3-5

Post-Motor

Filter

Pre-Motor

Filter

3-4

Note: For easier

access, the entire

Upper Tank may be

removed by turning the

knob on the back

of the cleaner to unlock

and pulling the entire

tank straight out.

Cleaning The Pre-Motor and

Post-Motor Filters

The belt

How to replace

When to replace

Maintenance

Grasp agitator firmly and fit it into

position by first sliding the end opposite

the belt into the rectangular slot (F) on

side of cleaner.

Pull other side of agitator (G) into place.

Turn agitator, making sure belt is not

pinched between agitator and agitator

shield.

3-10

Reposition bottom plate and 4

screws. Tighten screws securely.

3-11

When agitator brushes are worn,

the agitator should be replaced.

To check condition of brushes,

disconnect cleaner from

electrical outlet.

Move the edge of a card across

bottom plate while turning agitator.

To maintain cleaning effectiveness,

replace agitator if brushes do not

touch card.

Disconnect cleaner from electrical

outlet.

Remove bottom plate, belt and

agitator following directions in “The

belt” section beginning with Fig. 3-10.

Discard old agitator.

Continue following the directions in

“The belt” section to reposition belt,

new agitator and bottom plate.

3-12

Low suction or poor pickup may be

due to a clog in the vacuum

cleaner. If you notice a change in

the sound of the motor or a

reduction in the spinning action,

check for clogs.

Remove the Upper Tank and check

the suction inlet for a clog.

3-14

Empty Dirt Container.

Check Upper Tank for build up or

clogs.

3-13

Grasp the Quick Reach Handle

and lift Hose Wand to

separate from the suction opening.

Check for a clog in

the Base, the Wand or the Hose.

Remove the screw attaching the

Hose Wand Base to the

vacuum. Straighten the Hose

Wand Base and unclog

with long, narrow object.

3-15

If the clog persists, follow the

instructions for Checking

the Rotating Floor Brush on page 9

and inspect the Air

Passageway for obstructions.

3-16

WARNING:

To reduce the risk of injury from

moving parts and/ or electrical

shock, turn Power Switch OFF and

disconnect plug from electrical

outlet before performing

troubleshooting checks.

Suction Inlet

Air Passageway

Cleaning Clogs

How to replace

When to replace the

agitator brush roll

Troubleshooting

Check this list of possible problems and solutions before bringing your vacuum to a service center.

Vacuum cleaner won't run.

Possible Causes

··Power cord not firmly plugged in

··Blown fuse or breaker

Remedies

··Check electrical plug

··Check/replace fuse - Reset breaker

Vacuum cleaner won't pick up dirt.

Possible Causes

··Incorrect Height Adjustment

··Hose not attached to suction opening

··Crack or hole in Hose

Remedies

··Adjust Powerfoot to correct height setting

Grasp Quick Reach Handle and firmly push Hose

··Wand onto the suction opening

··Check Hose and replace if needed

Vacuum cleaner won't pick up dirt continued.

Possible Causes

··Broken or worn Drive Belt

··Rotating Floor Brush bristles worn

··Rotating Floor Brush jammed

··Clog in vacuum

··Dirt Container full

··Dirt Container or Upper Tank not installed

properly

··Filters are dirty

Remedies

··Replace Drive Belt, see pg. 9

··Replace brush

··Remove brush and clean debris from brush ends

··Follow instructions on pg. 10 for clearing clogs

··Empty Dirt Container

··Position correctly and lock in place

··Check and clean Upper Tank, Pre-Motor and Post-

Motor Filters

Tools won't pick up dirt.

Possible Causes

··Crack or hole in Hose

··Clog in vacuum

··Dirt Container full

··Dirt Container or Upper Tank not installed

properly

··Filters are dirty

Remedies

··Check Hose and replace if needed

··Follow instructions on pg. 10 for clearing clogs

··Empty Dirt Container

··Position correctly and lock in place

··Check and clean Upper Tank, Pre-Motor and Post-

Motor Filters

Vacuum cleaner is difficult to push.

Possible Causes

··Incorrect Height Adjustment

Remedies

··Adjust Powerfoot to correct height setting

Visible dirt escaping from cleaner.

Possible Causes

··Dirt Container full

··Filters missing or installed incorrectly

··Dirt Container installed incorrectly

If suggested solutions do not correct the problem, call:

Remedies

··Empty Dirt Container

··Check Upper Tank, Pre-Motor and Post-Motor

Filters for correct installation

··Pull out and re-insert Dirt Container correctly

Esta aspiradora cumple las siguientes directivas

de EMC: 89/336/EEC, 92/31/EEC y 93/68/EEC

Directiva sobre seguridad en aparatos de bajo voltaje: 73/23/EEC y 93/68/EEC

DJ68-00148F REV(0.2)

0870-SAMSUNG(726-7864)

Inhaltsverzeichnis

Andere Samsung Staubsauger Handbücher

Samsung

Samsung SC21K51 Series Bedienungsanleitung

Samsung

Samsung SC6560 Bedienungsanleitung

Samsung

Samsung SC20M25 Series Bedienungsanleitung

Samsung

Samsung VAC-9048R Bedienungsanleitung

Samsung

Samsung SC8700 SERIES Bedienungsanleitung

Samsung

Samsung SC07K51 Series Bedienungsanleitung

Samsung

Samsung SC5120 Bedienungsanleitung

Samsung

Samsung SC07F70 series Bedienungsanleitung

Samsung

Samsung Jet Bot VR30T80 Series Bedienungsanleitung

Samsung

Samsung SR8895 Bedienungsanleitung

Samsung

Samsung VS15A60 Series Bedienungsanleitung

Samsung

Samsung VC-8828E Bedienungsanleitung

Samsung

Samsung Perfectum SC7355 Bedienungsanleitung

Samsung

Samsung SC15F30 Series Bedienungsanleitung

Samsung

Samsung SC07F60 Series Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung VC- W113 Bedienungsanleitung

Samsung

Samsung POWERbot SR2AK9350W Series Bedienungsanleitung

Samsung

Samsung VC-7726V Bedienungsanleitung

Samsung

Samsung SC4770 User Manual (Windows 7) Bedienungsanleitung

Samsung

Samsung POWERbot SR20J90 U Series Bedienungsanleitung

Samsung

Samsung SC4751 User Manual (Windows 7) Bedienungsanleitung

Samsung

Samsung SC07M21 Series Bedienungsanleitung

Samsung

Samsung SC88 series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung