Sanus Systems VisionMount VMAA26 Bedienungsanleitung

Assembly Instructions for Model: VMAA26

Thank you for choosing a Sanus Systems VisionMount™ wall mount. The VMAA26 is designed to mount up to 50” Flat panel televisions

weighing up to 130 lb. to a vertical wall. It allows you to tilt the television from +5° to -15°. It will also extend 25.75” away from the wall,

swivel up to 180°, and roll ± 6°.

CAUTION: The size and weight of your television must not exceed 50” [1270 mm] diagonally and 130 Lbs [59 Kg]. The wall

must be capable of supporting ve times the weight of the television plus the wall mount. Never use defective parts. Improper

installation may cause property damage or personal injury. Do not use this product for any purpose that is not explicitly

specied by Sanus Systems.

If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualied contractor

or contact Sanus at 800.359.5520 or www.sanus.com. Our customer service representatives can quickly assist you with installation

questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly

to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury

caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of

purchase.

NOTE: This mount is not intended for use on brick, concrete block, concrete, or steel wall studs. Typical wall anchors do not

have sufcient holding power to support this mount. It is up to the installer to verify the safety of any installation method or

hardware that is not provided by or recommended by Sanus Systems. Sanus Systems makes every effort to assure all necessary

television mounting hardware is included. If the television mounting hardware you need is not included please consult your

local hardware store or call Sanus Systems

Required Tools: 3/16” drill bit, drill, adjustable or crescent wrench, Phillips screwdriver.

Supplied Parts: (Some parts are not shown at same scale)

Wall Plate - A

Qty. 1

I” Diameter Tube - D

Qty. 2

Preventor - C

Qty. 1

Arm Assembly - B

Qty. 1

Vise Assembly - F

Qty. 4

Monitor Bracket - E

Qty. 2

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 09.26.06 (6901-100017)

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Hardware: (Hardware shown is actual size)

Wire Tie Clip - G

Qty. 7

Wire Tie - H

Qty. 10

7/32 & 3/16 Allen Keys - K

Qty. 1 Each

Lag Bolt Washer - J

Qty. 4

Lag Bolt - I

Qty. 4

Safety Bolt - N

Qty. 3

Preventor Bolt - O

Qty. 2

1/4-20 Nut - M

Qty. 4

2” Carriage Bolt - L

Qty. 4

Supplied Television Mounting Hardware: (Hardware shown is actual size)

M8 x 16 mm Bolt - S

Qty. 4

M4 x 12 mm Bolt - P

Qty. 4

M5 x 12 mm Bolt - Q

Qty. 4 M6 x 12 mm Bolt - R

Qty. 4

LM8 x 30 mm Bolt - W

Qty. 4

M4 x 30 mm Bolt - T

Qty. 4 M5 x 30 mm Bolt - U

Qty. 4

M6 x 35 mm Bolt - V

Qty. 4

M8 Lock Washer - AA

Qty. 4

M4 Lock Washer - X

Qty. 4 M5 Lock Washer - Y

Qty. 4

M6 Lock Washer - Z

Qty. 4

M6/M8 Washer - EE

Qty. 4

M4/M5 Spacer - BB

Qty. 4 M/M8 Spacer - CC

Qty. 4

M4/M5 Washer - DD

Qty. 8

Step 1: Mounting Monitor Brackets to a Televisions with a at back

NOTE: For TVs with a curved back or any other obstruction See Step 2. After completing this step, proceed to Step 3.

Determine the diameter of the Bolt (P,Q,R,S) your TV requires by hand threading them into the threaded insert on the back of the

TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, refer to the appropriate

Diagram below. Thread the Bolt through the appropriate Lock Washer (X,Y,Z,AA), a Washer (DD,EE), the Monitor Bracket (E) and

nally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. Repeat this process until each

Monitor Bracket is secured to the TV with two bolts.

M4 Diameter Bolt

M8 Diameter Bolt

M5 Diameter Bolt

M6 Diameter Bolt

Diagram 1

Step 2: Mounting the Monitor Brackets to Televisions with a curved back or other obstruction.

Determine the diameter of the Bolt (T,U,V,W) your TV requires, by hand threading them into the threaded insert on the back of the

TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, refer to the appropriate

Diagram below. Thread the Bolt through the appropriate Lock Washer (X,Y,Z,AA), a Washer (DD,EE), the Monitor Bracket (E),

a second Washer (DD - M4/M5 diameter only), a Spacer (BB,CC), and nally into the TV. Make sure the Monitor Brackets are

vertically centered and level with each other. Repeat the process until each Monitor Bracket is secured to the TV with two bolts.

CC E

M4 Diameter Bolt

M8 Diameter Bolt

M5 Diameter Bolt

M6 Diameter Bolt

Diagram 2

Step 3: Add the Vise Assemblies to the Monitor Brackets:

NOTE: Do not overtighten the 1/4-20 Nut (M). The Vise Assembly (F) should be able to rotate freely around the

Carriage Bolt (L).

Place the Vise Assembly (F) into the Monitor Bracket (E) so that the two Jaws point toward the set of 1” diameter holes

and the Allen Bolt is facing away from the television. Place a 2” Carriage Bolt (L) through the square hole in the side of the

Monitor Bracket, and the Vise Assembly; then, through the square hole in the other side of the Monitor Bracket. Thread and

tighten a 1/4-20 Nut (M) onto the end of the 2” Carriage bolt. Repeat this step for the bottom of the Monitor Bracket; then,

repeat this process for the second Monitor Bracket. See Diagram 3 and Vise Detail.

Vise Detail

Diagram 3

Step 4: Attach the Arm Assembly to the Television

Align each Vise Assembly (F) so that a 1” Diameter Tube (D) will pass through the 1” round hole in the Monitor Bracket (E)

and between the jaws of the Vise Assembly. Insert a 1” Diameter Tube through the top hole in the rst Monitor Bracket.

Repeat this step for the Bottom hole in the same Monitor Bracket. See Diagram 4a for assistance.

Diagram 4a

Jaws

1” Dia.

Hole

Allen

Bolt

Step 4: Attach the Arm Assembly to the Television (Continued on next page.)

Step 4: Attach the Arm Assembly to the Television (Continued)

CAUTION: The 1” Diameter Tubes (D) must extend beyond the outside edges of both Monitor Brackets (E) and

the Allen Bolts in all 6 Vise Assemblies (F) must be tightened. Failure to do this will result in an installation that

unstable and may result in property damage and/or personal injury.

Position the Arm Assembly (B) so the hook shaped tab shown in Detail View of Diagram 4b is on the top. Line up the two

1” diameter holes in the Monitor Bracket (E) at the other end of the Arm Assembly with the with the 1” Diameter Tubes

(D). Push the 1” Diameter Tubes through the bracket on the Arm Assembly; then, through the other Monitor Bracket.

Make sure the Vise Assemblies (F) on both the Arm Assembly and the second Monitor Bracket are aligned so that the

1” Diameter Tubes will pass between the jaws.

NOTE: Do not over-tighten the Vise Assembly (F), or the Vise Assemblies in the Arm Assembly (B). When tightening

the Vise Assemblies, turn the Allen Bolt in until resistance is felt; then, tighten the Allen Bolt approximately 1 & 1/2

turns or until the head of the Allen Bolt is slightly above the surface of the Vise Assembly. The 1” Diameter Tubes

(D) must not be able to move from side-to-side when the Vise Assembly is properly tightened.

Once the 1” Diameter Tubes are in place, tighten the allen bolts on the 4 Vise Assemblies in the two Monitor Brackets with

the 3/16 Allen Key (K) to lock the television to the mount. Slide the Arm Assembly into the desired position between the

two Monitor Brackets (Sanus recommends Arm Assembly be centered between the Monitor Brackets) and tighten the two

remaining Allen Bolts in the Vise Assemblies inside the Arm Assembly.

Detail View

Diagram 4b

Step 5: Attach the Wall Plate: Wood Stud installation only.

CAUTION: Do not overtighten the Lag Bolts. Tighten Lag Bolts (I) only until the Lag Bolt Washer (J) is pulled

rmly against the Wall Plate (A). If there is a layer of drywall or other material, this drywall or other material may not

exceed 5/8 inch [15.8 mm] in thickness. Failure to heed this caution may result in property damage and/or personal

injury.

Tab

The Wall Plate (A) must be mounted to two wood studs at

least 12” apart. Use a high quality stud sensor to locate two

adjacent studs. Verify where the studs are located with an

awl or thin nail. Pre-drill a 2.5” deep hole in each stud at

the desired height using a 3/16” drill bit. Make sure these

holes are in the center area of the studs and level with

each other. Use the Wall Plate as a template to mark the

location of the second hole in each stud. Drill 2.5” deep

holes using the 3/16” drill bit in the marked location. Attach

the Wall Plate to the wall using four Lag Bolts (I) and four

Lag Bolt Washers (J). Make sure the Wall Plate is oriented

so the at surface in the center of the plate is against the

wall. See Diagram 5 for assistance.

Stud

Drywall cut away

to show studs.

Diagram 5

Step 7: Leveling the Monitor and Adjusting the Tension

CAUTION: Do not remove the Tension Nuts in Diagram 7. Removing Tension Nuts will result in property damage.

Once the television is mounted onto the Wall Plate (A), and the Safety Bolts (N) are tight, it can be adjusted to level. Slightly loosen

the two Allen Bolts on the back of the Arm Assembly (B). Once the Allen Bolts are loosened, the television can be adjusted ±6º until

level. When the television is level retighten the two Allen Bolts. The tilt can be adjusted by setting the tension of the Tension Knobs

and tilting the television. The Tension Nuts labeled in Diagram 7 can be slightly loosened or tightened using the 7/32 Allen Key (K)

and wrench to adjust the tension of the Arm Assembly. If you need to adjust the Tension Nut closest to the TV, you must remove

the Safety Bracket, adjust the tension and re-install the Safety Bracket as shown in Safety Bracket Installation.

Safety Bracket Installation

Diagram 7

Step 6: Hang the assembly onto the Wall Plate

CAUTION: This step may require two people to lift the assembly onto the Wall Plate. Sanus is not responsible for

property damage and/or personal injury.

Orient the Arm Assembly (B) so the arm extends directly away from the television and the Transfer Plate is parallel with the

television. Lift the assembly and hook the Transfer Plate onto the tab on the top of the Wall Plate (A) as shown in Diagram

6a. Horizontally adjust the Transfer Plate side to side on the Wall Plate until it is in the desired location.

CAUTION: make sure the Saftey Bolt (N) is tight. A loose Safety Bolt will result in an unstable installation which

may result in property damage and/or personal injury.

Thread each Safety Bolt (N) into one of the three holes in the bottom of the Transfer Plate and tighten them so that they are

behind the Tab on the bottom of the Wall Plate as shown in Diagram 6b.

Diagram 6a Diagram 6b

Transfer Plate

Tab

Tension

Knob

Tension

Nut

Tension

Nut

Allen

Bolt

Safety

Bracket

Step 8: Add Preventor

CAUTION: Avoid Pinch Points. Placing your hands or ngers between moveable parts (Pinch Points) may result

in personal injury

Determine which direction you want the Arm to fold. If you want the Arm to fold to the right, place the Preventor (C) on the

right side of the Arm Assembly (B). If you want the Arm to fold to the left, place the Preventor on the left side of the Arm

Assembly. Position the Preventor so the at side is facing the Idler as shown in the Detailed View of Diagram 8. To attach

the Preventor, place a Preventor Bolt (O) through the Preventor and into the holes in the Idler. Tighten the Preventor Bolts

with an Allen Key (K).

Diagram 8 Detail View

Step 9: Cable Management

CAUTION: Do not run Cables through a Pinch Point. Running Cables through Pinch Points may result in damage

to the Cables.

Before beginning cable management pull the television into the position as far from the wall as possible. Leave some slack

in the cables so that during motion so there is no added tension on the connectors. There are several places to attach Wire

management ties to keep cables out of the way. Wire Tie Clips (G) can be attached to the holes in the top and the bottom

of the Arm Assembly (B), sides of the Preventor (C) and the top and bottom of the pillow block by simply pressing them into

place as shown in the Detailed View of Diagram 9. Wire Ties (H) can then be added to both the Wire Tie Clips, or the holes

in the sides of either of the Monitor Brackets (E).

Diagram 9 Detail view

CSAV, Inc. and its afliated corporations and subsidiaries (collectively, “CSAV”), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein

covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to

change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy,

completeness or sufciency of the information contained in this document.

Idler

Andere Handbücher für VisionMount VMAA26

Andere Sanus Systems Rack & Stand Handbücher

Sanus Systems

Sanus Systems HTSAT Bedienungsanleitung

Sanus Systems

Sanus Systems VMCT Bedienungsanleitung

Sanus Systems

Sanus Systems Euro Series Bedienungsanleitung

Sanus Systems

Sanus Systems NF18B Bedienungsanleitung

Sanus Systems

Sanus Systems Monitor Mount VMTV Bedienungsanleitung

Sanus Systems

Sanus Systems Platinum Furniture PFV36sb-01 Bedienungsanleitung

Sanus Systems

Sanus Systems EFSat Bedienungsanleitung

Sanus Systems

Sanus Systems Sanus VisionMount LC1A Bedienungsanleitung

Sanus Systems

Sanus Systems Sanus VisionMount VMAA18 Bedienungsanleitung

Sanus Systems

Sanus Systems VMCA9 Bedienungsanleitung

Sanus Systems

Sanus Systems VMFL1 Bedienungsanleitung

Sanus Systems

Sanus Systems VMCM1 Bedienungsanleitung

Sanus Systems

Sanus Systems PFV60-B1 Bedienungsanleitung

Sanus Systems

Sanus Systems SD103 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount VMPL2 Bedienungsanleitung

Sanus Systems

Sanus Systems VMPL50 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount MF203 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount ML22 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount MF202 Bedienungsanleitung

Sanus Systems

Sanus Systems VMPL50 Bedienungsanleitung

Sanus Systems

Sanus Systems VMCC1 Installationsanleitung

Sanus Systems

Sanus Systems VMFL1 Bedienungsanleitung

Sanus Systems

Sanus Systems VM2 Bedienungsanleitung

Sanus Systems

Sanus Systems PFFP Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung