Sanyo VCC-6592P Bedienungsanleitung

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

VCC-6592P

VCC-6594P

COLOUR CCD camera

CCD-Farbkamera

Caméra CCD COULEUR

CCD

About this manual

• Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

• This manual gives basic connections and operating instructions for 2

PAL models (VCC-6592P, 6594P).

Über diese Bedienungsanleitung

• Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera

zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie

sie zum späteren Nachschlagen auf.

• In dieser Anleitung finden Sie die Anschlüsse und die Grundbedienung

für 2 PAL-Modelle (VCC-6592P und 6594P)

A propos de ce manuel

• Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel

attentivement. Gardez-le à portée de main pour toute référence

ultérieure.

• Ce manuel couvre les branchements et instructions pour l’utilisation

de base pour 2 modèles de format PAL (VCC-6592P et 6594P).

2PAL VCC-6592P, 6594P

L53H2, H4/XE GB 2001, 9, 18

1AC6P1P2424--

L53H2, H4/XE (0901KPS-DSP)

Sanyo Electric Co, Ltd.

Printed in Japan

L53H2, H4/XE GB 2001, 9, 18

Depending on the conditions of use, installation and environment,

please be sure to make the appropriate settings and adjustments. If you

need help with installation and/or settings, please consult your dealer.

CONTENTS

PRECAUTIONS........................................................................................ 2

PARTS NAMES........................................................................................3

CONCERNING AUTO-IRIS LENSES......................................................... 6

MOUNTING THE LENS........................................................................... 7

CONNECTIONS....................................................................................... 9

SETTINGS................................................................................................12

TROUBLESHOOTING..............................................................................18

SPECIFICATIONS.....................................................................................19

ACCESSORIES

1Lens iris plug ( -pin)..................................................................1 pc.

2Clamping core A: VCC-659 P...................................................2 pc.

VCC-6592P...................................................3 pc.

3Clamping core B: VCC-659 P...................................................1 pc.

VCC-6592P...................................................2 pc.

123

FEATURES

•Built-in interline transfer method 1/3" CCD, approx. 70,000

picture elements

•Equipped with a DSP (Digital Signal Processor) function

•Horizontal resolution, more than 520 TV lines

•High sensitivity, minimum required illumination is 0.3 lux (F1.2,

AGC HI position)

•Two types of backlight compensation functions (multi-spot

photometry and center focus photometry)

•Low smear, anti-blooming, low lag, no burning and no geometric

distortion using the CCD solid state image device.

•100% solid state components giving excellent immunity to shock

and vibration

•Not subject to interference from magnetic or electrostatic fields

•Power supply: 2 V AC operation (VCC-659 P)

12 V DC operation (VCC-6592P)

L53H2, H /XE GB 2001, 9, 18

English 1

RECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the

unit, or if it seems not to function correctly. Disconnect the power

cord immediately, and consult your dealer (or a Sanyo Authorized

Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage

to the unit. For internal settings and repairs, consult your dealer (or a

Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside

the camera. If used with a foreign object inside, it could cause a fire,

short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord

immediately, and consult your dealer (or a Sanyo Authorized Service

Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong

shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

rotect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high, or

where there is a lot of dust.

rotect from high temperatures

Do not install close to stoves, or other heat generating devices, such

as spotlights, etc., or where it could be subject to direct sunlight, as

that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler

room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10˚C and

50˚C.

(no condensation)

Cleaning

•Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with a

soft detergent solution and wrung dry, then wipe dry with dry

soft cloth.

•Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling.

Before using a chemical cloth, make sure to read all

accompanying instructions. Make sure that no plastic or rubber

material comes in contact with the cabinet for a long period of

time, as that may cause damage or paint peeling.

ENGLISH

L53H2, H /XE GB 2001, 9, 18

2 English

ARTS NAMES

1Video output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

2ower input terminal

•VCC-6592P: 12 V DC input terminal (12 V DC, GND)

•VCC-659 P: 2 V AC input terminal (AC 2 V, AC 2 V, GND)

3Y/C OUT connector (4 pin)

Separate Y (luminance) and C (chroma) signals are output from this terminal.

A better picture quality is obtained if the monitor or VCR is connected to this connector.

1Y signal ground 2C signal ground

3Y signal: 1.0 Vp-p, 75 ohms, unbalanced, negative sync

4C signal: 0.3 Vp-p, 75 ohms, unbalanced

4ower indicator ( OWER)

Comes on when the power to the camera is on.

5External sync composite video signal input connector

(VBS IN: BNC type)

Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite

signal of a video distributor.

6Line phase adjustment volume (LINE HASE) (VCC-6594 only)

When using two cameras or more, the image on the monitor may roll vertically when switching sources. This

rolling can be minimized by turning this volume.

(VCC-6594P)

(VCC-6592P)

L53H2, H /XE GB 2001, 9, 18

English 3

ARTS NAMES

7Lens mount cap

The cap is installed to protect the lens mount section.

Remove the lens mount cap before installing a lens (sold separately).

8Flange-back adjustment screw (FLANGE BACK ADJ.)

9Flange-back lock screw (FLANGE BACK LOCK)

FCamera installation bracket

The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the

longer screws and install the shorter screws on the opposite side to seal the openings.

CAUTION:

When installing the camera support, select a location that can support the total weight of the

camera and accessories.

1Shorter screws: M3 x 4

2Longer screws: M3 x 6

3Camera mounting screw

hole: 1/4"-20 UNC

1232

L53H2, H /XE GB 2001, 9, 18

4 English

ARTS NAMES

GLens iris output connector (LENS)

This -pin connector is used to send the DC control signal and power supply to an auto-iris type lens.

HCamera setup section (under the cover)

These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However,

if due to installation conditions or environment the settings may need to be modified for best results (see

"SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover.

NOTE: When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the

A.I. LENS switch to the VIDEO position.

L53H2, H /XE GB 2001, 9, 18

English 5

CONCERNING AUTO-IRIS LENSES

DC type auto-iris lens

A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is

referred to as DC type coil lens or DC type non-amplifier lens.

(Set the A.I. LENS switch to the DC position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is

referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments.

(Set the A.I. LENS switch to the VIDEO position.)

Compatible auto-iris lenses

1/3 inch Sanyo DC type lens VIDEO type lens

VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm

VCL-CS LY: Wide angle, f= mm Telephoto angle, f= 12 mm

VCL-CS2LY: Ultra-wide angle, f= 2.8 mm Greater telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

•Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned

all the way to Av (Average).

•Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL

volume on the lens casing to correct.

VIDEO

A. I.

LENS

VR301

L53H2, H /XE GB 2001, 9, 18

6 English

MOUNTING THE LENS

Please se a DC type a to-iris lens (sold separately).

Check the lens mount

Do not use a lens if the length “L” is more than 5 mm. That may damage the

camera and prevent proper installation.

1Remove the lens mount cap from the camera.

2Install the auto-iris lens.

CS mount type lens

Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.

C mount type lens

To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully

align the lens mount with the camera opening and turn the lens slowly to install it.

3Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.

When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.

In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug

according to the diagram. (Refer to page 8.)

NOTE: When using an auto-iris lens, the supplied clamping core B must be installed on the lens wire, in

order to prevent electromagnetic interference to the other devices connected.

C mount type lens

CS mount

type lens

L53H2, H /XE GB 2001, 9, 18

English 7

MOUNTING THE LENS

Rewiring the lens cable in the lens iris pl g

1repare the lens cable.

Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.

2Install the lens iris plug.

Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close

the plug cover.

in layout

DC type lenses VIDEO type lenses

1Brake coil (–) +12 V DC (50 mA max.)

2Brake coil (+) Not used

3Drive coil (+) Video output (1.0 Vp-p, high impedance)

4Drive coil (–) Ground (for video signal and DC power)

Flange-back adj stment

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of

focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the

flange-back position as described below.

1Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+).

2Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.

3Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. screw.

4Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.

When the setting is complete, tighten the FLANGE BACK LOCK screw.

2, 3

LOCK

ADJ.

L53H2, H /XE GB 2001, 9, 18

8 English

Andere Handbücher für VCC-6592P

Dieses Handbuch passt für folgende Modelle

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCB-3512T Bedienungsanleitung

Sanyo

Sanyo VCC-9500P Bedienungsanleitung

Sanyo

Sanyo VCC-W9875VP Bedienungsanleitung

Sanyo

Sanyo vcb-3400p Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-4794E - 1/3" Color CCD DSP Day/Night... Bedienungsanleitung

Sanyo

Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584 - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

Sanyo

Sanyo VCC-6592PC Bedienungsanleitung

Sanyo

Sanyo VCC-HD2300P Bauanleitung

Sanyo

Sanyo VCC-5972P Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-6584 Bedienungsanleitung

Sanyo

Sanyo VCC-9800 Bedienungsanleitung

Sanyo

Sanyo VCC-ZM600 Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584N - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-XZN600P Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100P Bedienungsanleitung

Sanyo

Sanyo VDC-HD3100 - Full HD 1080p Vandal Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-6585P Bedienungsanleitung

Sanyo

Sanyo VCC-3944 - 1/4" Color CCD DSP Camera Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600P Series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung