Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

SUMMARY MANUAL

Side A

Megapixel Camera

VCC-HD2500P/HD2500

VCC-HD2300P/HD2300

VCC-HD2100P/HD2100

THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED

SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL

CODES.

Please read this instruction manual carefully in order to ensure correct installation.

In addition, be sure to read carefully the electronic manual (INSTRUCTION MANUAL)

contained in the supplied CD-ROM to ensure correct operation of the camera.

EnglishFrançaisEspañolDeutschЁ᭛ㅔԧ日本語

L5DB2HD2500PSMGB.indd1L5DB2HD2500PSMGB.indd1 2009/09/0820:45:312009/09/0820:45:31

Table of Contents

Name and Function of Each Component .................................................................2

Basic Connections.................................................................................................... 5

Alarm Terminal Connections..................................................................................... 6

Lens Adjustment....................................................................................................... 7

Network Settings .................................................................................................... 10

Specifications ......................................................................................................... 11

Check your operating environment.

To operate the camera via network operation, you must meet the following operating

requirements.

•: IBM PC/AT compatible

Operating system

•: Windows XP Professional/Windows Vista

CPU

•: Core2Duo E6700 2.66 GHz or higher

Memory

•: Windows XP: 1GB or more

Windows Vista: 2GB or more

Network interface

•: 10Base-T/100Base-TX (RJ-45 connector)

Display card

•: 1920×1200 pixels or higher

Graphics chip

•: ATI RADEON HD2600 series or higher

nVIDIA GeForce 8600 series or higher

nVIDIA Quadro FX550 series or higher

Web browser

•: Internet Explorer Ver. 6.0 SP2 or higher,

or Internet Explorer Ver. 7.0

■

You can automatically set up the IP address of the camera.

This software application is useful when two or more cameras are connected to the

network.

Download “AUTO IP SETUP” software application from the supplied CD-ROM.

■

Accessories

①Video Cable

②Cable holder for wiring

③CD-ROM

④Clamping Core

To prevent electromagnetic interference

VCC-HD2500P VCC-HD2300P

VCC-HD2100P

■

L5DB2HD2500PSMGB.inddSec1:1L5DB2HD2500PSMGB.inddSec1:1 2009/09/0820:45:322009/09/0820:45:32

Name and Function of Each Component

Rear Face

AUDIO

DC12V

CLASS 2

WIRING

②⑤

⑧

⑦

⑥

③

④

①

①SD (SDHC) Card Slot (VCC-HD2500P/HD2500)

②Audio Output Jack (AUDIO OUT, 3.5-mm mini jack) (VCC-HD2500P/HD2500)

③Power Indicator (POWER)

The power indicator blinks to indicate the following camera statuses.

Recording to SD memory card stopped/camera is recognizing SD memory card/

An error occurred

Firmware update in progress

④Power Terminals (24 V AC/12 V DC)

⑤Audio Input Jack (AUDIO IN, 3.5-mm mini jack) (VCC-HD2500P/HD2500)

⑥Network Socket (LAN, RJ-45)

Ⓐ Ⓑ

ⒶAccess indicator

Lights: Connection has been established between the camera

and the network.

•

Blinks: Data are being transmitted via the network.•

ⒷSpeed indicator

Lit: 100BASE-TX

•

Unlit: 10BASE-T•

⑦Control Terminals (ALARM IN/OUT: 6 push-lock pins)

These terminals can be used as alarm input or Day/Night switching terminals.

⑧Monitor Output Socket (MONITOR OUT)

■

•

L5DB2HD2500PSMGB.inddSec1:2L5DB2HD2500PSMGB.inddSec1:2 2009/09/0820:45:322009/09/0820:45:32

Side Face

NEAR

FAR

SET

RESET

①

②③

①Operation Buttons

Restarting camera: Press the RESET button.

OPTION SETTINGS (CAMERA REBOOT)

Stopping recording/Removing SD memory card: Press the NEAR button for

2 seconds or more.

The power indicator starts blinking and then stays lit when the camera is ready for

you to remove the SD memory card.

SD MEMORY CARD

Resuming stopped recording/Having camera recognize SD memory card:

Press the FAR button for 2 seconds or more.

The power indicator starts blinking and then stays lit when the camera has

recognized the SD memory card.

Restoring factory default settings: Press the NEAR and SET buttons

simultaneously.

OPTION SETTINGS (FACTORY DEFULT)

Resetting login password (for default users only): Press the FAR and SET

buttons simultaneously.

Restoring factory default back focus position: Press the NEAR and FAR

buttons simultaneously.

CAMERA SETTING (FOCUS ASSIST)

Adjusting focus/Adjusting iris

Page 7, “Lens Adjustment” section or the CAMERA SETTINGS (FOCUS

ASSIST/IRIS SETTING) section on the electronic manual.

Viewing Firmware Version:

“Viewing Firmware Version” section or the OPTION SETTINGS (FIRMWARE

UPDATE) section on the electronic manual.

SD memory card: SD card

■

•

Name and Function of Each Component

L5DB2HD2500PSMGB.inddSec1:3L5DB2HD2500PSMGB.inddSec1:3 2009/09/0820:45:322009/09/0820:45:32

Name and Function of Each Component

②Auto Iris Lens Socket (LENS)

Connect the lens cable plug to the auto iris lens socket provided on the left-side face of

the camera.

It is recommended that you use a CS-mount DC auto iris megapixel lens (commercially

available).

LENS terminal for auto iris lens

Brake coil (+)

Drive coil (–)

Brake coil (–)

Drive coil (+)

5 mm max.

Keep the lens clean at all times.

The conversion ring (commercially available) is required to use a C-mount

lens.

The lens cable plug must be changed if it does not fit into the auto iris

lens socket. If so, contact the distributor from which you purchased the

product (or the agent that provides the installation service).

③Bracket

This bracket may be attached to either the top or bottom face of the camera as shown

in the figure.

When you install the camera, make sure that the screws can securely fix the camera to

the bracket.

Install the camera mount (commercially available) securely to a durable

location, taking into account the total weight of the camera mount and the

camera.

L5DB2HD2500PSMGB.inddSec1:4L5DB2HD2500PSMGB.inddSec1:4 2009/09/0820:45:332009/09/0820:45:33

Basic Connections

AUDIO

DC12V

CLASS2

WIRING

LAN

OUTIN

COM

ALARM

POWER

AC24V

GND

AC24V

GND

AC24V

GND

VCC-HD2500P

VCC-HD2300P

VCC-HD2100P

①

②

③

Ⓐ24 V AC

Ⓑ12 V DC

Power supply

Monitor

VCC-HD2500P

VCC-HD2500

24 V AC

12 V DC

①Power Connection

Connect the power terminals (24 V AC/12 V DC) of the camera to a power supply.

ⒶConnection to 24 V AC power supply

Although the power terminals have no polarity, the earth grounding wire must be

connected to the GND (earth grounding) terminal.

ⒷConnection to 12 V DC power supply

Note the polarity (+/–) of the power terminals when connecting the camera to a

12 V DC power supply.

Incorrect polarity may cause damage to the camera.

Be sure to use an 18AWG or thicker wire power cable.

If you want to use PoE to supply power, do not connect to AC/DC power

supply.

•

②Network Connection

This camera is designed so that you can use all of its functions via network

operation.

By connecting the network (LAN) socket of the camera to your PC using a LAN

cable, you can configure and operate it from the Web browser installed on your PC.

③Camera Monitor Connection (“Lens Adjustment” Page 7)

A monitor can be connected to perform focus adjustment with the camera.

Connect the monitor output socket (MONITOR OUT) of the camera to a monitor via

the monitor cable. After adjustment, be sure to remove the monitor cable.

L5DB2HD2500PSMGB.inddSec1:5L5DB2HD2500PSMGB.inddSec1:5 2009/09/0820:45:332009/09/0820:45:33

To connect a cable, while pushing the protrusion of the terminal, insert the cable into

the opening and then release it.

External

peripheral

device

Alarm input

signal

Alarm input

signal

(COM)

(ALARM OUT 1)

(ALARM OUT 2)

(ALARM IN 1)

(ALARM IN 2)

󱤨

󱤩

󱤨Alarm Output Terminal Connection

Connect a buzzer, lamp, or other alarm device to one of the alarm output terminals

(ALARM OUT 1 or 2).

After connecting an alarm device, configure the output conditions

for the corresponding alarm output terminal (ALARM OUT 1 or 2) via

network operation on the ALARM SETTINGS screen.

Alarm output terminal configuration is also possible via remote

operation.

•

󱤩Alarm Input Terminal Connection

Connect an alarm switch, infrared sensor, or other external device to one of the

alarm input terminals (ALARM IN 1 or 2).

After connecting an alarm device, configure the input conditions for

the corresponding alarm input terminal (ALARM IN 1 or 2) via network

operation on the ALARM SETTINGS screen.

VCC-HD2500P/HD2500/HD2300P/HD2300:

To use the alarm input terminals as Day/Night switching terminals, follow

the steps below.

Under [DAY/NIGHT], set [DAY/NIGHT] to “COLOR” and select the

terminal you want to use in [EXT ALARM].

On the ALARM SETTINGS screen, in [POLARITY], select the signal

polarity of the alarm input terminal.

•

Alarm Terminal Connections

L5DB2HD2500PSMGB.inddSec1:6L5DB2HD2500PSMGB.inddSec1:6 2009/09/0820:45:332009/09/0820:45:33

Lens Adjustment

For high-resolution megapixel images, the focus assist function is useful to obtain a

precise focus because otherwise it is extremely difficult.

If you are using a varifocal lens, adjust the focus using the following procedure.

If the focus assist function does not work properly because the camera

produces too dark or too bright video images, perform iris adjustment in

advance.

󱳛Press the SET button for 2 seconds or more.

The monitor now shows the SELECT MENU screen.

NEAR FAR

SET

RESET

󱳛

󱳝

SELECT MENU

FOCUS ASSIST

IRIS

FIRMWARE VERSION

NEAR UP

FAR DOWN

SET SELECT

On the SELECT MENU screen, all information is displayed in English.

󱳝Select [FOCUS ASSIST] using the NEAR/FAR button and press the SET

button.

The monitor now shows the focus adjustment screen.

󱳟Use the zoom lever of the lens to adjust the angle of view and the focus

lever of the lens to set the FA bar 󱤨to the maximum level.

When the subject comes into focus, the color of the status indicator 󱤩

“FOCUSING” turns from black to orange.

If the use of the focus lever does not provide precise focusing, follow the “Fine-

adjusting focus” procedure on the next page.

FOCUSING

PEAK HOLD XXXX

INDICATOR XXXX

NEAR FAR

FOCUSING

PEAK HOLD XXXX

INDICATOR XXXX

NEAR FAR

󱤩

󱤨

󱤪

PEAK HOLD: Shows the value of the maximum focus level.

INDICATOR: Shows the value of the current focus level.

L5DB2HD2500PSMGB.inddSec1:7L5DB2HD2500PSMGB.inddSec1:7 2009/09/0820:45:342009/09/0820:45:34

Lens Adjustment

Fine-adjusting focus (using buttons provided on side face)

󱳝

󱳟

NEAR FAR

SET

RESET

󱳛Use the zoom lever of the lens to adjust the angle of view and the focus

lever of the lens to roughly focus on the subject.

󱳝Press the SET button. (Focus adjustment screen Page 7)

The camera automatically focuses on the subject. Note that the color of the status

indicator 󱤩“FOCUSING” turns from black to orange.

If the camera failes to focus on the subject, the FA bar 󱤨will not operate normally

with the status indicator 󱤩showing “ERROR”. In this case, manually adjust the

focus. ( Electronic manual)

󱳟Press the NEAR/FAR button to adjust the focus.

Pressing the button causes the back focus position to change, which is indicated

in the FB bar gauge 󱤪.

The position changes step by step each time the button is pressed and

continuously at a high speed when the button is held down.

If you want to restore the default back focus position in re-

adjustment, etc., press the NEAR and FAR buttons simultaneously.

While the camera is initializing the back focus position, the status

indicator 󱤩shows “INITIALIZING”.

󱳡Press the SET button for 2 seconds or more.

The focus adjustment screen will close and the SELECT MENU screen reappears.

The focus adjustment screen will also close automatically if left idle

for 5 minutes or more.

VCC-HD2500P/HD2500/HD2300P/HD2300:

Adjust the focus using the following procedure when the camera

fails to focus on the subject in color or black-and-white mode.

①Select [FOCUS ASSIST] on the CAMERA SETTINGS screen and

make sure that “AUTO” is set for [COLOR/B/W].

②Adjust the focus in color or black-and-white mode.

•

■

L5DB2HD2500PSMGB.inddSec1:8L5DB2HD2500PSMGB.inddSec1:8 2009/09/0820:45:352009/09/0820:45:35

Adjusting iris

If the camera produces too dark, too bright, or other incorrect video images, adjust the

lens iris.

󱳛Press the SET button for 2 seconds or more.

The monitor now shows the SELECT MENU screen.

NEAR

FAR SET

SELECT MENU

FOCUS ASSIST

IRIS

FIRMWARE VERSION

NEAR UP

FAR DOWN

SET SELECT

󱳛

󱳝

On the SELECT MENU screen, all information is displayed in English.

󱳝Select [IRIS] using the NEAR/FAR button and press the SET button.

The monitor now shows the iris adjustment screen.

IRIS

LEVEL

DARK LIGHT

------ú--------40

NEAR LEFT

FAR RIGHT

IRIS

LEVEL

DARK LIGHT

------ú--------40

NEAR LEFT

FAR RIGHT

NEAR

FAR SET

󱳟Press the NEAR/FAR button to adjust the iris level.

The position changes step by step each time the button is pressed and

continuously at a high speed when the button is held down.

NEAR: Closes the iris to produce darker images.

FAR: Opens the iris to produce brighter images.

•

󱳡Press the SET button for 2 seconds or more.

The iris adjustment screen will be closed.

The iris adjustment screen will also close automatically if left idle for

5 minutes or more.

■

Lens Adjustment

L5DB2HD2500PSMGB.inddSec1:9L5DB2HD2500PSMGB.inddSec1:9 2009/09/0820:45:352009/09/0820:45:35

Andere Handbücher für VCC-HD2100 - Full HD 1080p Network Camera

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCC-ZM300A Bedienungsanleitung

Sanyo

Sanyo VCC-4790P Bedienungsanleitung

Sanyo

Sanyo VCC-XZ400P Bedienungsanleitung

Sanyo

Sanyo VCC-9784VA Bedienungsanleitung

Sanyo

Sanyo VCC-WB4000P Bedienungsanleitung

Sanyo

Sanyo VDC-D1785IRVP Bedienungsanleitung

Sanyo

Sanyo VCB-3385P Bedienungsanleitung

Sanyo

Sanyo VCC-3924P Bedienungsanleitung

Sanyo

Sanyo VCB-3444 Bedienungsanleitung

Sanyo

Sanyo VDC-D1184VA Bedienungsanleitung

Sanyo

Sanyo VCC-4312P Bedienungsanleitung

Sanyo

Sanyo VCC-XZN600P Bedienungsanleitung

Sanyo

Sanyo VCC-6594 Bedienungsanleitung

Sanyo

Sanyo VCC-6580P Bedienungsanleitung

Sanyo

Sanyo VDC-HD3500P Bedienungsanleitung

Sanyo

Sanyo VCC-ZM500P Bedienungsanleitung

Sanyo

Sanyo VCC-WB4000 Bedienungsanleitung

Sanyo

Sanyo DSR-HB8000 Bedienungsanleitung

Sanyo

Sanyo VCC-ZM600P Bedienungsanleitung

Sanyo

Sanyo VDC-C1572FP Bedienungsanleitung

Sanyo

Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCB-3512T Bedienungsanleitung

Sanyo

Sanyo VCC-XZN600P Bedienungsanleitung

Sanyo

Sanyo VCC-3944 - 1/4" Color CCD DSP Camera Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung