Sartorius PB-11 Bedienungsanleitung

98648-012-08

Operation Manual

Sartorius Basic Meter PB-11

Contents

4General View

6Warning and Safety Information

7Installing and Maintaining lectrodes

9Standardizing for pH Measurement

13 Using Setup

15 Standardizing for Millivolt Measurement

18 Understanding pH Theory

19 Temperature Compensation

20 Measuring pH

21 Troubleshooting

23 Meter Specifications

24 Accessories

25 CDeclaration of Conformity

General View

1Setup button:

Press to clear buffers,

revie electrode

calibration or select ne

autorecognized buffers

2Mode button:

Press to toggle bet een

pH and mV mode

3Standardize button:

Press to enter each buffer

4Enter button:

Press to select menu

item options

5Measuring icon

6Temperature

7Mode

8Result

9Prompts

10 Buffer icons

11 Icon: standardization

(calibration of the meter)

in process

12 Stability icon

13 Standardizing icon

14 Standardization result

Front Vie

Display

1.68 4.01 6.86 9.18 12.46 S1 S2 S3

1%/¡C

Auto

Man

Set

Clear

Error

1234567810101213

Sal

TDS

%DO

mg/L

S/cm cm ion rel mV pH

µK

°C

1Po er cable connector

2Reference electrode

connector (used ith

separate reference

electrodes)

3BNC electrode connector

4Temperature compensation

probe connector

5AC adapter

Rear Vie

Connecting to a Po er Source

Warning and

Safety Information

For safety and operating reasons, only authorized

service technicians may open the Basic Meter PB-11

housing. Therefore, only authorized technicians may

repair or perform maintenance on this pH meter.

Any tampering ith the pH meter or negligent or

intentional damage to this equipment ill void any

arranty claims against the manufacturer.

If liquid gets into the pH meter, unplug it from AC

po er (mains supply) and have an authorized service

technician check the pH meter.

If you do not plan to use this pH meter for a relatively

long period, please disconnect it from AC po er.

For safety reasons, use this equipment only for the

application described in this operation manual.

Make sure that the buffers used for standardizing

have exactly the same values that are stored.

Installing and

Maintaining lectrodes

1. Remove the protective end cover from the electrode.

2. Before first use of your electrode, or henever

the electrode is dry, soak overnight in a standard

solution or KCI solution.

3. Remove the shorting cap on the pH meter connector.

Install the electrode by plugging the BNC and ATC

connectors into the jacks on the rear panel.

4. Option: Install an ion selective electrode by removing

the BNC shorting cap and plugging the BNC connector

(t ist-lock) into the BNC jack. If a combination

electrode is not available, plug the separate reference

electrode into the ref pin.

5. Clean the electrode bet een each measurement ith

distilled ater or deionized ater, or part of the next

solution to be measured.

6. Store glass pH electrodes in KCI solution or electrode

filling solution. Make sure the liquid level of the

internal filling solution is al ays a fe centimeters

higher than that of the measurement solution.

Reference

Electrode

ISE

Standardizing for

pH Measurement

Because electrodes vary in their response, you

must standardize (calibrate) your pH meter and

electrode to compensate for electrode variation.

The more frequently you standardize, the more

accurate your measurements. Standardize daily,

or more often, for accurate results.

This pH meter allo s automatic standardization

using up to three buffers. Press the Standardize

button again to delete all the standardization data

stored up to that point. The pH meter performs

automatic temperature compensation.

1. Immerse electrode in a buffer solution. Stir gently.

Allo the electrode to reach a stable value.

2. Press the Mode button until your digital display

indicates pH mode. This button toggles bet een

pH and mV modes.

3. Clear existing buffers hen doing a ne 2- or

3-point standardization. Use the Setup button.

Also use the Setup button to select the individual

sets of buffers. (See page 13.)

4. Press Standardize. The meter recognizes the buffer

and flashes a buffer icon. When the signal is stable,

the buffer is entered. By pressing NT R you can

also enter the current buffer directly.

5. The meter displays the slope of the electrode as

100.0%. On entering a second or third buffer,

the meter performs a diagnostic check on the

electrode and displays the slope. (See step 7 ff.)

[Standardize]

Inhaltsverzeichnis

Andere Sartorius Messgerät Handbücher

Sartorius

Sartorius LMA110S Bedienungsanleitung

Sartorius

Sartorius PT-10 Bedienungsanleitung

Sartorius

Sartorius Sartobind IEX MA 100 Bedienungsanleitung

Sartorius

Sartorius MA45 Bedienungsanleitung

Sartorius

Sartorius BioPAT Xgas Vis Bedienungsanleitung

Sartorius

Sartorius MA50 Bedienungsanleitung

Sartorius

Sartorius LMA200PM Bedienungsanleitung

Sartorius

Sartorius PR 6130/04 N Bedienungsanleitung

Sartorius

Sartorius Combics Series Bedienungsanleitung

Sartorius

Sartorius MA160 Bedienungsanleitung

Sartorius

Sartorius MA160 Bedienungsanleitung

Sartorius

Sartorius WZA N Series Bedienungsanleitung

Sartorius

Sartorius MA150 Bedienungsanleitung

Sartorius

Sartorius Combics Series Bedienungsanleitung

Sartorius

Sartorius MA150C-000115V1 Bedienungsanleitung

Sartorius

Sartorius Docu-pH Bedienungsanleitung

Sartorius

Sartorius MA50-H Bedienungsanleitung

Sartorius

Sartorius LMA100P Bedienungsanleitung

Sartorius

Sartorius MA37 Bedienungsanleitung

Sartorius

Sartorius MA35M-115N Bedienungsanleitung

Sartorius

Sartorius PT-10 Bedienungsanleitung

Sartorius

Sartorius MA37 Bedienungsanleitung

Sartorius

Sartorius MA35 Bedienungsanleitung

Sartorius

Sartorius BioPAT Xgas Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung