Satel INT-SCR Bedienungsanleitung

INT-SCR

MULTIFUNCTIONAL KEYPAD

WITH PROXIMITY CARD READER

int-scr_sii_en 11/19

Quick installation guide

Full manual is available on www.satel.eu

The INT-SCR multifunctional keypad with proximity card reader is compatible with the

INTEGRA and INTEGRA Plus alarm control panels. It can work as:

partition keypad with proximity card reader – identified in the alarm system as

INT-SCR. It allows the user to control one partition of the alarm system. The device

makes it possible to manage access to a single door. The user can use the access code

or the proximity card (i.e. a 125 kHz passive transponder in the form of a card, tag, etc.).

entry keypad – identified in the alarm system as INT-ENT. It allows the user to activate

delay for the “3. Interior delayed” type zones in the partition controlled with the keypad.

The user can use the access code or the proximity card (i.e. a 125 kHz passive

transponder in the form of a card, tag, etc.).

partition keypad – identified in the alarm system as INT-S/SK. It provides the same

features as the partition keypad with proximity card reader, but the user can only use the

access code.

The keypad is designed for both indoor and outdoor installation.

red +12V

blue COM

green DTA

black CLK

yellow NO

pink NC

grey C

brown IN

purple BELL

Fig. 1. Keypad wires.

2 INT-SCR SATEL

1. Installation

The device should be installed by qualified personnel.

Disconnect power before making any electrical connections.

If an additional cable must be used to make connections, use the unshielded non-twisted

cable. If you use the twisted-pair type of cable, remember that CLK (clock) and DTA (data)

signals must not be sent through one twisted pair. The wires must be run in one cable.

1. Open the keypad enclosure.

2. Place the enclosure base on the wall and mark the location of mounting holes.

3. Drill the holes for wall plugs (anchors).

4. Using wall plugs (anchors) and screws, secure the enclosure base to the wall. Select wall

plugs specifically intended for the mounting surface (different for concrete or brick wall,

different for plaster wall, etc.).

5. Close the enclosure and secure it with the screw.

6. Connect the blue (COM), green (DTA) and black (CLK) wires to the appropriate terminals

of the control panel expander bus (see the control panel installer manual).

Fig. 2. Connecting the keypad to the control panel.

7. If the keypad is to control an electric strike, electromagnetic lock or another door actuator,

connect this device to the relay output as shown in Fig. 3. Depending on the device type,

use the following wires:

NC – pink (NC contact of the relay) and gray (C contact of the relay),

NO – yellow (NO contact of the relay) and gray (C contact of the relay).

It is not recommended that the door actuator be powered from the same source as the

keypad.

In the entry keypad mode, the relay output is disabled (you cannot control the

actuator).

SATEL INT-SCR 3

Fig. 3. Connecting the actuator to the keypad.

8. If the keypad is to supervise the door status, connect the detector supervising the door

status to the brown wire (door status input) and the blue wire (COM). If the keypad is not

to supervise the door status, connect the brown and blue wires together or, when

configuring the keypad, set value 0 for the “Max. door open time” parameter.

The door status input is not supported in the entry keypad mode.

9. Connect the power to the red (+12V) and blue (COM) wires. The keypad may be powered

directly from the control panel, from an expander with power supply or from a power

supply unit.

10.The purple wire (BELL output) you can connect e.g. to the one of the control panel zones.

11.Set the address and select the operating mode for the keypad (see “Address setting and

operating mode selection”).

12.

Power on the keypad.

13.Start the identification function in the control panel (see the control panel installer

manual). How the keypad will be identified depends on selected operating mode.

1.1 Address setting and operating mode selection

The keypad with factory default settings has address 0 and its operating mode is “partition

keypad with proximity card reader”. If you wish to change its address or select another

operating mode, follow the procedure below.

1. Power off the keypad (if it is powered on).

2. Disconnect the green (DTA) and black (CLK) wires from the terminals of the control panel

expander bus.

3. Short the green and black wires.

4. Power on the keypad.

5. The and LEDs will start flashing alternately (then, you can disconnect the green

and black wires).

6. Set the address or select the operating mode.

4 INT-SCR SATEL

Address setting

1. Press in turn and .

2. The LED will start flashing.

3. Use the numeric keys to enter a new address from the range of 0 to 31.

4. Press .

5. The and LEDs will start flashing alternately. You can proceed to select the

operating mode (press and in turn) or end the procedure (turn power off and

connect the green (DTA) and black (CLK) wires to the corresponding terminals of the

control panel expander bus).

Operating mode selection

1. Press in turn and .

2. The LED will start flashing.

3. Select the operating mode by pressing one of the keys:

- partition keypad with proximity card reader (INT-SCR),

- entry keypad (INT-ENT),

- partition keypad (INT-S/SK).

4. Press .

5. The and LEDs will start flashing alternately. You can go on to set the address

(press and in turn) or end the procedure (turn power off and connect the green

(DTA) and black (CLK) wires to the corresponding terminals of the control panel expander

bus).

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu

Andere Handbücher für INT-SCR

Inhaltsverzeichnis

Andere Satel Tastenfeld Handbücher

Satel

Satel INT-SCR Bedienungsanleitung

Satel

Satel VERSA INT-TSH2 Benutzerhandbuch

Satel

Satel VERSA-LCDM-WRL Bedienungsanleitung

Satel

Satel INT-TSG2 Bedienungsanleitung

Satel

Satel INT-TSG2 Benutzerhandbuch

Satel

Satel INT-SK Bedienungsanleitung

Satel

Satel INT-TSG Bedienungsanleitung

Satel

Satel CR-MF5 Bedienungsanleitung

Satel

Satel INT-TSI Benutzerhandbuch

Satel

Satel CA-64 S Bedienungsanleitung

Satel

Satel VERSA-LCDM-WRL Bedienungsanleitung

Satel

Satel Integra INT-KSG2R Bedienungsanleitung

Satel

Satel INT-TSG Bedienungsanleitung

Satel

Satel PRF-LCD-WRL Bedienungsanleitung

Satel

Satel INT-SK Bedienungsanleitung

Satel

Satel CA-6 KLED Bedienungsanleitung

Satel

Satel INT-TSG Benutzerhandbuch

Satel

Satel VERSA INT-TSH2 Betriebsanleitung

Satel

Satel INT-SCR-BL Bedienungsanleitung

Satel

Satel CR-MF5 Bedienungsanleitung

Satel

Satel INT-TSG Benutzerhandbuch

Satel

Satel INT-S-GR Bedienungsanleitung

Satel

Satel abax2 Bedienungsanleitung

Satel

Satel INT-KSG Gebrauchsanweisung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung